Having problems with your Dishwashers ?

No water supply to dishwasher

\015 No water is getting into the dishwasher. Error 4E indicates a water supply problem. Have confirmed connected properly, valve is open and supply line is not pinched or clogged. Please help.\015

Answers :

Water solenoid!? also check.. on mine there is a breather tube on front bottom of washer(inside) round part about 2 1/2 inches..check and clean this...fixed mine! free fix
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No water will enter the dishwasher, There is no problem with the water supply or the supply line. The water flows from the supply line to the dishwasher connector but does not enter the dishwasher.


The water-inlet valve lets water enter the machine. Make sure it's not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if you get power to valve when unit is put into operation ... KitchenAid Dishwashers

I have Frigidaire FDB956RBC1 diswasher. I have to turn off the water to fix the faucet. When I turned the water back on, water did not go to the diswasher when I used it. The diswasher runs normal except with no water going into it. The water runs find at the facet. There is separate water supply underneath the sink for the faucet and the diswasher. I wonder if there is a mechanism with the dishwasher that stop the water from going into the dishwasher after the water supply been turn off. I did


FRIDG... EXPERT HERE \012\012\012Welcome to fixya\012\012Hello\012\012 \012\012 ... Frigidaire FDB956RB Built-in Dishwasher

No water is getting inside my Bosch dishwasher compartment. Water supply to dishwasher is ok. Checked hose at input of dish washer and water supply is ok. Could pump have packed in? Model 004 920 378. Dishwasher used daily since 1999.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch Dishwashers

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

Hi I went to put my Bosch dishwasher on this morning only to find that it would not come on . there was water in the bottom of the dishwasher so i cleaned all the water out and cleaned all the filters but my dishwasher would still not work it was only when i went t o disconnect the dishwasher from the water supply did it come on Can you please let me know what problem i have with my dishwasher and is it likely to happen again


Hello,\015\012\015\012This video will help you fix your ouch dishwasher.\015\012\015\012 ... Bosch Dishwashers

Re: Bosch Dishwasher Model SHX46B06UC/14 (year 2003) Good afternoon, I have water dripping into my dishwasher when it is not in use, approximately up to 1/2 inch over a few hours. The water collects at the bottom inside the dishwasher. I have to shut off the dishwasher water supply so that it does not overflow. Other than that, the dishwasher works perfect! Any idea as to what has to be replaced? Can I do it myself or do I have to call a technician. Thanks very much for your help.


HI. This type of issue will be the result of mechanical failure. This failure will be within the inlet assembly. Debris may be keeping the solenoid valve from closing correctly, thus, producing the steady drip a ... Dishwashers

Water does not come into the dishwasher. can hear the pump, the heater works, the indicator lites illuminate, but water does not come in. The water supply is hooked up and turned on, there is good flow to dishwasher connection, but no water inside the dishwasher during operation.


Hi,\015\012Usually the problem is the soleniod valve that lets the water into the dishwasher...\015\012\015\012here is a tip that I wrote that gives many more details about this problem...\015\012\015\012Dishwasher ... Dishwashers

Our kitchen drain clogged recently and water drained back into our VUD141 dishwasher. A plumber cleared the drain, and turned on the DW - which pumped out the standing water. But now, we have no water flowing into the dishwasher. The drain pumps, the heater works, but there's no water supply. The plumber who cleared the drain said he didn't DO dishwashers, and I cannot locate the owner's manual since we prepared for a move.


Hi\015\012\015\012 \015\012\015\012When the dishwasher won't fill and the water supply is on,\015\012then the issue is with the water inlet valve which is either clogged or\015\012blocked, you can try to clean it. If this wont so ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Our GE Profile Dishwasher is not working since today afternoon. The electronics seem to be working fine but the water supply does not start on pressing the start button. The dishwasher seems to go on with its cleaning cycle without water. We don't know how to fix this or to even check any plumbing/water supply problems. Please help.


OK First try this below....\015\012\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hu ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a JennAire jdb1090aws dishwasher. It's about 4 years old. The symptom is no water flowing through dishwasher. Approx 3 months after installation, the same symptom occurred. Tech resolved with float switch adjustment (no charge). Has run fine every since. I have not checked water supply, but doubt this is the problem (new water heater 3 months ago, sediment gone). I suspect the float switch is bad or out of adjustment. How do I trouble shoot float switch in dishwasher? Connect ohm mete


Hi,The procedure to test the float switch :-http://www.partselect.com/dishwasher+test-float-switch+repair.htmMost for no water entering the dishwasher, there are 2 main causes. One is the float switch and the other ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

LG dishwasher I have just installed an LG dishwasher. When I try to run the dishwasher it sounds as if it is getting no water. I checked the water supply line twice, and nothing is blocking it. The line is attached to the hot water under the sink and is open.


I bought a stainless steel Lg less than 15 months ago for 800.00and it stopped working. The manufacture said so sorry even though you didn't take delivery until the end of Jan. your warranty goes by purchase date. I would of been better of with a may ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

My plumber just installed a new water supply line for my dishwasher. Now the pump comes on but no water fills up in the machine. If I fill the bottom of the unit with water, it works just fine. Even though the water supply is ON, it does not pump water into the 'box'. Thanks, Art


You don't know how many times I've heard and found the shutoff valve off or partly turned off. Water entering DW is from line pressure not pumping. Items to suspect (again) the water supply valve (would'nt be the first time a new valve is bad). The ... Whirlpool 24 in. DU915QW Built-in Dishwasher

Not getting enough water flow into the dishwasher, suspect that a filter is clogged due to recent work on the waterline in the kitchen sink. Need to know where the filter might be located (on the dishwasher or on the intake valve before the connection to the dishwasher hose)? Also would I need to disconnect the water supply to pull out the dishwasher for access to such a filter.


You didn't specify a brand but most dishwashers don't have a water "filter." They may have an inlet screen at the water valve, which is typically located under the dishwasher. Generally, the lower front panel will have to be removed and you should ... Dishwashers

I installed according to guide, but dishwasher will not fill with water. Pump sounds much too loud to be normal. Wiring was checked three times for correct connections. Water supply was checked twice for water getting through, no leaks and water supply on. Drain hose is connected correctly and is connected to house drain.


You state the water supply is on.\015\012Have you loosened the compression nut at the dishwasher ell to see if you have pressure to the water inlet to the dishwasher?\015\012Remember the dishwasher will always run a little to make sure an ... Whirlpool GU2400XTP Built-in Dishwasher

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

My Siemens dishwasher SL34A sometimes makes loud vibration noises from the supply line at the water pump connection. I can turn off the water and back on it will quit, but sometimes starts again. And it does not matter how open or closed the supply line valve is either. I'm told it is likely the water pump, but this model has a combination water pump/motor assembly and I do not care to put another $230 into it. thx, TS.


... Siemens 24 in. SL34A006UC Built-in Dishwasher

Water drips out where the prtable dishwasher hooks up to the water supply. It is not the washer. It looks like it could be an o-ring inside the assembly that hook up to the water supply


... Whirlpool 24 in. DP940PWP Free-standing Dishwasher

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

I had a problem with my dishwasher popping the breaker. I opened the bottom and found burnt up wires. I fixed those and now the dishwasher stays on and begins its cycle (by draining) but the water is not flowing to the machine. It has supply, and I just now replaced the water inlet valve- no difference. The water was working before the breaker issue. I'm wondering if it is now something as simple as a clog somewhere since the washer sat unused for a month; or, if it is something more compli


I read your previous problem. This appears to be separate problems. The first was likely a loose wire. When a wire has a loose connection they build heat and can melt. The current issue would seem like the float switch is stuck. The float switch is ... Bosch SHU9925UC Built-in Dishwasher

I have Whirlpool dishwasher DWH B00. Now it starts as normal filling water for a couple of minutes. Then it suddenly starts beeping and pumps out all the water and just contiunes to beep. This will happen in all programs. We have studied the users manual and cleansed the filters as suggested in the manual, but this doesn't help. There are now problems with the water supply. The dishwasher is not used very much, may be just twenty times. In the start it worked normally, this problem suddenly


Hello & Welcome to FixYa If the sound is coming from the bottom panel then it is the motor that has gone bad and needs replacement. However, if you hear the sound from the control then it can be due t ... Dishwashers

The clean water fill will not shut off and water overflows from the dishwasher onto the floor. We had to turn off the water supply to the dishwasher to get it to stop.


Fill valve is shot , new one required \015\012\015\012Ps \015\012\015\012Does it still run when you remove the power if so the above applies \015\012\015\012If it shuts off then the problem sits with the pressure s ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Today, dishwasher started overfilling, and spilling water onto the floor. We turned off the water supply and let the dishwasher finish its cycle, turned on the water, started another cycle and it began to overfill and spill onto floor again.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. If the dishwasher is overfilling it’s ... Whirlpool 24 in. DU920PW Built-In Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1338 seconds