Having problems with your Dishwashers ?

Kenmore Elite 13133K started to fill, the door was opened. Now it won't resume, drain or fill, the geen light is flashing. I turned the power supply off for 5 minutes and the problem still exists.

\015 Just installed Kenmore Elite 13133K started to fill, the door was opened. Now it won't resume, drain or fill, the geen light is flashing. I turned the power supply off for 5 minutes and the problem still exists.\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore Elite 13133K started to fill, the door was opened. Now it won't resume, drain or fill, the geen light is flashing. I turned the power supply off for 5 minutes and the problem still exists.


... Dishwashers

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

Have a Whirlpool Dishwasher 6ADP 5540. Starts cycle - fills water then about a minute into it the start buttons flashes 6 times and will not continue on. Very rarely, the cycle does continue on. Have turned off at the main switch. But still have this problem. Look forward to your reply. Cheers, Jodie


Hi Jodie,\015\012\015\012An F6 fault code - indicated by the green light flashing in sequence next to the start button - is indicative of a water inlet problem. \015\012\015\012First of all check that the water tap the dishwah ... Whirlpool 24 in. ADP6940 Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

I have a hotpoint LFT04 dishwasher. Recently it tripped the power supply, and now when we start a cycle after a few minutes it stops and the lights on the power button and cycles 2 and 4 flash constantly. If the power button is turned off and the door closed, after a period of time it starts up again automatically. Any ideas appreciated.


... Dishwashers

Intermitttent beeping on bottom drawer of dish washer no error code only cycle to work all the way through is rinse cycle. Have turned off power supply over night did not fix problem. When you press pause button restarts for about five minutes then beeps again. No problem with top drawer. All inside cleaned using correct powder and rinse aid.


Panel control board Call Encompass Parts 1-800-638-3328 ... Fisher Dishwashers

My cda CW195/1 dishwasher keeps running for 5 mins then beeping, salt indicator was flashing but have now filled up and the indicator has gone off, i have cleaned the filter, turned off and on and tried on a high setting but it still it beeping like there is a problem!


I am having the same problem. It's a piece of rubbish. ... Dishwashers

We have a Maytag Model MDB6100AWW that will not start. All Lights are flashing. We turned of the power supply hoping it would reset, but to no avail. Please advise what the problem may, and what is the fix.


... Maytag 24 in. MDB6100A Built-in Dishwasher

Lights on the control panel flash. Dishwasher does not come on. Tried reset and turning the power off. Problem still persists.


... GE Nautilus 24" Built-in Dishwasher

I have a Kenmore Elite Ultra Dishwasher and the cleaning light is flashing. I have tried pressing the start/resume button and closing the door within 3 seconds. I am not able to turn on my dishwasher. I have tried turning off the power for 20 minutes but when power was restored the green light continues to flash and the dishwasher will not work. This machine was installed in May 2008. Help!


If the clean light flashes 7 times, pauses, then repeats...When\015\012the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non ... Dishwashers

Dishwasher is just less than 1 year old. it doesn't respond to attempts to turn on. I turned off the power at the box and back on after 10 minutes. it worked. then the same problem returned. now it wont turn on at all. I checked all the connections I could and they seem fine. I know it is getting power. My guess is that something is wrong with the computer system. any ideas?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Maytag 24 in. MDBH950AW Built-in Dishwasher

Washer is stuck in mid cycle. Have turned of power as the current monitor light is red. maybe electrical problem. when i turn power on again the lights flash on for a few seconds then turn off again.but nothing works.


Step1:Use the diagrams in the manual to locate the food trap. Remove the top\015\012of the food trap and empty out any debris inside. If there is standing\015\012water in the bottom of the dishwasher, watch to see if the water level\015\012rece ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

I have a KitchenAid dishwasher, model KUDP02FR. The "normal" cycle light is flashing. When I push "cancel" or "resume/start", they start flashing as well, but the dishwasher won't start. I turned off the power and turned it back on. The "normal" light still flashes, but when I press "resume" it all starts over again. Any ideas? I can't find this in the troubleshooting guide I have. Thanks.


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid KUDI01TBK Dishwasher

I have a AEG OKO_ FAVORIT 4040 dishwasher which has had very little use despite its age. The problem is that the switch that detects an over-fill is activated all the time and the pump continues to try and empty an already empty dishwasher even when the main switch is turned off, the only way to stop this is to turn it off at the power point I have had some sucess deactivating this switch by tilting the dishwasher forwards however because of the angle it sometimes overflows when filling. The ma


Hi there,This could be a problem on the control board of the unit. It could be faulty and need replacement or you may try to access the board and try to clean it.Make sure upon doing this all electrical connection to the unit ... Dishwashers

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

Hello, I have a beko 2341 fs dishwasher and I have a problem with it. When i turn it on to wash the red light above the "salt" part comes on. Ive filled it up with salt twice now and its still coming on when i turn on the dishwasher. My cutlery is starting to rot and glasses and coming out very cloudy . what could the problem be?


... Beko Dishwashers

I have a Frigidaire Gallery dishwasher model number FDB989GFC2. All of the indicator lights on the right side are flashing (Controls lock, add-a-dish, washing, etc.). when buttons are pushed I get no response. Have tried turning off at circuit breaker for 1 hour, when powered back all lights still flashing and still no response from pushing buttons. Any ideas?


You need to rpelace the electronic control board ... Frigidaire FDB989GF Dishwasher

Hi - my Viking dishwasher has developed a problem where the pump runs continuously, whether the power switch is ON or OFF. After the power is turned ON, the troubleshooting guide indicates that there is too much water in the dishwasher. (One of the pot symbols on the display flashes continuously to show this indication.) I am unable to switch between programs, e.g., from quick rinse to pots & pans. I cleaned all the filters to no avail. I had to secure the circuit breaker in order to turn t


If you open the kick plate, you'll see the pan below the motor and check for leaks. The leaks will trigger the sensor to pump water out. Once you dry out the pan, the pump motor will stop and you should be able to reset the program. ... Viking DFUD042 Built-in Dishwasher

I have an H62 Hobart commercial dishwasher. I had it on fill to start it up. There was a loud pop while it was filling and now it has stopped. The power light is still on but the dishwasher will no longer fill. Where should I start looking for the problem. Would it be a fuse that popped?


... Dishwashers

Hi, I have a Miele G681 dish washer with an intake/drain light problem. I've read all posts about similar problems I could find both on this forum and others but I'm afraid I still can't figure my problem out. The intake/drain light starts blinking mid way into the dishwashing process. The dish washer fills up, rinses, drains, water is hot, everything seems to function just fine. Some time after the tablet drops from its door mounted container, and the time estimate reaches 46 minutes r


... Dishwashers

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


... Frigidaire Dishwashers

Kenmore elite clean lite is flashing won't shut off.unit won't work modle #66516912001 serial#fk4402228.it flashes 7 times over and over.i shut off all power turn back on still flashes .i replaced electric board in door panel new button panel


I have a service bulliten on this if you will email me at [email protected] ill send it to you its too big for here ... Dishwashers

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1861 seconds