Having problems with your Dishwashers ?

I have a Whirlpool DU1055 and when I start it the Clean Light begins to flash and it then will not start?


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Whirlpool DU1055 and when I start it the Clean Light begins to flash and it then will not start?


... Dishwashers

I have the Whirlpool Quiet Partner 1 the wash cycle starts and about 20 Min.'s into it the clean light starts flashing or the the start light, one or the other each time and it wont dry the dish's anymore we have already replaced the panel once and it has always popped when it is filling with water or changing cycles. HELP!!!! I hate washing dish's and I am beginning to hate all Whirlpool Appliances.


If the clean light blinks 7 times thats you heating circuit. Test the heater with an ohm meeting to see if it has open. If so order the heater kit and it comes with the control board. ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

Whirlpool dishwasher Clean light is flashing, we just bought it last week and after the third wash, the Clean light started flashing and it won't go off, which stops it from doing anything else. User manul says to have it serviced, but that seems unneccessary. It doesn't seem to be draining completely, so there may be a knk in the pipe, which may be related, just not sure


The blinking clean light is an interruption in the dishwasher program that either indicates a malfunction, or a simple program glitch. The following link explains how you may be able to clear the blinking clean light problem: ... Dishwashers

We have a Whirlpool ADG 7560 dishwasher which has recently started playing up. When switched on for a normal wash, after a short time the machine starts to beep. If you open the door the green programme light is on the pre rinse and the start light is flashing. After starting the cycle the few times eventually it works normally. Have cleaned all the filters etc.


... Dishwashers

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

Clean light is blinking, have already killed the power, then called to whirlpool and they walked me through resetting it by pushing buttons, however when i attempted to run it after resetting it, it started to run then went right back to the flashing clean light. i tried resetting it again, and ended up with the same result.


You may a a latching issue. d/w not latching properly. How long does it take before the clean light comes on after you reset it. does it fill with water? if so, then your motor may be defective. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

DISHWASHER STOPPING I HAVE A WHIRLPOOL ADG 7560/01 DISHWASHER. AFTER 4-5 MINUTES IT STOPS AND HAS A CONTINUOUS BEEPING AND THE START LIGHT FLASHES 4 TIMES THEN A PAUSE etc. I HAVE CLEANED THE FILTER LIFTED THE MESH AND CLEANED THE BOWL OF ANY DEBRIS AND WATER. I HAVE ISOLATED IT FROM THE ELECTRIC SOURCE LEFT IT FOR 10 MINUTES AND STARTED IT AGAIN TO FIND IT DOES THE SAME . LOST IS THE WORD THAT SPRING TO MIND. HELP!! MARTIN


... Dishwashers

Whirlpool gold, about 2 years old. the "clean" light is flashing. When I hit cancel, a 2 minute dry(?) cycle runs. The clean light resumes blinking. It will not start a new cycle


Looked in the manual and called a repairman ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

We've got an Meile Incognito dishwasher, model G 843 SCVi plus. It purges at the begining of the cycle and then seems to fill with water, but then the red Intake/Drain light starts to flash and the cycle goes no further. I've removed, checked, cleaned and replaced the triple filter and the drain pump but the light is still flashing. I spun the propeller both ways, no problem there. Any ideas for me?


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

Our Whirlpool Quiet Partner II won't run because apparantly the start button is not functioning. The CLEAN light is flashing and when we press the START button, it just flashes rapidly. Is there such a thing as getting just the starter fixed?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Whirlpool DU1055XTS Built-in Dishwasher

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash


We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

I have a whirlpool adp6600 dishwasher. the green light just keeps flashing (i think it's 7 times in a row each sequence) and the cycle won't start. have tried turning it off at the wall, clean


Dishwasher is in fault mode hold start/pause button for a few seconds this will reset the unit run your cycle again if dishwasher faults again call you local service man.good luck ... Whirlpool Dishwashers

Whirlpool Model DU1048XTPQ Will not start, clean light flashes


... Whirlpool Dishwashers

Whirlpool dishwasher clean light flashes and causes dishwasher not to start


... Whirlpool Dishwashers

Whirlpool dishwasher Will not start. the clean light keeps flashing when i push the normal and then start button it will not start.


Look behind the lower acess panel( toe kick) for the tech sheet, there is aspot cleary labeled "clean light ' blinking 7 times. ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

The clean light keeps flashing on my Whirlpool Gold GU2275XTVY0 Dishwasher, and the dishwasher cycle will not start.


... Whirlpool Gold GU2275XTV Builtin Dishwasher

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


For a drainage fault heres what the miele service manual says for your machine\015\012Water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes. ... Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

Whirlpool ADP 4501 problem. Starts normally andthen after 30 secondes or so begins to 'pulse' ie pump runs briefly then stops and the power 'start' light flashes with each pulsation. No water coming into machine, seems to be trying to pump out but stopping


Sounds like electronic module failure if there is no water in machine. ... Whirlpool Dishwashers

Can someone please help, my start light has just started flashing on my whirlpool adp 951 dishwasher has never done it before, have cleaned all the arms and filters but is still doing the same thing. please please anyone with any info would be great.


OK I SOLVED MY PROBLEM. I HAVE TAKEN IT TO THE TIP. THERE IS ABSOLUTELY NOTHING I COULD DO TO FIX THE PROBLEM. WHIRLPOOL WERE ABSOLUTELY HOPELESS, SO HAVE DECIDED NOT TO BUY ANOTHER ONE FROM THEM AGAIN. HAVE NOW BOUGHT AN LG - SO THAT WILL BE ARR ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1748 seconds