Having problems with your Dishwashers ?

I have the kdw12st and recently it doesn't complete the wash cycle. An error code e1 flashes up at various times, not necessarily at the same point in the program.


Answers :

Andy,\015\012
\015\012First, heck for any leakage beneath and around the dishwasher.\015\012
\015\012If you are certain there is no leak, confirm that the drain hose has a rise of at least 20 inches as it travels to the drain. Which is almost certainly does, but triple check that.\015\012
\015\012Finally, if all else fails, the sump area - beginning with the filter - needs to be removed and the impeller needs to be inspected and replaced. Inspect the sump gasket.\015\012Good Luck!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the kdw12st and recently it doesn't complete the wash cycle. An error code e1 flashes up at various times, not necessarily at the same point in the program.


Andy,\015\012\015\012First, heck for any leakage beneath and around the dishwasher.\015\012\015\012If you are certain there is no leak, confirm that the drain hose has a rise of at least 20 inches as it travels to the drain. Which is alm ... Dishwashers

Dishlex global 460 fault.. Always stays on and makes a pumping sound while 'of' is displayed. Only way to turn it off is at the power point. Have tried turning it off at the power point for some time and re setting by pushing start & program at same time with no luck. According to the manual the code says "incorrect fill levet or time " and contact service for help. Any ideas?


... Dishwashers

I have a DWI 612C Smeg dishwasher I have an error code of the 2 right hand LED's flashing Have tried to reset the programmer (turn off, on then press program 4 times in 2 secs, wait 15 secs and turn off) This enables me to select a programme, but when the programme starts, after five mins it beeps and carries on making the draining pump noise and the programme never starts When I turn it off and back on I get the far 2 red lights flashing again Have looked for signs of blockages and can


... Smeg 24 in. DWI612 Built-in Dishwasher

PrimaLPR600 keeps giving us fault code by flashing 4 times and beeps continuously and doesnt wash properly, we have cleaned the arms but no joy


... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

I have a dish washing machine bauknecht model gsx 7988, when closing the frontdoor, the pump starts to run and a beeping sound is noticed, this beeping sound and automatic running of the waterpump happens on any selected program, when opening the door, the grren startligt is flashing two times fast,then a halve a second out and then flashing again two times fast etc.etc filter is clean, waterpressure is ok, eno other program can be started.pls help.


... Dishwashers

Whirlpool ADG7540 approx 4 years old (maybe a bit older) I have ran diagnositic check and the start light flashes 4 times stops briefly then flashes 4 times again over and over along with a continuous bleeping. When I put the dishwasher on any program I can hear the pump running but after a few mins the same flashing and beeping occurs although it sounds as if the pump is still running. I have taken off the pump checked for blockages and also checked the outlet hoses and spiggot, there are non.


Yikes, we have just identified this exact same problem tonight. If you've had any success with fixing it, we would sure appreciate hearing how. Best of luck with your machine ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Nordmende DFSN60 will not select programe,power etc ok.hold programe button and flashes P5 then 55,also EP & 188 flashes,close door and it runs through cycles but doesnt stop .when open door &


... Dishwashers

Tecnik DW2677 Hi, my dishwasher regularly starts to bleep after starting a wash program. When the door is opened it stops bleeping and the right hand light flashes 7 times repeatedly in sequence. By holding down the start and program change buttons together for a few seconds, it will reset. If you then close the door all is well for a few seconds the pump sound like it expells some water and then it starts to bleep again. The above process can happen several times before it decides to do what it


Check your water intake- i had the same issue - a leaky fitting wasn't supplying enough water to the dishwasher. had exactly the same symptoms you describe. fixed the leak, reset the dishwasher & it's working fine.\015\012\015\012\015\012\0 ... Tecnik TDW2677 Built-in Dishwasher

Kenmore elite 2 front loading washer model#110.45872400 It first flashed the code FH and then went to the running time is now flashing and it sounds like it is running but the cycle never starts and I cannot cancel the cycle by pressing pause/start two times. I have checked the water lines and the screens and cleaned out the drain catch below. what next


... Kenmore Dishwashers

2006 kenmore elite dishwasher 665-17263402- the clean light flashes 7 times , pauses then flashes again 7 times. What does that code mean? Cannot get washer to operate.


The blinking "clean light" is a common problem with some of the Kenmore and Whirlpool models dishwashers. The problem is usually attributed to water supply temperatures being too low when filling. Apparently, there are some issues with th ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

My whirlpool ADP 8540 starts, fills, then stop and flashes 6 times, pauses, and flashes 6 times repeatedly, until I end the cycle. What is this error code for? Can I fix it myself?


6 Flashes means water valve is switched on but flow meter senses no impulses (less than 10 impulses in 10 secs) and the water indicator is at a low level. Water Valve Closed or blocked.\015\012\015\012Water inlet valve defective. Flow met ... Dishwashers

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash


We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

ER Code Flashing. Frigidaire FDBB4365FC3 about 3 yrs old. Flashing lights on display. have reset the breaker multiple times. Got it to wash again but stops about midway with ER on display as well as Washing, Drying, Clean S flashing. Guy C.


... Frigidaire Dishwashers

Start button keeps flashing machine will not run on any program. I've tried holding down the start and time button which in the past has allowed me to restart the machine. This isn't working this time


... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

Dishwasher won't operate, just flashes "clean" 7 times-code?!


This may help in your situation. The following link explains how you may be able to clear the blinking clean light problem:http://www.f ... Kenmore 24 in. 16039 Built-in Dishwasher

Kenmore Elite 665.7696 dishwasher - "normal wash", "pots pans" and "cancel drain" lights flash on control panel. If power shut off for some time will work for part of load then start flashing again and stop. Is this a trouble code? If so, what does it mean?


Hi\015\012\015\012This error code appears when either the keypad(Part#1 in below link) or Control board(part#11 in below link) is faulty. You can reset the error codes sometimes by turning Off/On the power, however, this is not a permanen ... Kenmore Dishwashers

Hi there, I have a De Dietrich DVH610JU1 dishwasher, which has stopped working. Each time i try and set a program the machines makes noise as if its working but then stops with the 'End' light flashing blue very quickly and the 'Normal' program light lit up red. Any ideas? Regards Rosemarie


... De Dietrich 18 in. VW7451 Built-in Dishwasher

Whirlpool adg7460 dishwasher. when start a program runs for short time then beeps, light flashes 4 times


... Whirlpool Dishwashers

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

AEG OKO_FAVORIT 6281i dishwasher - error code 20 (Siphon blocked). Out of the blue after 6 years of reliable once-a-day family use, my AEG OKO_FAVORIT 6281i dishwasher started OK but about 3 minutes into the cycle began flashing error code 20. At which point there was a litre or two of cloudy water sitting at the bottom of the machine. Since then I've tried redirecting the drain hose into a bucket, after disconnecting it from the kitchen drain. Same symptom, and no outflow except what was al


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

Haier dishwasher CDW300SS beeping 10 times and 4 lights flashing,,, help The dishwasher will work, it fills, it washes and it empties, BUT will not start now, and the 10 beeps and the four lights flashing,, so wont restart and go throught the program... Is there some way of resetting the dishwasher to restart. help thanks. glenn


... Haier Dishwashers

Starts cycle, drains ok, then "intake/drain" LED comes on solid for 4 seconds, flashes 4 times, solid 4 seconds, flashes, etc. no water coming into dishwasher. DOUBLE CHECKED the intake filter its all OK ! how do i 'reset' the machine? Im pretty sure the sensor is goofed up and needs to be reset but i have tried holding various buttons, start, power etc, cannot figure out how to do it


... Miele G2430SC Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0793 seconds