Having problems with your Dishwashers ?

No water entering machine - mains supply OK

\015 Model No ADP4731WH Machine appears to be working OK but no water and after a little while LCD reads F4 and start light is flashing.\015

Answers :

On a Whirlpool ADP4731 dishwasher, try this...\015\012
Double check that the under-sink valve is open, providing hot water to the dishwasher.\015\012
\015\012If it is, the water inlet valve should be checked for proper operation.\015\012
\015\012The F4 error code means "drainage fault" which should be checked after the water inlet problem has been resolved.\015\012
\015\012Good Luck!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No water entering machine - mains supply OK


On a Whirlpool ADP4731 dishwasher, try this...\015\012Double check that the under-sink valve is open, providing hot water to the dishwasher.\015\012\015\012If it is, the water inlet valve should be checked for proper operation.\015\012 ... Dishwashers

Power to the machine, removed the water supply line and there is water at this point but sometimes the water will not enter the machine. The unit is 14 months old.


\012Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Trouble ... GE Dishwashers

I DISCONNECTED WATER SUPPLY TO STOP LEAK. NOW WHEN I TURN ON THE MACHINE NO WATER ENTERS, IT JUST HUMES. THE WATER SUPPLY IS ON.


... Maytag 24 in. MDB8750A Jetclean II Built-in Dishwasher

Water supply was turned off at the mains when the machine was running. Machine is telling me to check water.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the\015\012cycle doesn't complete, check these:\015\012\ ... Bosch Dishwashers

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

Only a small amount of water enters machine when you start normal cycle. I took off water supply line at inlet valve... screen is clean, water preasure is fine.


You might have a bad water inlet valve, when triggered the inlet valve opens up to allow water to enter the machine, it's usually located behind the lower kick plate in either the right or left hand corner, if it's defective it would need to be repla ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hi there There appears to be no water entering the machine. Have checked the inline filter + the main machine filters, all clear. Machine all lights up as normal but will not start cycle


... AEG 24 in. Favorit 44050 Built-in Dishwasher

Hi there,i have a brand new but 3 year old,diplomat 8332,just fitted it,it does the pre was ok,pumps out the water,goes to next stage,you can hear water entering the machine,shortly after it has started the main wash,it starts to cut out intermittantly,then F2 code appears,and a bleep.i have taken the lower panel off and checked for leaks and to see if the valve was free,all ok,also relay click in front panel,safety cut out ? any ideas please.


... Dishwashers

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

My SE53200GB/01 fails to input water. I have checked the inlet supply hoses and filters and they are clear. I have tried different programmes and they all activate but the water fails to enter the main chamber. Any ideas what may be the problem. Could the Aqua-Stop mechanism have kicked in and if so, how do I rectify it? Thanks


Your aquastop system is activated :deactivate by turning off the water supply, running the dishwasher so \012that it is expecting to fill (if you hold the grey square box at this \012point, you should feel it slightly vibrating, which is a good sign ... Siemens Dishwashers

My Diplomat HJA 8630 dishwasher has stopped working. Put cycle on machine filled with water then no power and can not drain dishwasher. Fuse checked and changed, so not mains power supply. Any suggestions??


... Dishwashers

Zanussi ZSF 6126. With door shut and knob turned to position A (or any position) only the WASH LED comes on. DRY and END are extinguished. No water enters machine. Supply is OK. Filters are clean. Any clues please?


... Zanussi Dishwashers

Power washer - model jcb-pw20tss. TSS=total stop system. seems to be ''stuck'' on my model. Can you suggest method to free up and restore pressure which will allow me to switch on machine again. Mains electric =OK Fuse = OK Connected to water supply =OK


... Pressure Washers

No water will enter the dishwasher, There is no problem with the water supply or the supply line. The water flows from the supply line to the dishwasher connector but does not enter the dishwasher.


The water-inlet valve lets water enter the machine. Make sure it's not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if you get power to valve when unit is put into operation ... KitchenAid Dishwashers

I have a Bosch SHU43C. I have a leak it seems to come out from the door. I removed the front panel. Inspected the seal and all seemed smooth and not damaged in any way. So I decided to run the machine. Waited for a few minutes and the water leaked from both corners at the same time. The water settled in the rubber trough under the door. After a few more minutes the water leaked over the trough and onto the foor. Is there to much water entering the machine? What limits the water entering


... Bosch 24 in. SHU43 Built-in Dishwasher

No water entering the dishwater. water supply is hooked up and water supply valve is in the open position. Could this be a water pump problem or is there a cut off valve entering the back of the washer that could be in the closed position?


No cut off on washer check float switch make sure its free check water valve make sure wires are on it and water getting to it ... Kenmore Dishwashers

On no programn does water enter machine


... Tricity Bendix 24 in. BDW53 Free-standing Dishwasher

Whirlpool dishwasher DU945PWPQ2 four year old machine - never used. Water lines are attached properly and are clear. When dishwasher is turned on the wash cycle light turns on. cycle completes but water does not enter the machine.Water does not enter the machine.


... Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

Bosch 24in. SGS69LO2 Logixx Our machine runs but there is no water coming into the machine?have removed pipe to check water flow,ok, have removed the filter for the inlet supply,clean.have cleaned all filters and replaced, reset the programs, but still no water into machine.


... Bosch 24 in. SGS69L02 Logixx Built-in Dishwasher

My Bosch Classixx (about 10 years old) dishwasher won't fill The problem has only started since I pulled it out and cleaned! The programme sounds are as normal but no water enters the machine. I detected a small leak on the inlet pipe and tightened that. The machine drains when I add water manually though it has made a lot of gurgling noises for some time now when draining. When tipped on its side water comes out of the bottom of the machine (not entirely clear but not dirty either). When upri


... Bosch SHU9915UC Dishwasher

Kleenmaid DW8 top washer does not operate. Apparent blockage in the water supply tube which runs up from the bottom water supply. How do I remove the bottom assembly comprising the main filter, waste trap and micro filter? I appears that these must be removed to access the water supply tube mentioned above.


... Dishwashers

Some guys at the church was using this haracher 4000 psi, I was call and was told the machine stop working and would not crank up.I use a next machine to finish the charity jobs on saturday. Sunday the machine starts up but when I connect the garden hose and turn on the water it did not comes out, where the VALVE HOSE THAT GOES TO THE WAND ABOVE THE UPLOADER, I open every bolt and water comes out except the wand valve, pump was plush out and sprayed out, so we know that water enter the pump


Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuc ... Karcher Pressure Washers

My plumber just installed a new water supply line for my dishwasher. Now the pump comes on but no water fills up in the machine. If I fill the bottom of the unit with water, it works just fine. Even though the water supply is ON, it does not pump water into the 'box'. Thanks, Art


You don't know how many times I've heard and found the shutoff valve off or partly turned off. Water entering DW is from line pressure not pumping. Items to suspect (again) the water supply valve (would'nt be the first time a new valve is bad). The ... Whirlpool 24 in. DU915QW Built-in Dishwasher

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1268 seconds