Having problems with your Dishwashers ?

Suddenly stopped working - won't run on any cycle.

\015 We have a Kenmore dishwasher - ultra-wash quiet guard plus model #66515705891 - it suddenly quit working. None of the cycles will work. What are some possible solutions?\015\012Thanks\015

Answers :

First check the electrical supply. I have seen dozens of dishwashers which did not have the hot wire connected tightly enough (inside the connection box behind the lower panel). Sometimes the loose wire caused the breaker to blow. If you have control lights but the dishwasher will not start it could be a bad door latch saftey switch. $10 part, cheap. Hope this helps, Ken
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Suddenly stopped working - won't run on any cycle.


First check the electrical supply. I have seen dozens of dishwashers which did not have the hot wire connected tightly enough (inside the connection box behind the lower panel). Sometimes the loose wire caused the breaker to blow. If you have cont ... Dishwashers

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

Dishwasher stopped cleaning but appears to run through cycles. Possibly water starved. The bottom "sprayer has some water coming through the holes but is not spinning, (although spins freely by hand). The top and middle "sprayers" definately aren't functioning. Stopped working suddenly, (not a gradual change).


HI. I agree with your assessment. There may be some sort of blockage within the hose assembly. I recommend to inspect all hoses that correspond to the actual recirculation pump. Check the drain hoses as well. ... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

KitchenAid KUDI10FL dishwasher- The door spring system broke and I repaired it, but now all of the sudden the dishwasher will not start. The door may have been dropped a couple of time before the spring system was repaired, but it did not hit the floor, just a hard sudden stop. All of the cycle setting lights come on when they are pressed except for the start button. Just before the start button stopped working the dishwasher started by itself or started several hours after cycle selection had b


Hi- It is possible that the door latch is not completely engaging. If the door dropped the hinges may have bent a little thus preventing a good contact with door switch. Try pressing and holding the door shut, hard, and pressing start. If that wor ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a bosch smu 2000 series dishwasher. it has always worked well with no problems but then all of a sudden a week or so ago, the water stopped coming into the dishwasher to wash the dishes. the faucet and all other water areas continue to work w/o problems (i.e. bathroom, shower etc). in attempting to use the dishwasher, the entire cycle seems to be working, i initially hear what sounds like an initial water discharge when the cycle first starts and during the entire cycle it sounds like it


... Bosch Dishwashers

The dishwasher will start to cycle. I can hear the water begin to run. I hear a click and at the time the dishwasher should start to run the cleaning cycle. During the cleaning cycle the dishwasher will stop working. The dishwasher is silent. The timer will continue and the water will drain out at the appropriate time.


This is probably okay, you have clock like motions running the motor electric contacts. There needs to be a delay between some cycles or shorting will occur. The motor on some designs, for example. is reversed to pump out water. to have this work lon ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

I have a MDB4630AWS1 series dishwasher that is only a couple of weeks old. Suddenly, it now starts the wash cycle but then the Cancel/Drain light turns red, and it drains and stops the cycle. Check for items blocking the sprayers and looked for anything clogging the interior. It does this with all the settings. Seems to work for a few minutes, but then it just drains and stops. Any help would be greatly appreciated.


... Maytag MDB4630AWS Dishwasher

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

I have a kitchenaid dishwasher model KUDS01FKSS0 which is not running. For the past 2-3 months it occasionally stopped mid cycle with water still at the bottom of dishwasher but eventually resumed working. Now it just doesn't run any more and there is water presently in the dishwasher tub). The user interface part (keypad) seems to be working. I can press the keys and the corresponding LED would light up. However after I close the door, nothing happens. There is also no noise what so ever. Any i


THE MOTOR SHOULD MAKE NOISE IF ON, CHECK THE MOTOR OR TIMER. ... KitchenAid KUDS01FKSS Dishwasher

Wont run I have a Kenmore QuietGaurd2 it will not run at all. It filled up with hot water, then it quit working. It wont even drain the water out or cycle. Nothing is happening, whats wrong with my dishwasher??


... Kenmore 24 in. 15992 Built-in Dishwasher

Dishwasher suddenly stopped working at start of cycle. opened door to see why water had stopped, there was small amount of water in bottom, it has now drained. turned it off and on again to restart cycle but now nothing is happening


... Bosch SHV4803 Dishwasher

Dishwasher works if I hold it in and will run cycle then stop. I push and hold it in again and it will run an other cycle. Is this reparaable?


Hi there,\012Well problem seems in the door switch, it is important because, if it's defective, the dishwasher won't work at all or work only when you press the door. To reach it, you need to remove the control panel cover, or sometimes t ... Maytag Dishwashers

I have a kitchenaid dishwasher model KUDS01FKSS0 which is not running. For the past 2-3 months it occasionally stopped mid cycle with water still at the bottom of dishwasher but eventually resumed working. Now it just doesn't run any more(and there is no water presently in the dishwasher tub). The user interface part (keypad) seems to be working. I can press the keys and the corresponding LED would light up. However after I close the door, nothing happens. There is also no noise what so ever. A


... KitchenAid KUDS01FKSS Dishwasher

Stops mid-cycle I have a MDB7100AWB that has been working fine for the last 7 years. Now all of the sudden it will not complete a wash cycle in any mode (including auto clean). It consistantly stops at 85 on normal wash & at 65 on light wash and then clicks/buzzes about every 3 seconds, like it wants to continue - but never does. Any clues as to what to try? Is 7 years all I can expect to get?


Hi SaviorSound,\015\012\015\012I'm Harvey the Master Plumbr.\015\012\015\012Your question is: You have a MDB7100AWB that has been working fine for the last 7 years. Now all of the sudden it will not complete a wash cycle in a ... Maytag MDB7100AWB Dishwasher

I have a GE Profile Eterna series triton dishwasher. When it gets t rinse cycle, lights go out and it keeps rinsing. Buttons stop working and it won't stop or reset. If I unlatch door and wait for hours lights may come back and allow a reset. Run through 3 rinses only -fine. wash cycle does it again.


... GE Dishwashers

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

Re:dishwasher My dishwasher was working perfect. Now, everytime the cycle is done, the detergent door is open but the detergent is sitting right there. I was using the electrosol gel pack which was working great. Now, the gel pack is sitting there when i open it. On the bottom is of the dishwasher is a lot of sand-like particles. I clean this out everytime. I haven't changed anything and am wondering why, all of a sudden, it stopped working. I've had this less than a year. Thanks.


Ginga, first of all it's still under warranty so I would call for service. Here's a few things to consider; first, I would switch back to the powdered detergent like Cascade. You want to make sure that the water entering the dishwasher is at least 12 ... Kenmore 24 in. 16182 / 16189 Built-in Dishwasher

Hi, I have a fisher and Paykel double dish drawer model DD605. A couple of days ago when we opened the top drawer all the lights flashed and beeped in sequence repeatedly and would only stop when the power was turned off or the dishdrawer closed. Today I went to turn the top dish drawer on and cannot change the cycle off rinse. I can push the eco button and the rinse cycle works no problem but I cannot change the cycle. The bottom drawer is running as I write this and appears to be fine. An


Hi\015\012\015\012\015\012Could you please let me know which all lights are blinking/lit solid in sequence from right to left. This could be an issue of drawer lock mechanism or flood switch issue. PLease post back with detai ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Frigidaire dishwasher does not start. but i see the cycle select LED light come on . all of a sudden the dishwasher stopped working. all buttons except the "start" work. i can select 'normal', 'pots n pans', select the delay etc, but the START button will simply not work!


... Frigidaire 24 in. FDBB945DC Stainless Steel Built-in Dishwasher

Ge triton I got my GE triton about 2 years ago and it has worked fine since. For some reason, now, it won't stop running through the wash cycle. I can't get it to turn off. I push the reset button hoping it will stop and all it does is go to "sensing" then back to wash. I have to open it to get it to stop temporarily, but there is water sitting at the bottom of it. Any suggetions?


Turned the breaker off and then on again.....\015\012Works like a charm!!!\015\012Thanks ... GE 24 in. GSD6660GSS Built-in Dishwasher

I have a ge profile quietpower 7 dishwasher. its built in.cannot find manuel and cannot find the serial number anywhere on the dishwasher..i need either your help with serial number or help with why water will not go into the dishwasher. motor runs water decided it wont go in. one day worked perfect and next day stopped working.


Hi\015\012\015\012This is often caused due to the fill valve. You can ... GE Dishwashers

I have a Vikin Dishwasher Model DFUD042 and the arms are not circulating water. When we start a cycle it drains previous water then fills it up after that it runs thought its regular cycle but the arms are not circulating water we have tried cleaning drain checked lines etc. still wont work.


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1741 seconds