Having problems with your Dishwashers ?

Frigidaire dishwasher Model# FDBB4365FC0 Display shows PF (blinking) Air Dry and High Temp Wash LEDs are blinking Electronic board has recently been exchanged.


Answers :

Hi t_l_stock...hope this helps..Good luck..

Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.
Some models have options that may require a water heating delay, such as Hi-Temp Wash, Hi-Temp Rinse, or Sanitize. Additional time may be required to heat the water to the proper temperature. The dishwasher will continue to circulate water during this heating delay but the timer will not advance until the proper temperature is reached.

To help fix this: 1) check the temp on your hot water heater, set for at least 120 deg. 2) select the heated rinse option if you have one

http://www.frigidaire.com/customersupport.aspx

here's a link where you can download manual for your dishwasher..in case you might need..

http://www.retrevo.com/search/v2/jsp/mytrevo/myTrevo.jsp?page=man
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Frigidaire dishwasher Model# FDBB4365FC0 Display shows PF (blinking) Air Dry and High Temp Wash LEDs are blinking Electronic board has recently been exchanged.


Hi t_l_stock...hope this helps..Good luck..Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may require a water heating delay, such as Hi-Temp Wash, Hi-Temp Rinse, or Sanitize. Additional time may be re ... Dishwashers

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

Recently replaced the control board for Electrolux EIDW6105GW1; after nearly a month of working w/o any problems this evening the machine made it through the wash cycle and then stopped working (all lights on wash cycle door menu are flashing). Took kick plate off bottom to check control board and the leak dectector is lit. I can see no leaks in front and am reluctant to do anything else with this POS. I spent nearly $1000 on this 18 months ago and have already sunk over $300 into a new contr


... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Hey guys, I am a dishwasher repair guy in barbados, the caribbean. I am having problems with a Hobart LX30H. the relay board is doing half the things right and the othrs not at all. I replaced it with a new one and the same results. At startup, the wash sump heater and wash motor are running, but the fill valve, drain valve and rinse booster are not running. Hence the startup operation is stalled. the funny thing is that the rinse booster and fill valve led's on the relay board light up at


Not sure what sort of problems (fault codes etc) you were having before you chose to go on the path of replacing the relay board.\015\012\015\012It might help to know what fault codes you have been noticing.\015\012\015\012One ... Dishwashers

Electronic control pad is pushed for quick wash and the LED display would show 52 minutes. Now when it pushed the display shows 17 minutes and performs all the functions that would occur at the end of a normal cycle. Can set for the longer wash cycle 94 minutes and performs all functions start to finish. Think the control board is bad any advise.


... Maytag 24 in. DWU9902 Built-in Dishwasher

Whirlpool dishwasher This dishwasher quit in the middle of a wash cycle,we had to empty it and wash by hand. I thought that maybe the breaker to the dishwasher popped but when checked it had not .I then noticed that there are no lights on the electronic key board .Even when not in use there should be one red LED that is lit. It almost seems as if there is no power to the dishwasher. Is there some type of backup safety switch or breaker on the dishwasher itself that I could reset?


Fuse on control board. ... Dishwashers

I have a Bosch SHE44C05UC/43 dishwasher about 2.5 years old. It just started recently to stay in the wash cycle forever. The number on the LED panel decreases in the normal fashion, but the dishwasher never changes from the wash cycle to the drain and then rinse. I have verified the incoming water temperature is adequate


You must change the module. that will solve your problem. let me know how you made out.:) ... Bosch 24 in. SHU5305UC Built-in Dishwasher

I have a whirlpool quiet partner i dishwasher (model DU1055XTSQ2) that has suddenly stopped working. Control panel has partial functionality. All of the buttons on the control panel have a green LED feedback light when depressed. None of them provide LED feedback anymore except the Hi-Temp Wash, Sani-Rinse, and Heated Dry buttons. So there is power to the dishwasher. Any ideas? Please help Scott


The control board has failed.CLICK HERE to see the parts breakdown. ... Whirlpool DU1055XTSQ Built-in Dishwasher

Hobart lx18 no power to detergent pump, during the wash cycle there is no power present at the connections for the pump, during the rinse cycle the sanitizer terminal will pulse power and the rinse aid and sanitizer pumps will run, is the relay board bad? With the top drawer open and running the led for detergent never lights up during the wash cycle.


You have to go into program and activate the detergent pump.sounds like somebody deativated the det. program ... Hobart 24 in. LXIC-5 Built-in Dishwasher

The dishwashwer didn'tallow me to select the various wash cycles. Only light wash worked. I replaced the main circuit board and now only the high temp wash/semi rinse/ heated dry option work.


... Electrolux Kenmore 24 in. Built-In Dishwasher with 5-level Precision Direct Water Delivery System Dishwasher

Temperature display on the booster led periodically reads the temperature as zero, even though the water temp is at 180. I visually checked the circuit board and it looks ok. Thermistor or board or both bad?


... Hobart AM14C-155 Dishwasher

Dishwasher is 16 months old. Recently, it won't get tea stains from spoons or cups and there is a white film on plastics. I have run unit once with vinegar. I tried using less detergent and no change (Cascade Complete). (Neighbors using same detergnet on different machine with no problems so it's not the water.) I always select High water temp and air dry on normanl wash. My hunch is that the motor is going bad and therefore it is not pushing the water with enough force.


Hello, there are a few thinks to check on the dishwasher. Circulation, drainage - no backflow back into tub, and water temp. If all three are good, then you have hard water. \015\0121. circulation - These MDB models are very good with water circul ... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers

I purchased my Kenmore Elite dishwasher, model # 8542514, in 2003 & replaced the control board in 2006. Recently, I accidently opened the dishwasher during a wash cycle, but it continued working once I closed it. It seemed to work fine for a few more weeks. Now, however, I get nothing--no lights....just doesn't start up. I tried pressing all the code solutions listed on this site, but no luck so far. It seems to me that the control board/panel should last more than 3-4 years.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Asko 1875 had a new main board, wax motor and temp thermistor fitted 6 months ago. now thw machine pumps in the water but does not wash what could be the problem


Hello, welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko 1875 and 2) filling with water, draining, heat ... Asko D1876 Dishwasher

Kenmore dishwasher 665 17023401. Recently it had green light blinking, would not start. Read elsewhere on line to alternate pushing hi temp wash and heated dry 5 times to get it to go through diagnostic. Now upper spray arm seems to have water coming out but does not spin.


... Dishwashers

Dishwasher bubbles I have a kenmore elite mod- 16599201 stock # 16599 , recently there has been bubbles in the washer after the wash cycle ends . I thought that I might of put detergent in the jet dry hole so I removed the dispenser and rinsed the whole thing completely clean and reinstalled it. but the bubbles are still there . I think its the jet dry not completely rinsing away. I cleaned the dishwasher with vinegar and then glisten. My water temp is slightly low as I have my water heater set


... Dishwashers

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

The unit is a Maytag model MDB5601AWW which it has recently began to lose power at the touch pad. The electrical breaker has been checked to confirm normal voltage. Additional investigation suggests that the unit can be reset by (1) disconnecting the power at the breaker, (2) disconnecting and reconnecting the ribbon cable that interfaces the touchpad with the control board. However, the problem reoccurs after a few normal wash cycles.


It sounds to me then that the display board or touchpad needs replacing,you havn't said that it's not doing it's cycles.so it's not causing any washing or cycle problems.i would replace the display board. ... Dishwashers

I have a Bosch dishwasher model SHE4AP02UC/06, serial number FD901102579 that has been used twice since installation. When I select the Regular Wash cycle, the Regular Wash LED and the Active LED come on. The machine washes the dishes and then when it stops making noise. At that point the Active LED goes off and the Clean LED comes on with the Regular Wash LED. These LED's do not go off. There is no signal saying that the dishwasher is finished. Is this the way it is supposed to be operating or


Ya id say until u open the door after it has washed ... Bosch Dishwashers

I have a Kenmore ultra wash quiet guard 3 dishwasher with a Hi Temp Wash that won't stop flashing. I've tried shutting off the circuit breaker and every code button sequence I can find including pressing Hi temp wash, heated dry, hi temp wash, heated dry...but it won't stop blinking..always blinking...Anyone have any other suggestions to reset this?


... Kenmore 24 in. 17019 Built-in Dishwasher

MAYTAG MDB7600AWQ DIAGNOSTIC CHECK USING CONTROL BOARD AUTO AND MANUAL, ARE GIVING ME A HIGH CURRENT WASH MOTOR DIAGNOSIS.(NORMAL WASH FLASHING) THE BOARD ITSELF CHECKS OUT OK. ALL FUNCTIONS WORK AS THEY SHOULD.WASHER FILLS THEN ATTEMPTS TO RUN FOR (ABOUT 3 SECONDS) IT WILL DO THIS 3 TIMES THEN BOARD GOES BLANK. ALSO, THE WASHER WILL FILL WITH THE DOOR OPEN??? BUT WON'T ATTEMPT TO WASH. REPLACE WASH MOTOR?? THANKS lYNN


I would agree.. Here is a site for you to copy and paste in your address bar that I think will be helpful:http://home.howstuffworks.com/how-to-repair-a-washing-machine.htm/printable ... Maytag Dishwashers

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

The machine fills ,drains and washes as normal. However when it fills the wash temp is 60 as normal but the rinse temp wont go higher than 76 deg C . when the wash cycle is on , the cycle stays on wash not progressing thru drain and rinse What is the cause?


Hello. Let me assist you. There are only two reasons for your problem - if you can isolate your problem based upon these descriptors you will know which part to replace:\015\012\015\012\015\012\015\012\015\012\015\012\015\012Water-he ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1191 seconds