Having problems with your Dishwashers ?

I have a Bosch dishwasher and the upper arm that spins and dispenses water has come off. There is a bracket on the back wall with 2 protruding pieces and an open whole in the middle which seems like the water comes out of it. There are 2 metal "clips" on the side of this braket which seems like the plate part of the spining arm should be able to attach to it.. I cannot figure out how..Any helo would be apprecated..


Answers :

On Bosh dishwasher you just slide the upper arm vertically until it snaps in place. The arm attachment will snap automatically into the clips, onto upper dishrack, unless the upper arm is damaged

fed0db6.jpg

If the arm does not snap in place, then the attachment to rack is damaged, in that case replace the arm. A workaround solution is also fixing the spray arm to the rack with two plastic O rings (I have done that , and it works, just tie them firmly to the rack).

You can get parts entering model number here.

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch dishwasher and the upper arm that spins and dispenses water has come off. There is a bracket on the back wall with 2 protruding pieces and an open whole in the middle which seems like the water comes out of it. There are 2 metal "clips" on the side of this braket which seems like the plate part of the spining arm should be able to attach to it.. I cannot figure out how..Any helo would be apprecated..


On Bosh dishwasher you just slide the upper arm vertically until it snaps in place. The arm attachment will snap automatically into the clips, onto upper dishrack, unless the upper arm is damaged ... Dishwashers

Maytag diswasher MDB6600AWW Sprayer arms don't spin. Dishwasher makes all the right noises, except for spraying. Water fills properly and heats up. Water drains properly. Found paper on the back of access panel. Ran Manual Function and Field Service tests, no problems indicated. Disassembled all the pieces inside the bottom of the dishwasher. No obviously damaged parts. Shaft for motor turns freely. It seems like the parts that attach from the impeller to the motor shaft don't


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

The dishwasher doesn't seem to have nearly enough water in it. The upper sprayer arm doesn't seem to be spinning when running (I open the door and look really quick) and the lower one looks like it barely spins and barely sprays water. The dishes are barely wet and the soap is just laying on the bottom. The water is on, there are no kinks in the supply line. It sounds like it is running, and pumps pumping, but being brand new I am not sure what it should sound like. It certainly doesn't sound li


I would lift the drain pipe higher. approx. 1/2 the height of the dishwasher . also rechack incomming water supply. Make sure no blockages and the like. Try again. ... Bosch Dishwashers

I have a McCULLOCH 1500 psi pressure washer and it seems like I need the top part of therod where the waer comes out it no longer adjusts the water stream seems like a little plastic defkector that you adjust your stream with, snapped and broke looks like I HAVE TO REPLACE THE ENTIRE TOP PART OF THE 2 PIECE ROD on the bar it says the following max130barmax60C PA66-GF30 Where could I purchase this piece Andy Nowostawsky my adress is 15447-rue d'esterel Pierrefonds,Quebec H9H 1Y9


... McCulloch Pressure Washers

Hello, Im trying to diagnose poor cleaning of glasses in the top rack of my Fridigaire FDB751SCB0. everything seems to work fine but while testing I noticed the upper arm isn't spinning. the lower arm is. i believe the pump is working as water is spayed everywhere inside but no matter which position I leave the upper arm in, I find it in the same place when I open the door. what could cause the upper arm to not get water preventing it from spining?


Hello; first thing to check, which you don't mention, is which side of the glasses aren't coming clean; the outside, which would be caused by the TOP spray not working properly, or the INSIDE, which would be caused by the spray BELOW the top rack not ... Dishwashers

Hi, I have an LG LDS4821 dishwasher and it appears to stop working properly. The dishes don't seem to be cleaned at all. It seems like the spray arms are not spraying the dishes as the dishes are still dry/dirty after a normal wash cycle. I did notice that the detergent was used during the wash, and a trail of white residue was at the bottom of the tub. I can hear water pumping into the dishwasher, but when I opened it during a wash cycle, there was a puddle of water at the bottom of the


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDS4821 24 in. Built-in Dishwasher

Upper & bottom arms are not turning even though the motor seems OK, pump for draining seems OK too. rcently I changed the pump kit plus some gasket and seals. My Maytag is about 14 yold and was very good for me untill I changed the parts. Could it be a weak motor pump. The water splashes very much in the machine but no arm turning!? Help me thank you Ben


Hi Ben, had the motor impellor shattered in the old pump ie-chunks broken off ? if so there is every possibility that these pieces have lodged in the wash delivery pipework at an elbow or indeed at the arm boss itself -i would try to check as much of ... Dishwashers

I have a Maytag DWU8250BAX and the thing leaks like crazy. I just replaced the door gasket, but that is not the problem. When I took a closer look at the door it seems as though the water is getting up and into the door through a space in the bottom of the door. It seems to me like there should be another door seal to fill a gap that sits between the door hinges. If anyone knows if there should be a seal here and then what the part number might be that would be great. Thanks!


There is an airgap under the door..it should spray up and run down the door not spray up under it..look for crack or hole in spray arm..if there is the wrong soap in it it will flood out with lots of bubbles..just have to flush it out. lastly, if you ... Dishwashers

Whirlpool dishwasher doesn't seem to fill with enough water despite good water pressure. Therefore, pump sounds like it is cycling from pumping water for about 2 seconds to going dry for 2 seconds to pumping water for 2 seconds to going dry for 2 seconds, etc. Spray arms rotate only for the 2 seconds when pump is actually pumping water. Dishes do not get clean.


... Whirlpool 24 in. GU2548XTPS Built-in Dishwasher

We recently bought a house with a Kenmore 363.16222100 (?) dishwasher. No manual. Monday night it didn't drain properly and leaked some water on the kitchen floor. The cycle had finished when we saw the water on the floor. We bailed out the excess water. I took off the drain cover and insert. I couldn't see an obvious clog problem, but cleaned it out. Then I tried a short cycle, interrupting it to shorten it. No problem. Water seemed to drain fine. I did find a part that looked like a straw and


HelloWelcome to FixyaMy name is Huum,You can find your model dishwashers manual here at this site. this sitehttp://www.managemyhome.com/mmh/lis_pdf/OWNM/L0801624.pdfI feel you should not invest blindly in someone ... Dishwashers

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

Holding water There is water in the bottom of the machine after the cycle is done. There is definitely draining going on throughout the cycle, but it's not draining completely at the end -and the water that is left is murky. Spoke to a friend who tells me it sounds like the dump valve, but in checking on line, that doesn't seem to be a part that even exists any more. Do I need to buy a new dishwasher? This was not in the budget this year... Thanks for any advice! Nancy


Are the dishes getting clean at the end of the cycle, if not then there could be foreign debris in the pump housing that can cause this, needs to be dismantled and cleaned out, if dishes are clean then the pump impeller will need to be replaced ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Kitchenaid KUDS01IJ lower spray arm wobbles and hits the water feed tube. The parts seem ok. Is there something that is supposed to push the lower washer arm support up?


... Dishwashers

My dishwasher starting but it seems like the ARM spray isn't spinning there's barely any water coming out of the spray ARM


... Frigidaire Dishwashers

My Kenmore Elite model # 630.16302402 dishwasher isn't getting the dishes clean. A lot of food is still on the dishes after cleaning, especially inside the glasses. There is a white film on glasses and the inside of the appliance. I also just noticed that the upper arm isn't turning. There is about 1/2 cup of water standing in the drain area (not visible until removing the filter tray at the bottom of the appliance). Is this normal? The obvious problem is the upper arm but it seems like the rin


Hello, \015\012 \015\012 ... Dishwashers

Grinding The situation: I have had my Whirlpool DU915PWPB1 for 2 1/2 years, it isn't the greatest dishwasher but does the job good enough. Recently, the water will fill, the washing cycle will run but then when that part stops it goes into a whirring that seems like a motor is going but nothing is moving. I have removed the Filter Modual in an attempt to find out what the grinding would be. There doesn't seem to have anything in the way or under the filter. I have ascertained that the grin


Noise probably not from there when reassembled the plate will not be direct contact with screen noise is probably from wash motor itself..suggest checking owners manual for warranty info ... Dishwashers

It always seems like it never gets enough water to even make the spray arms work. I have even tried to make sure I am not running any hot water in the house. It is about 7 months old and has always acted this way. Could there be something wrong with the installation? My old Sears never had this problem.


Sounds to me as if there is a blockage in the water line supplying the dishwasher or a kink in the water line supplying the unit. Since the water is supplied from the angle stop under the sink there could be blockage at that point. What I would sug ... Dishwashers

Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers

I had a service tech at my house to repair my refrigerator. He also took a look at my Maytag WU504 dishwaser, which was not cleaning the dishes anymore. He was less familiar with dishwasher diagnosis, but found that the lower spray arm was pumping out water through the jets properly in the cycles, but that the spray arm was not rotating. He seemed stumped and called his supervisor, who suggested it might be the wash impeller. I have looked at the parts diagram on partselectdotcom and taken t


You are absolutely correct!!\015\012\015\012The support retaining nut allows the arm to spin without falling off.\015\012\015\012And it would definately cause dishes not to clean if the arm didnt rotate.\015\012\01 ... Dishwashers

Miele Dishwasher Model G1040, Type HG03, NR: 32/65143704 The machine is three years old. The cycle reaches almost to the end, then all three LEDs merge together, and the pump runs continuously, even with the master switch off. I have taken the machine out and removed the base plate. When I first took the machine out of its position, I tipped it backwards and water came out of the bottom. All hoses and parts in the bottom section seem perfect in every way but the inside of the bottom plate indica


... Dishwashers

Bosch shx33a05uc/14 dishes are milky with white chalky residue. Have cleaned the inside, and checked to make sure the water can exit the spray holes in the circulating parts (top and bottom). Checked that hoses are not kinked too. Seems like it's rinsing with dirty water.


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Bosch 24 in. SHX33A05 Stainless Steel Built-in Dishwasher

Figidare dishwasher Upper arm not rotating, no water coming from top hole to fill upper arm.Lower arm rotates shoot water up cleaned filter screens. Check ball seems ok by pump, is there a location it (ck ball) should be? My upper arm is not rotating, things are coming out crusty, and it's definitely not getting water to the upper arm. My check ball seems to be plugging the tube the water goes up in.


It seems other posts were correct - The upper arm doesn't spin all the time. Once I learned that, and let the dishwasher cycle through, I saw that the upper arm does spin. So, there wasn't a problem with the upper arm afterall. That doesn't solve ... Dishwashers

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

HOD6615 Vision one dishwasher - water is not heated, errors after 15-20 mins. Element seems to meter out ok, is this more likely to be the safety switch or control panel, any tests to prove. Could anyone tell me what part the safety switch plays in element connection.


... Hoover Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1699 seconds