Having problems with your Dishwashers ?

''clean'' light flashing (whirlpool Dishwasher GU2300XTLS1 model)

\015 The ''clean'' light started flashing at end of ''normal'' cycle. Dishes somewhat clean but wet. No response from other buttons. When ''cancel'' button is pressed, motor sound comes on for a few minutes than it stops. Clean light still flashes. 7 flashed followed by a short pause.(if that means anything)THanks\015

Answers :

I had the same problem recently and a repair person came to my home to fix the dishwasher. He said he had to reset the control panel. He did this simply by making sure the soap dispenser door inside the washer was closed, then making sure the main dishwasher door was closed and locked. Then he quickly pushed the Heated Dry button and the Hight Temp wash button alternately. He said each button needed to be pushed twice within five seconds. After he did this all the lights on the control panel came on, then turned themselves off before the washer went in to a test cycle. This simple reset fixed the whole problem. Works great so far.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

''clean'' light flashing (whirlpool Dishwasher GU2300XTLS1 model)


I had the same problem recently and a repair person came to my home to fix the dishwasher. He said he had to reset the control panel. He did this simply by making sure the soap dispenser door inside the washer was closed, then making sure the main ... Dishwashers

Whirlpool dishwasher model number GU3600XTSY2 is flashing: The clean light is flashing! It's not the heater circuit either. It says the dishwasher is malfunctioned. Call for service to check heater circuit.Won't start at all.


The clean light sometimes flashes and just needs to be reset. To do so hit the keys in the following order. <Heated Dry> <Normal Wash> <Heated Dry> <Normal Wash> <Cancel>.The dishwasher will go through a cancel cyc ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


Do a "key dance" between normal and heated dry , going bak and forth six times. this will rester the heater fault. That is the clean light flashing code. Now you have to find the cause. Most likely is that there were suds in the last cycle or the do ... Dishwashers

I have a Whirlpool Dishwasher, model DUC600, serial # FS2202628. It suddenly stopped working and "clean" light is flashing. I turned the power off, hoping to reset it but the light is still flashing. Can you give me some direction? If it's a component gone bad, I can replace it if you can tell me which one. Thanks! Joe


... Whirlpool Dishwashers

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


If the dishwasher doesn't sense a water temperature increase, it will stop working and lock the functions (clean light flashes 7 times, all buttons are non responsive).To resolve this you will have to reset the console. Do this by closing ... Whirlpool GU2400XTP Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have a Whirlpool Quiet Partner 2 dishwasher from Lowe's model DV 1055XTVS. The "clean" light flashes three times in a row over and over and the "lock" light is one. None of the controls will work. I unplugged it and that did not clear the problem. How do I unlock/reset the controls?


I have a whirlpool quiet partner 2, its brand new. It leaves a filmy residue on my plastic ware. I use the finish detergent as well as the rinse and no luck. Whats the problem.???????? ... Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

Kenmore dishwasher, model 665.170 344 01. "Clean" light keeps flashing and will not stop. Have tried everything in the manual and the light still will not stop flashing.


Only reset you can do is unplugging power cord for 10 minutes.The control panel it is probably faulty and in need for replacement. ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Whirlpool dishwasher model Gu2548XTPS7, clean light flashes 7 times and won't start.


Check, if you have water in the machine, if yes, your control board could at fault ... Dishwashers

My whirlpool dishwasher model # is du1145 bought in 2006.problem clean light keeps flashing. says check heater circuit...how to repair?


... Whirlpool GU2400XTP Built-in Dishwasher

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a SMEG dishwasher. Can't find the model number on dishwasher or manual. Had two flashing lights and referred to manual - indicates a blocked filter. Cleaned that out, but now when I try to put it on "light" cycle (indicated by wineglass symbol), that light flashes (but no others as would indicate a problem).. All the other cycles work fine. Any ideas? Thank you!


Hi.If only the crystal light is flashing and no other light is on, then that is not an error code. Problem can be a temporary malfunction, or a defective control module or keypad.The delicate (crystal) light flashing with last ... Smeg 24 in. STX2 Built-in Dishwasher

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

Kenmore dishwasher, model 665.170 344 01. "Clean" light keeps flashing and will not stop. Have tried everything in the manual and the light still will not stop flashing.


If the clean light flashes 7 times, pauses then repeats...If the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non responsive ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Whirlpool dishwasher Clean light is flashing which says check heat circuit. I've reset board a couple times and run diagnostic. Element tests okay. Light keeps going back to flashing when running dishwasher.


... Whirlpool DU1055XTS Built-in Dishwasher

Whirlpool dishwasher Clean light is flashing, we just bought it last week and after the third wash, the Clean light started flashing and it won't go off, which stops it from doing anything else. User manul says to have it serviced, but that seems unneccessary. It doesn't seem to be draining completely, so there may be a knk in the pipe, which may be related, just not sure


The blinking clean light is an interruption in the dishwasher program that either indicates a malfunction, or a simple program glitch. The following link explains how you may be able to clear the blinking clean light problem: ... Dishwashers

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

I have a model 665.16032 dishwasher clean light is flashing


... Kenmore 24 in. 16032 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2534 seconds