Having problems with your Dishwashers ?

I have a Kenwood KDW12ST3A that intermittently shows E1 Thank you in advance for your help.


Answers :

Hi\015\012
\015\012E1 means no inlet pressure. Sometimes fault code shows if machine takes too long to fill. Kindly check for blockage in inlet pipe. Also check if water inlet is not filling and check if the water outlet valve is opening and there is sufficient water pressure.\015\012
\015\012
\015\012Please do rate the solution as "FixYa" and revert for any clarifications.\015\012
\015\012Thanks\015\012
\015\012Rylee
On my machine the plastic filter that you will find when you remove the water inlet hose "from the machine" was blocked. Use a pair of pliers to pull the small plastic filter out and wash it under a tap. On my filter it was the sides of the filter that was blocked, which you will not see until you remove it.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenwood KDW12ST3A that intermittently shows E1 Thank you in advance for your help.


Hi\015\012\015\012E1 means no inlet pressure. Sometimes fault code shows if machine takes too long to fill. Kindly check for blockage in inlet pipe. Also check if water inlet is not filling and check if the water outlet valve is ... Dishwashers

Kenwood KDW12ST3A Kenwood Dishwasher 18 months old intermittently shows E1 Thank you in advance


E1 indicated long filling time. Perhaps the inlet filter has clogged. Check the inlet pipe and tap(faucet in usa). ... Kenmore 15762 Dishwasher

I have a Kenwood Dishwasher KDW12ST3A. P1 cycle stops after about 40 minutes and shows on the screen an error code of 'E3', Not sure what this means as I have mislaid manual. Can you help please?


... Kenmore 15762 Dishwasher

Kenwood kdw12st3a does not drain. Flashed e4. Emptied, cleaned filters and poured through boiling water. Not improved. Still water in bottom although did complete cycle without flashing error code that time. What parts could be faulty please? Am prepared to have a go at replacing if not too difficult. I note that I can purchase most parts from Kenwood etc. Many thanks!


... Kenwood Dishwashers

Hi I have a Whirlpool ADP60001X, 4 years old. Problem - Error 4 showed so I fixed that then started another cycle and it shows up error 1 now - what does that mean & how to fix - help would be appreciated thank you


... Whirlpool 24 in. ADP6940 Dishwasher

My aeg favorit integral dishwasher is flashing 20, and there is water still in the bottom that will not drain away please help. and every time i put the dishwasher on it starts but after a couple of minutes it stops beeps intermittently and says code 20! please help thanks


... AEG 24 in. Favorit 60830 Free-standing Dishwasher

I also have a dishwasher (AEG Favorit), and it does not heat the water anymore. It worked fine for last 3 years, and all sudden, it only washes dishes with cold water. Could you please help to solve this problem? The hot water line is fine and I do have the hot water to the sink next to the dishwasher. Thank you in advance for your help.


... AEG 23 in. Favorit 44070IW Built-in Dishwasher

GE Quietpower 3, GHDA480N10WW. Need help. Dishwasher has worked fine. used it last week. Today, when I pushed the buttons, it did not turn on. The power is hooked up, breaker has been checked and re-set but buttons do not activate at all. Acts as if there is no power at all after a week of no activity. Any help would be appreciated. thank you in advance.


... General Electric Adora GHDA670N Built-in Dishwasher

I have Candy dishwasher A9010 SMART, 7 years old. Two minutes after pressing the start button, it stops and shows error code E4. Thanks in advance


... Candy Dishwashers

Kenmore Dishwasher model # 665.16602300 Control panel push buttons do not function except cancel and delay buttons. No other buttons work at all. Thanks for help in advance Rich Bussmann


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have purchased a Dewalt 3800 PSi cold water machine and it keeps shuting off this is the second machine in 2 weeks. I took the 1st one back bc of the same problems. Any advice?I believe hot water was being used occassionally also if that helps with your answer. Thank you in advance!


Check to see how hot the water can be, ti should be on the unit or in your book. also your amps should be no less than 15amp, long core can over heat the motor. if your unit can't handle hot water it will melt the valves ... Dewalt Pressure Washers

John Lewis JLDWW906 Slimline Dishwasher, White. Hi all, have a problem with my dishwasher. The display is showing an error of i30. Can't reset it. Have checked the filter etc and everything seems fine. John Lewis technical advice not open till Monday and engineer can't come till Thurs. Help? Thanks


... Dishwashers

I have a kenwood dishwasher kdw12st3a i cant find a user manual online and i need to know where do i put the rinse aid and the salt thanks robert


You do not need. all you would probable need is jet dry which can hang on the top rack or put in the round hole by where you put the detergent. ... Dishwashers

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

I have a kenwood kdw12st3a dishwasher (just out of warranty grrr). When turning on I am unable to select a programme. It beeps and shows "---" but nothing happens when selecting the program button. I have checked the door catch, seems fine. Any ideas please?


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Can anyone help me with my fisher and paykel DD603 the top draw is showing F1. fault 1. thanks


When F1 is showing up then there is a leak. The leak is causing by the top lid seal not close down tightly to the opening tube surface groove. Pull out the tube, put in tower in the bottom housing accessing from the left side. Only this side you can ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My Bosch SHI4306UC dishwasher will not stop running in the rinse mode. I was wondering if it will not advance because the heater is not working well enough to increase the water temp to complete the cycle. Is this most likely the heating element and something that can be fixed by a homeowner? Thank you for your help, Steve


... Dishwashers

I HAVE A KENWOOD KDW12ST3A DISHWASHER AND IT HAS THE E4 ERROR CODE THEY DID NOT GIVE ME A MANUAL WITH IT CAN YOU HELP


I hav a kenwood kdw12st3a and the e4 code came up and it said in the manual it had overfilled but it did'nt tell you how too fix it can you help ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Creda ID160 Hi wonder if anyone can help. I have the above dishwasher and it seems to be stuck as if drying..... i have switched it off by the mains over night to see if this resets but nothing.... thanks in advance


... Creda 24 in. DWI34 Built-in Dishwasher

I have a Kenmore mod.#685.16029402 Type 575 D, It will not start, and it's stuck with the green clean light flashing all the time. Please help. Thank you in advance Randy


... Dishwashers

I have a Whirlpool dishwasher model GU400XTPQ3 and it stays on the clean cycle and will not advance despite saying it has 2 minutes left? Please help. Thank you!


Important information about dishwasher cycles:\015\012\015\012\015\012Normal cycle time is anywhere from 1.5 to 3 hours long.\015\012\015\012A delay automatically occurs in some wash and ... Dishwashers

We have a kenwood kdw12st3a dishwasher - ever since we have had it, it has been nothing but trouble. It constantly flashes e4 so we have tipped it and drained the water out of the bottom (as advised) and it works for a couple of days then happens again. Now it refuses to work at all - cant set a programme - nothing at all - please help!


To clear the fault you need to remove the two baskets from the dishwasher.Slide it out from under the worktop and lean it forward to about 45 degrees.If it is already full of water, turn on the power whilst pushing the program ... Dishwashers

Bosch My bosch dishwasher shows an "F" on the display when started. It sounds louder than usual but the cycle doesn't start. I made sure there were no obstructions, debris, etc but no help. Thanks.


F is fill fault to much or not enough water or water in the sump white plastic base the f code will not go away until you solve the problem when the f code shows up the drain motor will run all of the time ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

Where can I get the instruction manual for a Bosch Classixx Dishwasher SGS53C12UK? I have bought a second hand dishwasher that has only been used for 6 months. The programme works fine but when I go to use it again - check water shows on the display. I have to tilt the machine back as water is stored at the base of the machine, surely this is not normal? It there a simple solution to this or alot of cost involved with a new part? Any help would be much appreciated. Thank you.


... Bosch Dishwashers

Sporadic pressure The pressure on my washer cuts in and out continuously, two seconds of power followed by two seconds of nothing. I have tried to take the lance off to see if it is blocked, but it seems to be stuck fast. Any help would be welcome, thanks in advance.


OK. Pulsing on and off is quite common. Unfortunately, it can have several possible causes.\015\012\015\012If the  machine pulses while you are squeezing the trigger, and there is water coming out of the jet, then most probably the jet is ... Karcher K2.26 Electric Power Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1046 seconds