Having problems with your Dishwashers ?

I have a Kenmore Ultra Wash Dishwasher and the 3rd level spinner broke off. I have a new one and now need to know how to replace it.


Answers :

You don't have to remove the top dish rack, but it might be easier unless you're flexible. To remove the dish rack, remove the "stop" clips from the front end of the tracks and pull the dish rack out.
Remove the screw holding the water supply feed tube to the inside top of the cabinet. Slightly pull down the feed tube and remove the old plastic pushpin retainer from the hole. Install the new pushpin retainer.
Holding the pushpin retainer from the top with your finger, install the 3rd level spinner and clip the new pushpin in place. Gently pull down on the spinner and give it a spin to make sure it's properly installed. Carefully reinstall the feed tube screw (in case it falls into the motor). Reinstall the top dish rack and you're ready for action.
Good luck!
The manifold in the back of the dishwasher needs to come out. you can either pop it all the way out it only undo it halfway if your arm is small enough.. there are either 2 tension clips or 2 screws holding it to the top and back. if you undo the top of the manifold and pull it down you should be able to slide the new part in place. the plastic push pin goes on top of the manifold and the spinner goes on the other side. it may be a little difficlt to push the 2 together..
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Ultra Wash Dishwasher and the 3rd level spinner broke off. I have a new one and now need to know how to replace it.


You don't have to remove the top dish rack, but it might be easier unless you're flexible. To remove the dish rack, remove the "stop" clips from the front end of the tracks and pull the dish rack out.Remove the screw holding the water supply fe ... Dishwashers

I have a Kenmore Ultra Wash Dishwasher model 665.16379301. The spinner from the top of the dishwasher has come off. I have a replacement part but need to know what is required to replace it. Do I need to remove the feed tube assembly in order to replace it?


... Kenmore Dishwashers

I need to replace the springs for the door of my Asea Skandia Cylinda 1200 dishwasher. Can anyone please tell me the specifications for the springs so I know what to ask for when purchasing new ones?


Hi, welcome to FixYa.\015\012\015\012I have complete specs. and part numbers on my home PC but I am away for a few more hours. \015\012\015\012If you wouldn`t mind waiting a while ( 3-4 hrs. ) I can certainly help you.\0 ... Dishwashers

My Viking dishwasher top rack needs to be replaced. Do you know where I can purchase a used one? The new top racks are $350 or more. My model number is VUD141


... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Indesit di260 hi door catch has broken got new one need to know where the screws are hidden to undo this to replace it thanks


Indeset DI620 appears not to be pumping water in, light 1 flashes as error code is it the motor? ... Indesit 23 in. DV62 IX Built-in Dishwasher

We need to replace the locking ring in the bottom of our Asko 1716 dishwasher.(It's cracked) I can only find one kind of replacement ring for that,but it looks like the right size. I need to know if Asko uses one ring for more than one model of dishwasher?It's a 5" locking ring for the bottom well of the tub. Thanks for your help!


Only 1 size ... Asko D1716 Built-in Dishwasher

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

I have purchased a repalcement detergent dispenser-assembly and do not know how to take old one out and relpace with new part. The new part has a face plate that snaps on to the screw mounted base plate assembly which attaches to the door. I need to know how to remove the old dispenser and install the new dispenser without breaking parts and scratching the door. Is there a schematic or exploded repair view I can check out or even written directions?


Hello\015\012& Welcome to FixYa\015\012\015\012To replace the detergent\015\012dispenser you can check this video. The video gives you step by step\015\012instructions:\015\012\015 ... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher

I have a go kart with a honda power washer motor that I just purchased.It lacks power at start and stalls alot.Put new pull in,sprayed carb cleaner,adjusted carb,new air filter,need to know if it need a fuel pump and were to get one


Hondas are gravity feed no pump needed .You might need to clean the card though. ... Karcher 2500 PSI Pressure Washer

10 year old Kenmore Ultra is leaking early in the washing cycle. Wondering if this is worth fixing or need to bite the wallet and buying a new one. I am worried about affecting the new cabinets even though the dishes seemed to be clean on the two occasions that the dishwasher has leaked. Only need a somewhat simple machine- I'd appreciate any suggestions as to what brands I should research if buy is the conclusion. Thanks.


At 10 years old I wouldn't put much if any money into it. Do check the water connections as it may be something simple that just needs to be tightened or a washer replacement. Replacing the valve is a simple and inexpensive fix but don't bother going ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

KitchenAid Dishwasher KUDP01FL: Called repairman to replace balance link kit. Then door extremely stiff to open & heard loud pop when one of the ropes came off the roller. Repairman came back & put rope back on & replaced door seal, then the door won't close & he claims need a new door latch. When he left, door again extremely stiff to open & heard same loud pop when one of the ropes came off the roller. Now he says he can't fix it and to call someone else. I now have three problems: (1) The doo


May have bent door hinges,, need to check all alignment of door, hinges and latches... ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Im replacing a frigidaire with a whirlpool and the problem I'm having is the electrical connections. My old Dw had two elec cords running to it. One small one that runs in the same direction as the drain and water hose runs the other is a slightly bigger elec cord that runs straight out the back of the cabinet unit and I cant tell where it goes. But it has on it anaconda w dutrax type nm 12/2 with grounding 600 volts.Do I need both elec cords for the new whirlpool or just one? All the online vid


Hello. Older houses offer all kinds of challenges. In the long run though, that is part of the joy of life. \015\012\015\012You need three things to hook up a typical dishwasher:\015\0121. The hot water source which goes to fee ... Dishwashers

I need a new dishwasher What do you recommend between Kenmore Elite. Quietguard Ultra. Model no. 665.77962K703 versus LG model LDF7920 I get conflicting information- a repairman we know says LG is the better make, needing far fewer repairs than Kenmore in general ( this washer I am thinking of buying was made by whirpool, I was told at the Sears store) But online reports claim LGs need the most repairs. HELP OR... do you have something else to recommend?


... LG Dishwashers

I have model number KUD 101TJBL0. I have spent about 300.00 on repairs. It keeps blowing the thermal fuse. I have had it replaced sev. times. My repair man has given up on solving the problem. I did read on another website that you need to replace the wiring kit that comes with the fuse. Me service man never did that and when I asked him about it he said that is not the problem and would not replace it. So, before I just scrap my diswasher and but a new one I thought i would order another fuse k


Hi,This applies mainly to Kenmore Dishwashers with the model number\015\012665.15835791 but also to any Whirlpool or Kenmore dishwasher with an\015\012electronic display. There are several possible trouble makers on this\015\012dishwasher ... Dishwashers

I need to replace my dishwasher. I need to know size specs to order one that will fit. My measurements are a little dif. Then what is offered. Can anyone help??? Ge model no. Gsd4030y70ww


... GE Dishwashers

Replacing dishwasher and need the dimensions for the Whirlpool Gold GU980SCGB3 Built-in Dishwasher to make sure the new one fits where this one is currently. Can you help?


... Whirlpool 24 in. GU980SCG Built-in Dishwasher

The cable to the door of my GE Potscrubber 900 dish washer (model GSD900L-02) broke. I purchase the replacement cable and now need to know how to reinstall this new cable. The replacement parts include two cables and two springs. Can you provide a "visual" of how this cable connects to the lower left corner of the door???


Question, my cable just broke yesterday. Where did you buy the part? ... Maytag Dishwasher

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

Need wiring diagram for a hotpoint df22 dishwasher on/off switch, the switch in it has been replaced with the wrong one so i have no reference to connect up the new one. thanks


You're in luck - I've just had one apart to repair the wiring loom.\015\012The door switch is a simple two-pole latching switch with the wiring as follows.\015\012\015\012This is the order of connections from the front.\015\01 ... Dishwashers

I have a tecnik tkd 795/2 i need to know the size of this dishwasher, need to get a new one


Tecnik tkd 795/2 Is 60cm in with ... Dishwashers

My PDW9280LOSS GE Profile diswasher runs and cleans fine. However, the high heat(sanitize cycle as well) does not finish ther job. A while back I changed the element due to hard water damage. I beleive I need a control module and I need to know if there is any sequence to reconnect for reprogramming (the new one)it? Or anyother ideas? Thanks


Hi,Before replacing that module I would check for power at the element first to confirm that there is no power....coming from the module...As far as the change out goes... just make sure the power is off when changing... then ... GE 24 in. PDW9280LSS Built-in Dishwasher

I have a ge nautilus built in dishwasher and do not know the model number it is 7 years old and came with house. need to replace and am unsure of dimensions for correct sizing on new purchase


You can find them on a label on the tub wall just inside the door. However 99% of all DW are a standard size and the difference is made up by adjustments of the threaded leveling /adjustment legs.Standard size is 24" x 32-36"...you can ta ... GE Nautilus 24" Built-in Dishwasher

My dishwasher did not come with power cord. what kind of cord do it need and how do i connect the cord? On the new cord how will i know which one to connect to the white and black wire? The dishwasher is Whirlpool model du930pwsb, Sku numbmer 451-5344.


120 Volt 16 gauge, 3 wire power cord.\015\012\015\012Brass Screw is Black, White Screw is is Common, Green is Ground....Try Home Deport for a cord. If no screws are on the dishwasher, use wire nuts and elec. tape ... Whirlpool 24 in. DU930PWP Built-in Dishwasher

Whirlpool LE9500XTW0 Dryer won't start, thin flat metal piece broke off inside front, top, right hand corner where the door closes up. Called a repairman who said I needed to purchase a part, but I don't know which one, nor how to replace it. Anyone...?


The part could be your door switch lever if the dryer is not starting. For clarification, go to pcappliancerepair.com and type in the model you provided. Look at item 9 under the Section 02 drawing and let me know if this is the part you are referr ... Dishwashers

3 PROBLEMS 1. SPRAYER ARM LIGHT ON BUT WHEN I OPEN THE DISHWASHER THERE IS NOTHING BLOCKING THE ARM FROM SPINNING. 2. SALT LIGHT IS ALWAYS ON. HOW DO I ADD SALT. 3. I NEED NEW TRIM FOR THE OUTSIDE OF THE WASHER. WHERE CAN I GET THAT. OH ONE MORE 4. IS THERE A WAY TO HAVE THE WASHER SERVICED SO I KNOW IT'S IN GOOD WORKING ORDER. LIKE A CAR TUNE UP? WHO DO I CALL? THANKS!


This is just to let you know that the internal water softener needs water-softener salt. If you do not use the softener (I do not at my house) then the light serves as a convenient on/off light.The other issues you have can ... Miele 24 in. Incognito G843SCVi Built-In Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1237 seconds