Having problems with your Dishwashers ?

No water entering

\015 Worked fine yesterday. Turned it on this morning and had no power. Checked the breaker and it had tripped. Flipped it back on. Unit had power but wouldn't fill with water. Thinking something electrical must have tripped the breaker of course. Checked the float which appears fine(it's down). Haven't check voltage to the valve yet. Thought I'd see what you think before I waste more time checking things that might be unrelated. If it might be the timer, can you please tell me where it's located? Underneath or in the door? No schematic came with this unit. Just typical owner's manual.have favorit 4220 no water, checked inlet valve works but still no water getting through, someone suggested float switch, how do i get that out? from inside or underneath?\015

Answers :

COLINSPARK; The timer is the connected to the back of the control dial. (the door) If nothing is working, Don't forget about the door switch, If you had a short that tripped the breaker, I bet its there somewhere. The float switch is underneath. remove the front panel under the door, the float switch is activated by that little bulb inside the machine. If you lift the bulb up and down, you should be able to hear the switch clicking. If its clicking and has power going into and out of it (when its down down) its not the float switch. I bet the schematic is on the backside of the panel underneath the door.
\015\012
\015\012RKIRK2K;.. This irregular problem does, unfortunately point to the timer/selector control. Before you commit to this expensive part. Check the door switch, it can make the same symptoms. Remove the panel on the door, find the little switch and by-pass the wires going to it by connecting them together. This this is a part that is usually $100 less than the timer. The resistance on the timer control can vary depending on what its set. But it is very refreshing having someone who can actually read one. If they have one I'm happy.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We just hooked up our old built in GE dishwasher and the water is shooting out the left side of the unit where the black water hose enters the tub. Shouldn't the water be entering into the wash arm? The hose isn't clogged. It attaches to a white plastic piece that is part of the unit itself. The water is entering both the tub but also shooting out of 2 slits approx 1 1/2" each. located right below where u attach the hose.. Any help would be greatly appreciated!


... GE GSD5130 Dishwasher

I have a Bosch SHU43C. I have a leak it seems to come out from the door. I removed the front panel. Inspected the seal and all seemed smooth and not damaged in any way. So I decided to run the machine. Waited for a few minutes and the water leaked from both corners at the same time. The water settled in the rubber trough under the door. After a few more minutes the water leaked over the trough and onto the foor. Is there to much water entering the machine? What limits the water entering


... Bosch 24 in. SHU43 Built-in Dishwasher

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

No water entering the dishwater. water supply is hooked up and water supply valve is in the open position. Could this be a water pump problem or is there a cut off valve entering the back of the washer that could be in the closed position?


No cut off on washer check float switch make sure its free check water valve make sure wires are on it and water getting to it ... Kenmore Dishwashers

No water will enter the dishwasher, There is no problem with the water supply or the supply line. The water flows from the supply line to the dishwasher connector but does not enter the dishwasher.


The water-inlet valve lets water enter the machine. Make sure it's not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if you get power to valve when unit is put into operation ... KitchenAid Dishwashers

Whirlpool dishwasher DU945PWPQ2 four year old machine - never used. Water lines are attached properly and are clear. When dishwasher is turned on the wash cycle light turns on. cycle completes but water does not enter the machine.Water does not enter the machine.


... Dishwashers

Loud humming when the water enters the dishwasher. The copper pipe vibrates. The dishwasher is approximately 11 years old. Problem slowly getting worse over time. I tried to tie down the copper pipe in the basement to no avail. When I closed the right angle stop valve and reopened, the problem got much worse and won't go away even if I grab the pipe. Only happens when water enters the dishwasher.


The fill valve solenoid has gone bad.u need to chg the fill valve assly.it is very easy to chge ad it is mounted on lhs bottom corner of the unit behind the toe panel. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.


You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

Bosch slimline dishwasher SRS560. Unit has had this fault for a while, now going a bit mouldy so keen to repair it. Displays following Symptoms 1) Firstly empty motor drains water. This appears to be fine as I can hear the gurgling of the plug. 2) Then takes water from inlet to fill internal tank. I can hear the water entering the tank, and tap pressure indicates that water is being taken in. 3) The unit then sits there and does nothing for 25 mins until programme ends. I've


... Dishwashers

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso


... Dishwashers

Water temperature difference?? Does the brada dishwasher have a heatng element to heat the water if temperature of water not hot enough. If not, then the water entering the dishwasher is the issue. Th


... Dishwashers

My dishwasher was moved for kitchen rennovations. When hooked back up again it would not fill up. It will run through a cycle but no water enters. If I squeeze the rubber hose that leads from the electronic valve to the tub it gets hot indicating that I am forcing hot water through the line. If I pour water into the tub it will wash the dishes but at the final 6 minute point it will go no further, I assume because it is not getting rinse water.


Hello,\015\012Make sure that a wire did not get bumped off of the soleniod valve. It sits usually on the bottom front left hand corner of the dishwasher.\015\012If the wires are both on the valve then the valve may need ot be replaced... ... Dishwashers

No water When the dishwasher is turned on there seems to be no water entering the tub. I checked the water supply hose and that seems to be OK. All the lights are on, evrything sounds like it's working but.....no water ?


HI thanks for your question. i would look at the water valve . located under the dishwasher. remove bottom plate . replace the water valve thanks the appliance doc ... Kenmore 24 in. 15079 Built-in Dishwasher

Hi i have a asko dishwasher the water will not enter the washer and the drain pump keeps going i have clecked the filer in the inlet do you think it could be water in the base lifting the float stopping the water inlet if so how do you drail the water out from the float? the model is d1706 thanks brian


Check this solution ... Asko 24 in. D3250 Built-in Dishwasher

I think I need to check the water pump/motor on my Bosch SHU43C dishwasher. It seems the water enters at the start of the wash cycle but then there is silence through the remainder of the cycles. Water will not spray. The drain appears to work ok to drain most of the water out. I have the washer out and upside down. Any hints on removing the base to get access to the pump? Should AI be looking at the control panel also for a fault? (the cycles seem to count down ok)


Click below;\015\012Latest Bosch Dishwasher Use and Care Manual\015\012\011\011\011\011May 4th, 2008 by Samurai Applian ... Bosch Dishwashers

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

Water not entering unit. Have checked water valve


Hi,Here is a tip that I wrote about that problem...http://www.fixya.com/support/r4021363-dishwasher_trouble_no_water_enterin ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

On a whirlpool ADP 4540 dishwasher. It starts but then the whole program starts to pulse, I can hear water being moved, but no water is entering the washing area


... Dishwashers

I DISCONNECTED WATER SUPPLY TO STOP LEAK. NOW WHEN I TURN ON THE MACHINE NO WATER ENTERS, IT JUST HUMES. THE WATER SUPPLY IS ON.


... Maytag 24 in. MDB8750A Jetclean II Built-in Dishwasher

No water my kenmore ultra wash was unused for two weeks during a renovation and once hooked back up does not allow water to enter the dishwasher. The hose has been checked and runs freely. The dishwasher runs thorugh the cycles but not with any water. Thoughts?


Two things to check. First see if anything is holding up the float inside the tub. Located on the bottom right if I remember correctly. I had a fork fall off the rack and do the exact same thing by getting lodged under the float. Second, if there ... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

ASKO 1905 - Turn the dishwasher on and no water seems to be entering the d/washer. Water is turned on. Dishwasher gets very hot as no water is coming through the pipes.


... Asko Dishwashers

Water intake alert coming on however the water is turned on. No water seems to be entering the dishwasher.


No water intake, may be a defective intake hose valve. Miele calls it, the Waterproof System hose (WPS). However, first shut off your water valve to the dishwasher; disconnect the WPS; and inspect and clean the plastic filter. If the problem persists ... Miele Premier-Plus Built-in Dishwasher

I have an Indesit IDL 42 dishwasher. It has entered a state in which it behaves like this: as soon as I turn it on, it starts swishing the water around (it doesn't pump it out) and it does that regardless of whether I press any buttons (I have tried Start, Reset, turning the program knob, no difference at all). When I open it in the middle of this cycle, the water drips, and there is plenty of water (about 1 in) at the bottom. I have checked the filter, it is clean. Can you please help?


... Dishwashers

Only a small amount of water enters machine when you start normal cycle. I took off water supply line at inlet valve... screen is clean, water preasure is fine.


You might have a bad water inlet valve, when triggered the inlet valve opens up to allow water to enter the machine, it's usually located behind the lower kick plate in either the right or left hand corner, if it's defective it would need to be repla ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1009 seconds