Having problems with your Dishwashers ?
Dishwasher does not wash
\015 On all cycles the dishwasher fills with hot water OK, but the wash cycle does not kick in. It does drain OK.\015\012\015\012Any ideas??\015
If you are saying that in the wash cycle it fills and then stops it could be that your water temp is too low. Some models will stop to heat the water in the main wash before going into the agitate mode.
Repair Help & Product Troubleshooting for Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Foggy Glasses Glasses are very foggy after a wash cycle. There seems to be a heavy film on them. It can be scrubbed off with liquid soap and a brush. This started suddenly after I washed a baking pan in the dishwasher. The pan was very used and scratched before I loaded it in the dishwasher. After the wash, it was very rusty and there was rust on other dishes in the dishwasher. Could this have created some problem with the dishwasher, which is now affecting it's ability to wash? Thanks,
Yes i think this is the cause of your problemi suggest you run washer a couple of times empty but add soap ... GE 24 in. GSD2000Z Built-in Dishwasher
I set my dishwasher to wash last night (delay 2 hrs.) and I checked it this morning and it never washed. Yesterday, I had to turn off the dishwasher at the breaker box because it wouldn't reset. Now, the normal wash and heated dry lights are on, but it won't start. Also, it usually beeps when I close the dishwasher door, and now it won't even do that. We bought the dishwasher about a week ago. It a GE Profile dishwasher. Thanks, Chris
\015\012\015\012\015\012First off all try to close the door tightly with your hand till you hear a beep.dont force very much.\015\012as you mentioned that unit normally gives a beep when door is closed.but not it is not giving that beep w ... GE Dishwashers
The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.
Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers
Maytag dishwasher I have a Maytag dishwasher 2001 Mod# MD85100AWB - Ser# 25257529ZD. I can not get it to run again after the last wash. The lights (clean, rince only, light wash, heavy wash, heated dry) continue to blink and won't clear. I tried to power it down and that did nothing. Do you have a suggestion to what I can do to run my dishwasher again?. Thx, Richard
We have a model # 1385 Asko dishwasher. For the last few months we have found a film over all our dishes and pans washed in the dishwasher. We have found vinegar removes the film, but the need to constantly wash the already-washed dishes in vinegar to be defeating the purpose of using the dishwasher! We have used Cascade Complete for years, but we have tried different brands now, but nothing solves the problem. Can you please help us??????? Nancy Vocci
Hi \015\012Try running the hot water through the sink faucet, right before you start the dishwasher, so that hot water will instantly be there to run in the dishwasher, instead of it starting cold and having to warm up wh ... Asko Dishwashers
I have a Rebadged Siemens dishwasher model no. SE6TIE1GB / 13 TKD 795 / 2. When turning on, the dishwasher makes the "normal" noise of washing but after less than a minute it stops and refuses to wash anything. Ive tried pressing the reset button but no help. Worth mentioning, the night prior to that, I switched on the dishwasher before sleeping and when waking up at 5am, it was still washing so I manually turned it off and opened the door to find some water at the bottom of the tray.
... Siemens Dishwashers
No Water Coming Into SHU43C05UC/12 Bosch Dishwasher: We have a Bosch Dishwasher, model number SHU43C05UC/12. It has been working for more than 4 years, but yesterday I notice that although I hear a motor sound, there is no water in the dishwasher. The LED display on the panel seems to be working all right. I ran a diagnostic pressing and holding Power Scrub and regular wash button then pressing the on/off button. Got C1 at start then P0 and the Regular wash and Quick wash flashing on/off. How c
Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.
... Frigidaire 24 in. FDBB540 Built-in Dishwasher
Dishwasher hums I have a 2003 Kenmore Elite Ultra Wash Dishwasher model #665.17469300. I started the wash today. The water came in the unit and started washing then I heard it stop and it just started making a humming noise. I was afraid it was going to overheat or something so I cancelled the washed and it drained out. I started the unit up on a different cycle and the water came in the unit but did not wash it just hummed so I cancelled and drained it again. I did that on all cycles and the sa
... Kenmore Dishwashers
Whirlpool dishwasher This dishwasher quit in the middle of a wash cycle,we had to empty it and wash by hand. I thought that maybe the breaker to the dishwasher popped but when checked it had not .I then noticed that there are no lights on the electronic key board .Even when not in use there should be one red LED that is lit. It almost seems as if there is no power to the dishwasher. Is there some type of backup safety switch or breaker on the dishwasher itself that I could reset?
Fuse on control board. ... Dishwashers
I have a Kenmore Ultra Wash Dishwasher (Model Number 665.15634) that will not fill up properly. When I try to run a cycle (any cycle), the first thing the dishwasher should do is fill up with hot water. But in my case, my dishwasher fills for about 10 seconds, then stops. Then tries to fill again for about 7 seconds, then abruptly stops again. And this process goes on and on and on. The dishwasher never fully fills up nor starts the wash sequence properly. Once the dishwasher fills up, it
Miele dishwasher Hi I hope you can help. While we were away my daughter used fairy liqid in the dishwasher, and we did three washes to get rid of the suds and put the dishwasher through a cleaning cycle with a dishwasher cleaner. 'Inlet/ dreain is lit up and after the wash there is some residual water in the bottom. Is it mendable, please.?
You can go through this link http://www.miele.co.uk/Resources/OperatingInstructions/G%201142.pdf it contains the operational manual t ... Miele Dishwashers
Dishwasher model EIDW6405HTOA. MODEL # THO4259825. Installed past December and it doesn't wash. Things come out with spots, film etc. We payed a lot of money for this piece of junk. Talked to Electrolux in Atlanta, have two repear men and they said that as long as the water is running the dishwasher it's good. REALLY! Then why we have to WASH THE DISHES BY HAND, after the dishwasher finish the cleaning cicle. Costumer service in Atlanta it's as good as this dishwasher. We'll make sure to send m
... Electrolux Dishwashers
Westoint Dishwasher I have looked in the manual under troubleshooting tips, but didn't find anything on the problem. The dishwasher goes into cycle,but during the wash cycle it stops,makes alarm and the wash and rinse ligts come on. And now I can't even find the product on this site.Westpoint Dishwasher WQP12-9240. Thankyou My dishwasher is stopping at stage 2 of the programme after beeping once. Quite often the detergent flap doesn't open. Am at my wits end and threatening to leave home!!!! Th
Hi again,\015\012\015\012That should be OK. Just get in touch with your sales rep or his boss. Somebody there will be able to look up the record of the purchase. If they ask for model & serial numbers, you have them. You will find ... Dishwashers
My 2008 frigidaire 24" dishwasher model #FDB1050REC is not washing during the cycle. I have run the test cycle and the tub is filling up and draining but no washing is taking place during the wash cycle. The dishwasher has an electronic control board and therfore no mechanical timer. I put test leads to check for voltage on the power leads to the main washing pump, which I have already replaced with a new one, and I'm only registering a low voltage of around 10 or 11 VAC. With the cycle off I'm
If you have replace the motor and this did not fix your problem then yes replace the control board ... Dishwashers
I have a Bosch dishwasher model SHE4AP02UC/06, serial number FD901102579 that has been used twice since installation. When I select the Regular Wash cycle, the Regular Wash LED and the Active LED come on. The machine washes the dishes and then when it stops making noise. At that point the Active LED goes off and the Clean LED comes on with the Regular Wash LED. These LED's do not go off. There is no signal saying that the dishwasher is finished. Is this the way it is supposed to be operating or
Ya id say until u open the door after it has washed ... Bosch Dishwashers
Hi, my Ge profile dishwasher model pdw9280n00ss changes wash modes on it's own. This is a new problem, it was stuck on normal wash for the last year. It screwed up right after the warranty ran out. The start button and the heat all seem to work. I've seen it jump between the wash cycles on it's own while washing . Is it worth fixing, I feel ripped off on this expensive dishwasher!! Thx
... GE PDW9280NSS Built-in Dishwasher
Dishwasher malfunction I have a Kenmore Ultra Wash Quiet Guard 3 dishwasher. One day, I found it with a blinking green ?clean? light. I went online to search for the manual, almost impossible to locate. Found a website where another using said to hit a 4 button sequence of ?heated dry? ?normal wash? ?heated dry? and normal wash. After this sequence, all lights went on and something that looked almost like a ?demo? sequence began (not sure now what that was). I hit ?cancel/drain? and it proceeded
Hi,The flashing light indicates that the control did not sense a 3 degree temperature rise with an 8 minute test. There are many reasons this could happen with a working heater. I put together a page that shows the reasons and you might b ... Kenmore 24 in. 15689 Built-in Dishwasher
We just bought a new Bosch dishwasher, I've never washed baby bottles in the dishwasher before, does anyone know if it is a "no-no" even in a Bosch? I have always thought that any baby bottle, (we use Dr. Browns), was not meant to go through the dishwasher, but I'm TIRED of hand washing them! Any experience/research with this? Many thanks!
Hi, I have now a 4 year old. My wife and I have always put the bottles in the dishwasher. It will be fine. ... Bosch 24 in. SHU43 Built-in Dishwasher
On my Kenmore Ultra Wash Dishwasher model 665 the Normal Wash light is blinking even though the previous cycle finished successfully. Also I can't start the dishwasher -- it doesn't respond to any of the buttons. I have powered it off and on and the Normal Wash light comes back on within 5 seconds of restoring power.
Http://appliancejunk.com/forums/index.php?topic=2933.0\015\012\015\012\015\012\015\012Hi. please find above your service and repair manual, bel ... Dishwashers
Dishwasher problem It is a "classique" dishwasher , about 8 years old, but used only about 50 times max. The dishes are not getting out clean - the washing powder is smeared over them. Most of the dish washing powder (or tablet, tried it both) is not comming out of the powder compartment, despite the fact that we find the compartment open when the washing cycle is done. Sure it is just a "smal quick fix thing" but have not idea what it could be. Pleaseee help!
Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella
Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher
Westinghouse undercounter dishwasher. after shutting door with latch, comes on when dial knob turned to selected wash. was taken out to redo floor underneath. after being placed back in position, did at least 2 loads fine. now after dial knob gets to selected wash, dishwasher light comes on and i can hear the motor try but then starts clicking. there is also water at the bottom inside the dishwasher
This seems to be a drainage problem, obviously. There may be some food debris in the drain tube where it connects to the drain pipe. It would be easy to detach and do a visual check, and see if you can clear the clog. Also, try to s ... Dishwashers
My whirlpool dishwasher adp4407 is not washing properly when i open the door thinking its finished a wash the soap tablet has not dissolved and is on the bottom of the dishwasher and sometimes its not emptied the water also the red light is constantly on i did not know you had to put salt in a compartment on the bottom of the dishwasher how much salt are you suppoosed to put in this compartment.
Dishwasher makes grinding noise during wash cycle (after pre-wash). noise persists for 15-20 minutes. It seems as though the inlet valve doesn't open during this phase of the cycle. adding water to the dishwasher manually eliminates the noise and water circulates through the wash arms. I'm trying to determine if this is a controller issue or a valve/pump issue.
Water-inlet valve\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012\015\012\011\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\01 ... KitchenAid Dishwashers