Having problems with your Dishwashers ?

I have a Beko DWD5410W dishwasher. It has been working well for a couple of years now. Last week is stopped during a wash cycle and now when you switch it on, it fills with water to the top of the filters (as normal?) and stops. Nothing further happens no matter how long I wait unless I switch the machine to drain mode. Do you have any idea what the problem could be or how I can go about investigating further? Many thanks in anticipation


Answers :

Hi, this is a control fault that is localized in the logic sector of the control board. the logic chip which holds all wash programing is damaged. you will need to replace the control asap if possible...

thank u rate me

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Beko DWD5410W dishwasher. It has been working well for a couple of years now. Last week is stopped during a wash cycle and now when you switch it on, it fills with water to the top of the filters (as normal?) and stops. Nothing further happens no matter how long I wait unless I switch the machine to drain mode. Do you have any idea what the problem could be or how I can go about investigating further? Many thanks in anticipation


Hi, this is a control fault that is localized in the logic sector of the control board. the logic chip which holds all wash programing is damaged. you will need to replace the control asap if possible...thank u rate me ... Dishwashers

I have a very old domestic Hobart dishwasher. The micro switch that is controlled by the float on the inside left of the machine has malfunctioned . I believe that this micro switch controls the "water in" valve/solenoid. It's ID = UNIMAX 2TMT2002 4 Y , 10 amp-1/4hp 125-250VAC. It's an odd switch as it's lever is about 25mm long and has a paddle on the end to line up with the plunger comming through from the float inside the machine. It also only has 2 prongs for connection and 2 holes fo


... Hobart Dishwashers

We have a Whirlpool GU980 Series Dishwasher. All the lights work. No matter what setting I use, it fills up, and then nothing happens. The "washing" light will be turned on, but nothing happens. I try to drain the machine, it will make a sound like it's going to begin a process, then it just stops. Do these things just "die" after some time? This machine is 7 years old.


Sounds like something is caught in the pump impeller. you will need to take the pump apart inside the tub. ... Whirlpool GU2400XTP Built-in Dishwasher

After dishwasher was started, and water stared to enter the machine, it was unlatched and left with the lever in the open position for some time. The control dial had automatically moved 5/6 degrees clockwise and left there. Now the machine does not want to start no matter what I do. Power is to the machine, latch is moved to the right, but nothing happens. What's next. Thanks for any help you can give.


Hi,\015\012 \015\012After the water stops coming in do you hear a humming noise? If so the motor may be stuck. Unlock the door to disconnect power from motor then turn the motor by hand a few times (should ... Dishwashers

I have a Braun combimax 650--it is fairly new. It was working fine last time I used it, but this time, the dial that turns the machine on seems to be stuck. The little button for the pulse does work. I read the instructions, which said that this might happen when the machine overheats and to wait fifteen minutes, but it is definitely not an overheating problem and the last time I used it was weeks ago.I love this machine and now need to use it for quite a number of things--any help you can provi


... Braun K-650 CombiMax Foofs Processor FOR 110 VOLTS

Dishwasher confused Dishwasher was switched off just after cycle commenced (tablet had been released). On restarting dishwasher, it wouldn't take in water and has just been going through the motions of the cycle without anything happening. Even when the power button on the machine is switched off or the door is opened, the motor continues to run but without water. Water is definitely switched on under sink. I think the computer is confused - can you please help?


I suspect this is nothing to do with switching off during the cycle.take the bottom plate off and check if there is water leaked into the bottom pan. alternatively, if you can, tilt the machine back to 45deg and see if water runs out.most ... Dishwashers

Hi I have a LG dishwasher, model LD-2052WH/LD-2052SH/LD-2052MH. The machine is about 30 months old, and used very seldom. In the last two weeks we noticed a very loud "grinding" sound emmiting from the machine. This sound usually happens when you switch the machine on as the water if filling or the wash blades are rotating. What is the cause of this, and how can I get it fixed? Regards Paul Naidoo Ph: 0027 83 651 7558


... LG Dishwashers

The dishwasher is cutting out the mains rcd switch when running? This happened during an intensive wash now as soon as you switch the on switch it trips the cut out! I have checked the both pumps for earth or neutral leaks and also the the heater but all seem fine. I only have a multi meter at my disposal so therefore cannot do a proper earth leak check. the machine is approx four years old and is not used very often.


Hello, dawhI\012 was trying to help you out here. I am not sure if this well help you? \012But here is a link to about everything you want to know about your \012dishwasher, from repair to trouble shooting on most common dishw ... Zanussi 32 in. DE6755 Dishwasher

I purchased a diswasher (Hotpoint)about 1-1.5 years ago. It's model # is HDA3400G02CC and its SS# is TH887451Y. I don't think I registered it. No Matter, Two days ago, my garbage disposal stopped working. I checked the outlet. It had power. The switch to the Disposal was next to the outlet. I assumed that the switch was wired from the outlet. It wasn't. Bottom line, the switch nut was loose. I tightened it and problem solved. When I turned on the dishwasher, nothing happened. It acts like


I purchased your service (telephone support) and the dishwasher expert contacted me. We discussed the issue, he made recommendations. I followed his advise and solved the problem. Before I could recontact him, he called to follow up on my progress. ... GE Dishwashers

I have a Whirlpool ADP4530 and recently the light above the start button flashes 4 times, pauses and repeats this. The machine won't start unless switched off and then after a while when switched on it will run a program. Any help appreciated.


... Whirlpool 18 in. ADP530 Free-standing Dishwasher

Hotpoint ADP 4501/5. Machine switches on (ie the lights come on) but nothing happens when you try to run any program and there is a pool of water at the bottom of the inside of the machine which hasn't drained away.


This may be due to some block in drain outlet. please check the outlet pipe ... Dishwashers

There is a pool of water on the floor of the machine (inside). I have taken out the metal filter and the cone but nothing happens. I only realise this when I went to swithc it on and absolutely nothing happened when I closed the door. The lights go on, but there is no attempt to switch on!


... Neff 18 in. S5943 Slim-Line Built-in Dishwasher

It does not matter which cycle is chosen, once "start" is pushed on our Asko D3120W the drain pump comes on empties the machine, then it fills for the first time, and turns off. It happens on all cycles. We have turned off the power thinking that would re-set the machine, but it has not worked. Do we need service or is there something we can do at home?


Hello &\015\012Welcome to FixYa\015\012\015\012The problem\015\012seems to be with the frozen main pump or the pump seal/impeller gone bad. To\015\012solve this the pump and motor has to be removed and then the part rep ... Asko 24 in. D3120 Dishwasher

F2 and all panel lights flashing part way through cycle. Machine will not switch off unless you switch power button off


Hi \015\012You have water in the bottom pan.Turn off power Remove bothe front and rear lower panels and dry out pan with a towel after tipping water from pan. Turn on power and try operating the washer and look for water leak. It could be com ... Asko D1876 Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

I have a slimline dishwasher from Ikea. The model is Whirlpool DWH C10 W manual. Everything worked fine up until the other day when I switched the machine on and it made a noise as if it was working but nothing happens. No water comes into the washer although inlet pip looks fine. I have poured water in and it is drained okay but the dishwasher is not cleaning dishes. After checking through numerous forum and reading about a flood prevention switch which can be sorted by tipping the d


Ok so slow down and lets look at the d/w problem and don't take the kitchen apart.. in the tank there is a float in the front corner. lift the float and listen for the click that would be the float sw . if no click th ... Dishwashers

My dish wash machine (HOBART FX/CV series) is programmed to PO1 and it should be running for short cycle but what's happening is it keeps on running for a long time...please help..many thanks..


... Hobart 24 in. LXIH-3 Built-in Dishwasher

Ge dishwasher model gld5560l00ss --when you hit start nothing happens - if you hit start again , light on any selected switch begins to blink. have tried rebooting control that was suggested in owners manual by tripping breaker and then resetting after 30 seconds, ( this did not change anything). machine makes no noise but lights do come on.


... GE Dishwashers

Normal wash cycle- tub fills (?), then comes a loud hummmm and nothing happens. I noticed water level didn't reach heater coil and added water until limiter switch clicked. Still just a loud hummmm. Machine was well into its regular cycle when this first occurred, but now, won't even get past initial fill. Pushing the "Cancel/drain" button activates motor and pump: they work fine.


You are an expert enough reading this. But with a terrible complicated dishwasher. First clear the waterlevel problem.\015\012Rest is a result. You do not need me, join us. Next time buy something more plain. ... Dishwashers

Hi, I have the Bosch Logixx Dishwasher . BOSCH SGS0922gb /06 .. aged about 6 years old .... When I press the on/off button 'on' the led display only shows the 'not started' message. When I press the on/off button 'off' the led display lights up momentarily with 'start' etc just before I have fully released the button. I have tried a new switch and the same happens so not that. ALSO i can sometimes see S1....> on the top panel and get the machine to show on the top panel the close door


... Dishwashers

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

The green light indicator on my Bauknech dishwasher is blinking and the machine does not work. What can i do? Itried to switch off and restart but it does not stop blinking and nothing happens. Please, help!


Trip the breaker again. While power is off, dry all the water, if any from the bottom of the tub. Remove drain well from inside the tub and clean it.Access the back of the appliance and check inlet and drain hose for restriction or blocka ... Bauknecht Dishwashers

Balay slimline dishwasher. When switched on and programme selected, appears to start with water entering the base on the machine but then nothing else happens. Able to empty water out by resetting and chosing rinse programme.


... Dishwashers

My beko DWD8650 dishwasher has stopped working - when I switch on the power, the machine sounds as though it is trying to work, even though the start button has not been pressed. Once the start button is pressed, the timer does not count down and nothing else happens.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1083 seconds