Having problems with your Dishwashers ?

Hi my hoover 6612 dishwasher does its pre-wash but then when the light for wash comes on it does nothing. I wondered if it might be a capacitor which needed replacing but I can't find one - any ideas??


Answers :

Try running the hot water in your kitchen sink until the dishwasher kicks on. \015\012--------------------------\015\012Simply turn the dial to another setting for a moment, turn the dail back to the Normal Wash and then press start again. Repeat the process with a different setting if it doesn't work the first time.
\015\012----------------------\015\012Press normal then heated dry
Three times in a row.
After the 3rd time all lights will go on. then press start .
\015\012\015\012\015\012\015\012
If the wash cycle doesn't starts or starts but does not completes then , check these:

Water-heating cycle
Timer
\015\012\015\012\015\012Water-heating cycle\015\012\015\012Many dishwashers heat the wash and/or rinse water to a higher temperature, as the cycle calls for it. In these cycles, the dishwasher pauses after it has filled with water, waiting for the water to reach the pre-set temperature. What happens next, depends, as follows:

\015\012
    \015\012
  • On some units, the pause is timed and the unit continues after the allotted time.


  • \015\012
  • On others, the cycle can't continue until the water reaches the higher temperature. If you have this type of dishwasher and the water isn't being heated (say, because of a problem with the heating element or thermostat), after the unit stops at the heating cycle, it never continues. When you repair the heating-system problem, the "cycle problem" is fixed too.


\015\012\015\012\015\012Timer\015\012\015\012Timers don't often fail. But if every other part of the dishwasher seems to be working properly and the timer knob seems to be stuck in one place--doing one function continuously--the timer may be at fault. Dishwasher timers can't be repaired. If yours is defective, replace it. 

\015\012\015\012
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi my hoover 6612 dishwasher does its pre-wash but then when the light for wash comes on it does nothing. I wondered if it might be a capacitor which needed replacing but I can't find one - any ideas??


Try running the hot water in your kitchen sink until the dishwasher kicks on. \015\012--------------------------\015\012Simply turn the dial to another setting for a moment, turn the dail back to the Normal Wash a ... Dishwashers

DWI612C wash cycle runs on and on and on. Believing to be a problem with water heating I tried putting a couple large pan fulls of boiling water into machine during wash cycle and this did move it on from wash to rinse. How do I replace the heating element I cant see it it is not in the dish washing compartment? I dont want to call out a repair agent as one can probably buy a new machine for what that will cost. Thank you.


... Smeg 24 in. DWI612 Built-in Dishwasher

Im replacing a frigidaire with a whirlpool and the problem I'm having is the electrical connections. My old Dw had two elec cords running to it. One small one that runs in the same direction as the drain and water hose runs the other is a slightly bigger elec cord that runs straight out the back of the cabinet unit and I cant tell where it goes. But it has on it anaconda w dutrax type nm 12/2 with grounding 600 volts.Do I need both elec cords for the new whirlpool or just one? All the online vid


Hello. Older houses offer all kinds of challenges. In the long run though, that is part of the joy of life. \015\012\015\012You need three things to hook up a typical dishwasher:\015\0121. The hot water source which goes to fee ... Dishwashers

Our dishwasher was taking in water, circulating it but not heating it up or moving through the cycle. My husband took the control panel off and there were some scorch marks on it so we got a new one. He replaced the control panel and the dishwasher went fine for one night. It heated up and washed everything perfectly. The next day when we put it on it was back to square one plus the lights on the control panel are now not working. Just wondered if anyone has any idea what we could do or are


Yes it's time to visit the dump ... Siemens 24 in. SE64A630GB Built-In Dishwasher

Poor washing The soap door opens but soap still in there after wash cycle. We got lower spray arm off and one plastic piece but can't get all the way to the pump. Pump appears to possibly be cracked so we suspect it needs replacing, but we can't get it out.


Before you suspect the pump and motor assy, do you hang the silverware basket on the front side of the lower rack or if not did one of the holders for the rack fall off and you replaced it? I have found that id the basket is hung on the rack that tal ... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

Our Kitchenaid dishwasher is nine years old and just started making a grinding noise during the wash cycle. It's coming from near the pump motor / capacitor area. How can I tell if I need to replace the motor or the capacitor?


You might want to check the wash pump inlet for junk ... Dishwashers

Hi I have the Kitchenaid dishwasher KUDIO1FLSS2 and all the buttons work except the two most important ones, the heavy and normal cycle. I had a service person out about 6 mo. ago and he said the control panel was about to go bad and replaced a fuse. He ended up coming again a week later and replacing the fuse with a stronger fuse. Now it's acting up again and I'm sick of hand washing dishes and don't feel like handing over another $300 or more if I can do it myself or maybe I just need to buy a


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

NEFF S4443 top spray bar not rotating, no water. Bottom spray bar rotates and sprays water. Checked and replaced fine/course mesh filters. Will pump to empty and refill on pre-wash (rinse). Seems the pump may have two outlets one feeding the bottom spay bar (nearest from of machine) and one just behind which feeds the upper spray bar. Running without spar bars attached (including mechanism feeding to bar, water is only being forced out of the from outlet. Any ideas before I start taking it apart


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Hi, the heating element in my Tricity Bendix DH200 needs replaced. I have purchased a new one but cannot work out where to locate the original. Any ideas as to how I would go about this? Thanks.


... Tricity Bendix 23 in. DH092 Free-standing Dishwasher

My Asko 1474 dishwasher doesn't stop washing. My expensive repairman said I need a new control board (8055479-R). Unfortunately they are obsolete. Do you have any idea where I might be able to acquire one?


... Dishwashers

My dishwasher spray arms were clogged with calcium buildup so I cleaned one and replaced the other. I also removed the fixed disc-shaped device underneath the lower spray arm and found the particle filter was clogged- so I cleaned it out. The dishwasher ran fine for a few times but then the filter clogged again, and again, and again. Now I need to make a routine of disassembling the parts to get at the filter every week because the filter no longer clears itself during the wash and/or emptying c


You may want to check your hot water tank. It may need drained and cleaned, Or you may have the rod in the tank disintegrating. Also check you water faucet areators to see if they have calcium pieces too. ... Maytag Dishwashers

I have a Kenmore Ultra Wash Dishwasher and the 3rd level spinner broke off. I have a new one and now need to know how to replace it.


You don't have to remove the top dish rack, but it might be easier unless you're flexible. To remove the dish rack, remove the "stop" clips from the front end of the tracks and pull the dish rack out.Remove the screw holding the water supply fe ... Dishwashers

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

I have a GE Profile Model# PDW7700G00CC that trips the circuit breaker when I hit the start button to begin a wash cycle. Green lights are on when I re-energize the unit but problem repeats when I hit start... Any ideas?? A blog pointed to a in-line Harness Transient Absorber or: "TransOrber". Also a Flood Switch and possibly the PC board... I can replace the parts... Just need to know what parts to order... Thanks! Steve


... Dishwashers

Door panel The panel on the door has rusted after 3 years. I need to find a replacement panel. Where can I buy/order one. I live in Gansbaai along the coast about 180km from Cape Town. The closest town is Hermanus. I am a good handyman and am able to fit the panel myself. This is urgent as my wife can not use her hands to wash dishes.


You will either need to have one made locally to match, or order one from the maker. try on line. you will need the model number and serial number to make certain that you get the right part.and in the meantime, you might need to do the dishes ... Indesit 24 in. D61 Free-standing Dishwasher

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

I have a maytag dishwasher mdb5600awb. it is about 5 years old. it does not clean anything on the top shelf for the most part. i took everything apart and found nothing that was clogged. we tried a rinse agent and that didnt help. for 460 dollars i expected more out of this. i also had the motor replaced 3 years ago. can someone give me an idea why i cant get my dishwasher to wash dishes?


Replace the dock at the back if it is missing a piece. That solved my problem with the top rack not getting clean. ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

We need to replace the locking ring in the bottom of our Asko 1716 dishwasher.(It's cracked) I can only find one kind of replacement ring for that,but it looks like the right size. I need to know if Asko uses one ring for more than one model of dishwasher?It's a 5" locking ring for the bottom well of the tub. Thanks for your help!


Only 1 size ... Asko D1716 Built-in Dishwasher

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

Hi, we have a Hoover HEDS668-80 dishwasher at work. The first problem we had was none of the programs would run this turned out to be a broken door lock. After replacement we managed to get one pre wash and one wash program to run, now when we try it, it starts but after 2 minutes the pre-wash and wash lights flash and the machine beeps 8 times. Can anyone help?


... LG LDF6810 Built-in Dishwasher

I have a Kenmore Ultra Wash Dishwasher model 665.16379301. The spinner from the top of the dishwasher has come off. I have a replacement part but need to know what is required to replace it. Do I need to remove the feed tube assembly in order to replace it?


... Kenmore Dishwashers

WATER SRAYER ARM BROKE OFF.HAS A SCREW TO TAKE OFF ARM, ALL I NEED IS ONE ARM TO REPLACE THE SPRAYER ON BOTTOM, DON'T NEED THE WHOLE UNIT..WHERE CAN I PURCHASE ONE?


\012Hi,\012That is not that hard to fix and you can easily buy the parts yourself online...Here is a tip that will help you with the online buying...How to Buy ... Jet Tech Systems Dishwashers

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

Model kudk031tbt3 I need to replace cover latch it pops out of the door during wash the dipenser door does open during wash. How would I replace latch


... KitchenAid 24 in. KUDP01DLBS Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1486 seconds