Having problems with your Dishwashers ?

Whirlpool GU2500XTP dishwasher went dead in mid-cycle.

\015 Replaced control panel without success. No lights on control panel and no response to controls.\015\012\015\012Wondering if this model has had reliability issues with the circuit card.\015\012\015

Answers :

"Wondering if this model has had reliability issues with the circuit card." ...If by circuit card you mean the electronic control board, that part number is used in many other models as well. In my experience with these control boards, I believe they have a low failure rate.

Make these checks if you haven't done so yet...
Check for 120V (breaker). Look for loose/shorted wiring connection at the\015\012dishwasher's junction box. Check all wiring connections to the control panel, electronic control and thermal fuse. Test the continuity of the thermal fuse (part # 8193762). If that's ok, you have already replaced the control panel so the problem is likely with the electronic control board (part # 8564546).
Good luck.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whirlpool GU2500XTP dishwasher went dead in mid-cycle.


"Wondering if this model has had reliability issues with the circuit card." ...If by circuit card you mean the electronic control board, that part number is used in many other models as well. In my experience with these control boards, I believe they ... Dishwashers

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

Does a Whirlpool ADG 6552 dishwasher have a thermal cut out or re-set button? If so, where is it located? The dishwasher is dead (no lights) it stopped mid cycle. There is power up to the board and the door latch is OK too. Thanks.


How do you know there's power to the board? If the board has power but no display you need a new control board. Here you go http://www.4whirlpool.co.uk/catalogue.pl?ss=1&path=600157&model_ref=272119&refine=board ... Dishwashers

My Bosch dishwasher Model SHE44C02UC just went completley dead while washing. My wife and I were in the living room and heard a ''pop'' and went to investigate. We discovered the dishwasher was completely dead with no lights on at all. The on/off switch does not work. I checked the breaker and it is okay. Also the disposal is also on this circuit and it still works so I know the circuit is okay. There is still water in the bottom of the dishwasher - no suds - so it may have been in a rinse cycle


Well done on confirming that the outlet is not the problem. This problem will not be able to fixed by the owner and a service call is the next step. (unless you want to dig into the problem, which could easily be a failed pump motor which took out t ... Bosch Dishwashers

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Whirlpool dishwasher gu3600xtvb2 stopped in mid cycle


... Whirlpool GU3600XTV Dishwasher

Danika dishwasher drain motor running continuously after power went off mid cycle and dishwasher was turned on again. Some leakage occurred. New cycle not starting. How do I reset it?


... Dishwashers

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers

Whirlpool Gold Quiet Partner IV Dishwasher, Model GU1500XTKT0, Serial number FL4104935, Type 575-0, during a Rinse Only cycle suddenly the cycle light began constantly blinking, which could not canceled or stopped nor placed into diagnostic cycle or other wash cycle. The repairman checked everything and decided problem was Electronic Control Module, which he replaced; blinking Rinse Only went off, but Normal Wash is now constantly blinking and repairman seemed confused and is wanting to repla


... Whirlpool Dishwashers

After final rinse on my Whirlpool dishwasher panel went dead


Check your main power input. Switch off and ON. If no displayInternal fuse / circuit would have tripped. Try replacing / Resetting. No improvement contact service center for assistance. ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My whirlpool adp 553 dishwasher stopped mid-cycle with water in bottom, no power light. Power light goes on if door is opened. Can you please help me?


... Whirlpool 24 in. DU948PWPQ Built-in Dishwasher

Whirlpool dishwasher du100xtpba, stopped mid cycle...


... Dishwashers

I have a Whirlpool quiet partner III dishwasher that began to make a loud scratchy noise when the cycle started. This went on for a few months but it was still cleaning the dishes. Last weekend we tried it and it just kind of stopped---there is a kind of buzzing at the point when the cycle should start and then it does nothing. It does still drain of the cancel cycle. What does this sound like


There could be some debris obstructing the spray arm assembly from turning freely, puting extra working load on the motor and it now started to cut off(thats why you get the buzzing noise) since the motor also activates the water pump(reversible) it ... Whirlpool Dishwashers

Whirlpool Dishwasher model DU930 stopped before cycle completed. There is still some water in the bottom. Dishwasher will not restart. Touch panel is dead, as if there is no electric. I checked the incoming wires and there is electric being supplied to the dishwasher. Any suggestions? Thanks.


... Dishwashers

Whirlpool Quiet Partner II dead mid-cycle; no lights; nothing


... Dishwashers

Whirlpool dishwasher won't drain and won't run cycles - it's dead


... Dishwashers

Whirlpool dishwasher stopped in mid cycle


Check your chopper inside ur unit. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Whirlpool Undercounter Dishwasher DU8900XY1, My dishwasher is dead. It stopped in the middle of the wash cycle and has not operated since. I checked the power at the junction box and power was confirmed. I could not see or smell any burnt wires. I don't know the next thing to trouble shoot to fix the problem. Please help


Take off the kick panel and open up the j-box at the dishwasher only. Just make sure there is no burned wire nut or loose one\012\012Thanks ... Whirlpool Dishwashers

I have a Whirlpool Dishwasher that won't rinse the glasses in the top rack. The chopped up food bits from the other dishes are left in the bottom of the glasses. I don't think it's a problem with the wash cycle as the glasses are cleaned of the material they went in with. I think the rinse cycle is depositing excess food onto the glasses.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heat ... Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

I have a GE Quiet Power 3 dishwasher that was working fine last week. Over the weekend I ran it and we could hear a banging noise, so my boyfriend opened it three or four times in a row (during the cycle) to figure out what it was. The fourth time, it went dead. I checked and it had tripped the breaker. I reset the breaker and the dishwasher seemed to be working again, however the lights on the front were flashing (they hadn't previously), and now it will run for about 10 minutes but no water ru


Were you able to figure this out? We have the same problem here! ... Maytag Dishwasher

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

The dishwasher trips the safety switch in the meterbox. whirlpool ADP 5000 made in germany (not on the drop down list) the 1st time was after a finished cycle and the power was off in the morning. the second time the power was on at the wall and when thw nob to select the cycle was turned, the power went off. any ideas would be really appreciated. julian


\015\012Please DO NOT touch this machine IF the power is ON. There is a possibility of shock. The reason, the ONLY reason, that the Breaker "Trips" is, if there is a, Phase fault to Earth/Neutral, in other words the CA ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a Whirlpool dishwasher, model DU943 that's under 7 years old. I went to use it last night and it won't power on. I tried selecting all of the cycles, but the dishwasher never came on. I looked through the troubleshooting tips in my manual (like checking the circuit breaker for a tripped fuse, which was fine) and I still have a problem. what else can I try? thanks.


Hello- This unit has a thermal fuse inside the door panel on the control. This part is replaceable. If it is bad, replace.- and would suggest not using heated dry as this is most common cause of fuse failure. Let me know if this info helps- have more ... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1652 seconds