Having problems with your Dishwashers ?

No power to Selections, Water Did Not Drain

\015 Our Whirlpool Quiet Partner II washed our load of dishes, but didn't drain out the water. When we noticed that the water didn't drain we closed the door and pressed the Drain Button. Nothing happened. Next, we tried to select other buttons but noting was functional. The door is latching properly, I checked the main breaker for the disherwasher and it did not trip. I removed the bottom panel cover of the dishwasher to manually drain.So now we now have a drained dishwasher with no power to it for any selection. I also turned off and then turned off the main breaker in an attempt to reset it. Did not work.Need help.Thanks.\015

Answers :

When you remove the bottom panel cover, check the wiring connection inside the junction box on the right for a loose or shorted wire.
If that's ok, open up the console and check the continuity of the thermal fuse that's clipped to the control board. Chances are it needs to be replaced.
Good luck!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No power to Selections, Water Did Not Drain


When you remove the bottom panel cover, check the wiring connection inside the junction box on the right for a loose or shorted wire. If that's ok, open up the console and check the continuity of the thermal fuse that's clipped to the control b ... Dishwashers

Belling Dishwasher IDW450. When turn on power button it starts bleeping. About 25 times. The you can select your program, it sounds like it is draining but then doesnt do anything else. Cant hear any water running in. I have turned the power off and back on. Water is connected


When you say you have turned the power off and back on. do you mean the switch on the appliance. if so turn off the power by removing the fuse from the fuse panel for the dishwasher. wait about ten minutes, put the fuse back in and see if that res ... Belling 24 in. IDW603 Built-in Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

My dishwasher (kleenmaid brandt super silent DW121TB) appears stuck in a wash cycle; how do I reset the program? I have read the instruction book to no available, tried unplugging power overnight, tried a combination of simultaneously holding buttons in and switching on, letting the machine run all night, drained the water and added clean unsudded water, and none have corrected the situation. There is also a selection lever inside the machine that is not identified in the instructions, it appea


When you say it is stuck in a wash cycle, do you mean the wash arms are continuously running?\015\012Is there water in the base when you open the door?\015\012\015\012Can you try to run the dishwasher in any other program like rinse ... Dishwashers

Fisher & Paykel DW60. Fault: Will not start regardless of program selected. E.g. if "heavy duty" pressed, only light will flash, if "normal" is pressed, only this light will flash etc. All hoses (water and drain) have been checked and no crimps or blockages found at either end. All usual methods tried (e.g. cleaning strainers and filters, turning power off for a while etc). Finally, while lights are working, the machine makes no noise at all when a pogram is selected.


... Dishwashers

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

I have a Bosch Diswasher that is not draining. I have disconnected power for 35 minustes and used shop vac to excess water out of drain line. i also pulled all water thru the drain line from the tub itself. i assume that because i could pull the water, all baffles and lines are clear as i emptied the tub from drain line. you can hear the pump come on to drain water but no water is moving. What would be my next step. If it is to replace the pump, how do i easiest access the pump to remove and rep


Either the selector switch or pump is faulty. If there is not any clogs anyways. The system may need to be reset. Most resets are done by entering a series of numbers on the touch pad to enter diagnostic/test mode where the machine can be reset. This ... Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

No power, water did not drain


Float valve is jammed.Look inside the machine on the floor will\015\012be a small float valve. Looks like a small upside down cup. Lift it and\015\012clear anything from underneath. The valve is a safety feature\015\012to stop ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Our Dishwasher is not draining. We tried to run a test cycle and noticed there is no power. We checked the Electrical Panel and noticed that an unmarked breaker was tripped. We turned it on but still have no power. All other electrical items are working in the house. Is the power being cut off as a fail-safe function due to the water not draining? How do I fix the drain/pump? Please Help!


Hi,No, the water is a result of the dishwasher going off mid-cycle...Take the front kickplate off and see if you have power at the makeup box...you will need an electrical meter to check that...if there is power there then you have ... Dishwashers

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

Dishwasher will not drain. power is ok drain hose is not plugged disconnected hose from drain plug was able to siphon smome water through Start washer, then press cancel, get a noise, probablely motor, but no water. Model MDB7600AWS serial 15416386ce


Hello. There are several possible causes for your problem. Let me briefly go through each one and then you may be able to zero in on your specific issue. I will try to include the fix for each. \015\012\015\012Drain line/air gap\015\012\015\0 ... Maytag Dishwashers

Bosch SHX46A02UC-21 Won't Fill and Drain Runs Continually. Original presentation of problem was that it wouldn't drain. Discovered that Garbage Disposal had plugged drain line. After clearing Drain Line, now drains fine but the drain pump runs continuously and it never fills with water. Have done the Cancel, Power Off routine however, even after that, drain pump runs continually.


Float switch is in the flood position and the drain pump is running..\015\012there is water under the dishwasher or that switch is stuck up.. ... Bosch 24 in. SHU43 Built-in Dishwasher

Not draining we have a ge quiet power dishwasher it started not draining fully, I took the hose off under the sink and seemed to be lots of water running when i put it on rinse cycle but when I opened it up still water in bottom just wondering what it could be?


Are you sure your drain system is not clogged or restricting water flow ? When you say youtook off the hose off under the sink and it seemed to be lots of water running on the rise cycle .. that suggests that you may have a restriction af ... Dishwashers

Model 818s stops mid cycle and beeps continuously. water not drained out. water on floor. no lights on. shut power off and leave 1 hr. turn power back on and still beeping


... Fisher and Paykel Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Frigidaire Dishwasher model # FDB520RHB2 Stopped prematurely last night while on light cycle, now will not respond at all. Noticed water at bottom of tub; tried draining manually through drain tube, removed lower arm, glass trap, and filter, and water remains; tried electronic reset by switching off breaker for several minutes; all to no avail. Electronic controls (cycle/option select) will not respond at all.


This is not a uncommon problem and it sometime's is the pc control panel but i find that it is more often the interlock ( latch assembly .) i would change // there has been a improvment and i belive this will solv ... Dishwashers

Our Bosch dishwasher #SHU9922UC (FD8007) will not turn on properly. Only its drain pump starts -- and keeps running -- when it's powered on and the door's closed. Pressing the two "drain cancel" buttons for more than 3 seconds doesn't help. Neither does cutting off power, then turning it back on in the hopes of resetting the machine's 'computer'. No water inflow occurs. Help?


I had a similar issue after I replaced a bad drain pump, seems the logic got hung up.. I poured in a pitcher of water, closed the door, it drained and was then ok - worth a try. If not, you may have a bad water level switch. ... Dishwashers

LG dishwasher quit mid cycle. no power to the front panel. I drained the water and found a two pronged wire by the drain hose disconnected. reconnected it and I still get no power on the control panel


Here is the video for you its intresting to get it repaired V ... LG Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1434 seconds