Having problems with your Dishwashers ?

Hobart LX15H Diswasher wont fill. Displays E4.


Answers :

E4 error is for

1. Low water pressure - check for clogged hose strainer; check that site water pressure meets minimum flow pressures.

2. Make sure probes are clean

3. No water pressure - main water supply valves may not be working

4. Drain valve open - turn machine OFF to drain machine, then ON. Repeat twice (this assists in clearing any drain valve obstructions). Wait for machine to reach READY mode and press WASH. Slowly open door several seconds later and note water level. Close door; 30 seconds later, open door slowly and check that water level is the same as it was. If not, repeat the OFF-ON procedure.

\015\012
\015\012I have the manual and the error details are as follows -
E1
Cause: Water supply switched off.
Remedy: Switch off appliance. Turn on water supply. Reset the cycle.

E2
Cause: Problem with electronic temperature control.
Remedy: Call service for assistance.

\015\012E3
Cause: The water heater element does not work properly or the filter mesh is blocked.
Remedy: Clean the filter mesh and if the problem continues please contact service

E4
Cause: The appliance does not discharge water.
Remedy: Check that the discharge hose is not bent, syphon is not blocked, filters are not blocked.

\015\012
\015\012please do rate the solution,thank you for using fixya.keep updated thanks.
\015\012

Sir,




It is problem Low water pressure - check for clogged\015\012hose strainer; ensure
\015\012\015\012\015\012\015\012fill high enough.
\015\012\015\012the site water pressure meets\015\012minimum flow pressures.
\015\012\015\012(Display shows E0, E2,
\015\012\015\0122. Make sure probes are clean.\015\012(See Cleaning if u have manual.)
\015\012\015\012E3 or E4.\015\012Machine will not
\015\012\015\0123. No water pressure - main water\015\012supply valves may not be
\015\012\015\012run).
\015\012\015\012working.
\015\012\015\0124. Drain valve open - turn\015\012machine OFF to drain machine, then
\015\012\015\012ON. Repeat twice (This assists in\015\012clearing any drain valve
\015\012\015\012obstructions.) Wait for machine\015\012to reach READY mode and
\015\012\015\012press WASH. Slowly open door\015\012several seconds later and note
\015\012\015\012water level. Close door; 30\015\012seconds later, open door slowly and
\015\012\015\012check that water level is the\015\012same as it was. If not, repeat the
\015\012\015\012OFF-ON procedure. If problem\015\012persists, contact your local
\015\012\015\012Hobart Service Office.
\015\012\015\0125. Delime machine




Thanks
Good Luck

Appreciate to rate as "Fixya"



Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hobart LX15H Diswasher wont fill. Displays E4.


E4 error is for 1. Low water pressure - check for clogged hose strainer; check that site water pressure meets minimum flow pressures.2. Make sure probes are clean3. No water pressure - main wate ... Dishwashers

Hobart LX30 Hey I just bought a Hobart Lx30 and we don't have a power source that can handle the 50 amp requirement. We got it at an extremely good price so we are trying to work around it. I was told that disconnecting the water heater would allow it to work in a standard 120 volt outlet. I did that and now I have another issue. The machine wont run unless the water is 160 degrees. How do i disconnect the sensor that restricts the temp so that I can run the machine at a lower temp?


Hopefully you took the suggestion to run the correct 50 amp 208-240 service to the unit.Converting the unit to an LX30C has a couple of pitfalls. The LX30C is connected directly to the incoming water supply, which should run 120-140 degre ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I am working with a Hobart C44A diswasher with a 15KW water basin heater and a Hobart bosster heater. What is the minimum water temperature I can supply to the dishwasher and maintain 160 rinse temperature required?


Hi,140F min water entering temp.http://www.instawares.com/Prod_PDF/HOB-C44A263.pdfheatman101 ... Hobart AM14-253 Free-standing Dishwasher

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

Hobart line comercial diswasher - Hobart Lx30h Commercial Dishwasher


... Hobart Lx30h Commercial Dishwasher

Diswasher wont turn back on after being moved - DW Omega 908


Have you checked the door interlock switch to make sure it is not disabling the wash cycle? ... Dishwashers

Hobart lx18 Dishwasher wont fill up


Frank,does the sump probe (the one underneath the screen) look good?It should have at least one quarter inch of metal.I have seen these break and its hard to tell but the info your describing sounds like that probe is bad or the control board.I'm a h ... Hobart Dishwashers

Diswasher wont fill


Faulty fill valve?\015\012Timeing out with insufficient flow of water?\015\012Hot water to hot and locking up valve? ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi my Lg stainless steel diswasher wont work and is displaying a e4 error message


... LG 24 in. LDF 7811 Built-in Dishwasher

Diswasher wont drain


Hi,Here is a tip that I wrote that will help you with your problem...Dishwasher ... Maytag Dishwasher

Hobart LX15H indicates E4 and will not fill.


Also looking for help troubleshooting our Hobart X18 dishwasher. ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Our hobart machine just shuts off and wont come back on again. All the lights go off.


Always put mod#, ser#, and ml# when stating problem, sounds like the switch membrane is bad. hopefully your dishmach. is an lx18,lx30 ... Dishwashers

My electrolux diswasher displays a code PF it wont reset even if i turn it off at the wall ??


... Electrolux Dishwashers

2 MONTH OLD bosch DISWASHER. WATER WILL COME OUT BUT TOP SPRAYER ARM WONT SPIN??? LEAVING DISHES ON TOP DIRTY??? LOTS OF WATER PRESSURE THATS NOT THE PROBLEM HELP!!!!!


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Dishwashers

I think I am finding small pieces of the wrap from the tablets in the small holes in the spray arms, one wont move anymore??? This is about 10 yr old maytag machine. I tried to clean out the spray arms but dont really know what I am doing. Bought a new diswasher, dont want to use the tablets if they will clog up the works. please advise.


Just prime the sink before you start the dish washer ... Maytag Jetclean II MDB8551A Dishwasher

Hobart dishwasher am14 displays 255 in temp window heater wont fire


The wash thermistor is shorted. The float and probe assembly in the wash tank should be replaced. ... Hobart AM14C-155 Dishwasher

My Bosh Diswasher model SHE44C02UC gets stuck on rinse at the end of any cycle with 1 min showing on the timer and wont clear? The water does not drain. I need Help


Module or drain pump need ed call 1-888-nyc-1055 they are pretty good with any bosch appliances. ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Diswasher wont drain


Did u put it back together properly?....that rubber stopper may have been the plug that stops water going to one of the levels....some washers have a half wash cycle that alloys only one level tobe washed for small loads ect. ... GE Nautilus 24" Built-in Dishwasher

Whirpool diswasher DU929PFGG2 wont draw water


The pump may be clogged or the motor start capacitor may be bad or the fill switch may be stuck or the timer may be bad. Fill the dishwasher by hand to just below the door level and close it then see if it will run. If it then runs correctly the pr ... Whirlpool 24 in. DU930PWP Built-in Dishwasher

I have a GE diswasher model # GSD3900L00BB, the top part of the washer tower broke off and I can't get it reattached. My dishes are not as clean. The rinse agent wont work and some of the detergent in not getting rinsed all the way out of the dispenser. Could all this be cause by the broken water tower? What do I do?


... Dishwashers

Kenmore Ultra Wash Diswasher - wont move past initial cycle


Motor trying to start. blockage in pump, or bad motor! ... Kenmore 24 in. 15932 Built-in Dishwasher

Screen says PE and the diswasher wont run - Samsung DMR77LHS Tall Tub Dishwasher


... Samsung DMR77LHS Tall Tub Dishwasher

Leak in the recyling tube on our Hobart LX18 diswasher, need to order new tube


That is called the wash pipe the part# for the pipe is 893457. that can be bought @any hobart office in your area ... Hobart 24 in. LXIC-5 Built-in Dishwasher

Bosch dishwasher The diswasher wont turn its self off it will continue to wash and will not move on to dry the dishes.


Almost certainly your element is faulty. waret does not heat up allowing timer to proceed ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0343 seconds