Having problems with your Dishwashers ?

Hotpoint Dishwasher Bought it new 2 weeks ago. Seemed to be working ok. Last night it started leaking out the front door (suds). I disconnected the drain line (tried to blow through line to tub, NO GO) so I started it and ran it into the sink. It seemed to be flowing OK, but there is still about 1/2 inch of water inside washer. Is this OK? Model # HDA3400G02BB


Answers :

Water will not come on. started 3 months ago being erratic, some time it would work, some time it would not. Now it has gotten solid.
Everything runs except water, therefore no wash.
Have you tried adjusting the feet on the front of the washer so it is tilted back slightly .This will stop the water from coming over the little lip on the front of the machine. Some dishwashers also use a little amount of water in the bottom when drying asthis helps to curculate the heat ; leave the washer to complete it's cycle and it should beep to let you know when it is finished
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hotpoint Dishwasher Bought it new 2 weeks ago. Seemed to be working ok. Last night it started leaking out the front door (suds). I disconnected the drain line (tried to blow through line to tub, NO GO) so I started it and ran it into the sink. It seemed to be flowing OK, but there is still about 1/2 inch of water inside washer. Is this OK? Model # HDA3400G02BB


Water will not come on. started 3 months ago being erratic, some time it would work, some time it would not. Now it has gotten solid. Everything runs except water, therefore no wash. ... Dishwashers

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

Hi My dishwasher stopped mid rinse cycle, with a little water still in it. Lots of beeping later i managed to set it back to start but it wont go, just beeps. The line to sink seems to be clear. There is no gurgle sound when i try to start it. model number SB907WJ*00


Hi,Is there my error code there?If you set the appliance to drain do you hear the pump running?Bail the water out manually and then take the filters out.Bail out the water below the filters.Take off the ... Dishwashers

I have a new Hotpoint Dishwasher HDA2000T00WW. Ran it once. Now it seems to have no power. Nothing starts. Disconnect switch is on and line voltage observed at connections to dishwasher. Does this have a reset button on motor which may have been tripped? Any other possible things I could check?


... Dishwashers

I have a Kenmore dishwasher (363.16222100) that isn't getting water into the unit/tube. All the other cycles seem to be working fine. I've replaced to water inlet valve and it's still not getting water into the tub to start the wash. Checked the water line and it's fine. Any ideas?


The only thing left is to replace the main control board ... Dishwashers

Hello, I have a couple year old brigs and strattion upright pressure washer. It has always ran great untill recently. It will run for a acouple minutes before dying, like it is starving for fuel. i give it a couple of minutes, it starts right back up and again dies after a couple minutes of use... I have takin the float bowl and float off and cleand the gas tank and fuel line. everything seems to be in order. Do you have any ideas what it could be? I have not tuched the top side of the carb sinc


Check the oil level in the engine itself. Verify that your oil reservoir is full, then try again.You may also want to refer to the owners manual for other trouble shooting tips. Click this link to go to your manual.http://www. ... Briggs & Stratton Gas Pressure Washer 20244

Water problem Hi, I have a Jenn air DW 711 that does not get water. I checked the following: Water line: I unhooked the water line and it is clear & free flowing. Float: The float moves up and down as it should. Filter: The filter inside the tub is clean. The motor runs and will drain any water in the tub I put a bucket of water in the tub and the dishwasher immediately drains no matter which setting I choose. Any ideas? Thanks, Steve


Many dishwashers will drain at the beginning of any cycle. \015\012If the water does not fill after the pump-out cycle, then the problem is either the fill valve or the float switch. You should be able to hear the float switch click as you rais ... Dishwashers

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

Bosch Integra SHU 9955US/12 - when we start wash cycle, the detergent dispenses and the tub fills with water, but the wash cycle never starts (never spins spray bars). Seems like timer is counting down, though, but doesn't start "washing". After waiting awhile, we are able to use the "Cancel/Drain" mode to drain the water. The drain filter in the bottom of the tub is clean.


Sounds like your motor is burned out. The drain motor and wash motor are seperate on your machine. You can check for power going to the motor, but to do this you might have to pull the dishwasher out. While the cycle is running check for 120 VAC g ... Bosch SHU9955UC Built-in Dishwasher

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi. I have a 3 year old LG dishwasher. It will not drain. Display shows OE. I completely cleaned the drain assembly inside the DW. I checked the discharge line, it is completely clean. I disconnected the drain line from the air vent assembly at the sink and ran the DW, still will not drain. I disconnected the discharge pump wires and ran current directly, the pump works. I replaced the main control PCB, still will not drain. Please advise. Thanks


Measure the electric resistance of the Drain Motor. (Value should be 20-40 Ohms) If it is out of spec, replace it.\015\012\015\012Please reply with what worked best. Thanks! ... LG 24 in. LDF 7811 Built-in Dishwasher

After putting too much down the garbage disposal, the sink will not drain and the dish washer (Whirlpool Quiet Wash) will not drain. I have disconnected all sink drain pipes and snaked the main line to be sure lines are clean. The drain hose from the disposal to the washer seems clear. What should I try next?


You need a longer snake had one on friday that wa about 40 feet out it took two trys to get it good luck ... Dishwashers

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

My dishwasher often finishes its cycle and there is still water in the bottom of the tub. it seems like some timer/cycle is out of sync. because if i start a new cycle it seems to finish draining first before starting to wash again. is there an easy way to reset this?


Sorry to read about your problem, I hope this helps you out.you have a clogged pump,hose or sump areaI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

2 brand new Kenmore elite dishwashers - All hookups checked and correct. Start buttons blink - cycles will not start. 1 washer ran for about 10 seconds - then the light started blinking. Troubleshooting in manual says light will blink if the door is not closed. They seem pretty closed. Dishwashers leveled and plumb. Tried it mounted, and unmounted. No Luck. Thanks


These dishwashers have a safety feature. The door has to be closed within 3 seconds of pushing the start button. If the cycle is interrupted at all by opening the door or pushing something while started you will have to push the start button to resum ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My GSD900G-01 dishwasher leaks where the hot water is supposed to go into the tub. There's a plastic fitting that seems to be glued to the side of the tub and the hose from the inlet valve goes to the top of this fitting. There are no visible cracks or other damage but there is some rust inside the tub at the fitting. The fitting has two open gaps on it's side which is where the water is leaking out. It looks like the water is supposed to flow past these gaps (which I'm guessing are there to


Hi, I seen where this posted on premium. If you still need assistance, please let me know. I can help you through this.\015\012\015\012Vic ... Dishwashers

Whirlpool Dishwasher ADG 450. Start as normal and it keeps intermittentlly stopping and starting. Washs / drains fine, but sometimes cycle seams to last for a couple of hours. I think it is four beeps when it is stopping and then immediately starts again. We had a problem months ago where as the sink was draining into the dishwasher out pipe, so dishwasher wasn't draining / filling up. Fixed the problem by turning the pipe the other way so water couldn't flow that way - but I don't know if that


... Dishwashers

Dishwasher i need help either installing for troubleshooting my 18' portable frigidare dishwasher. when the dishwasher is turned opn and it starts to fill the water flows out of the bottom of the machine what is the problem and how dod i fix it is it the hoses ? it also hooks up to the sink it isnot a built in dishwasher so is the hose for the draining need to go in the sink or does it hook up somewhere under the sink?


I would put the dishwasher on its back so you can see underneath to check the fill and drain hose to make sure there not damaged in any way to cause it to leak. if it all looks good under there return it upright and remove the front lower kick panel ... Frigidaire 18 in. FDR252RB Built-in Dishwasher

I purchased my KARCHER G2500VH last summer. I used it one time for about an hour. I tried to start it today, seems like its not getting gas. I checked the gasline to make sure gas was flowing. I removed the sparkplug, poured a little gas into the engine through the plug hole. Replaced the plug, pulled the rope and it started for about two seconds. I also poured fresh gas in tank. Cannot get to start.


Have tried to start our BlackMax 2700psi pressure washer, it is not getting gas to the carburetor, what to do? ... Pressure Washers

GE Dishwasher, model: GHDA470MBB When you turn it on, the motor seems to run for a minute or two and then just stop. It started not cleaning the top rack, I ran JetDry hardwater cleaner in it. Then the bottom rack didn't seem to be getting clean either. Next, it just doesn't seem to work at all as described above. It is fairly new, bought July 2006 (but wasn't used from March 08 to August 08). Thank you for your advice.


... GE GHDA470MWW / GHDA470MBB Built-in Dishwasher

Dishwasher leaks When we start the dishwasher we hear it try to start but no water enter the inside tub. If we hit the cancel button it shuts down and water starts spraying from underneath in the area where the main wate line hooks up.


Sound like the fill valve is not working. I woudl check the hoze for a clogged screen ,then replace the fill valve if no clogs found.  ... Kenmore Dishwashers

Hello i have a Baumatic slim line intergrated diswasher . it has 18 lit up on screen but it will not let me set any programme when i press p. It is not starting a wash at all any ideas it did trip once last year and the help line gave me a code to put in after i had unplugged it for 24hrs this seemed to work but i can't remember code any advice appreciated thanks


... Baumatic 18 in. BHD45 Slim-Line Built-in Dishwasher

Engine satlling Does anyone know why my pressure washer keeps doing this, it dosnt matter weather the hoses are attached, with water flowing, it just seems to run fine for 2min then start pulsing and the completely stall?it started happening after i filled it up with petrol


If it acts like this with the hoses disconnected, I would guess that either you got bad gas, or if it was sitting for a while before this, that there is varnish in the carburetor and when the choke goes off it starves for fuel. I would try Seafoam o ... Honda Black Max 2600 PSI Pressure Washer

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1408 seconds