Having problems with your Dishwashers ?

Dishwaher to have a dishwaher installed do you just use your existing pipes that your washer uses


Answers :

Generally, you need only hot water. It is advisable that the drain line be a little lower than used by a washer. Drains usually go into a modified portion of the sink's j bend in the drain. This sits at about 18 inches off the floor. You should fuse your electric line for 20 amps at 120 volts or 15 amps at 240, depending on your location. North American units are at 120.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwaher to have a dishwaher installed do you just use your existing pipes that your washer uses


Generally, you need only hot water. It is advisable that the drain line be a little lower than used by a washer. Drains usually go into a modified portion of the sink's j bend in the drain. This sits at about 18 inches off the floor. You should f ... Dishwashers

We just purchased a used Fisher and Paykel DS 603-i. After installing and running the normal cycle there was a lot of water left on the bottom of each drawer. We ran the bottom drawer (water stil siiting on the bottom of the top drawer) and part way through the main wash cycle we got what I think was a F1 error code (we do not have the LCD version but the Rinse light was activated). I took out the bottom drawer, dried out the basin and then took out the washer and reattached the drainage pipes t


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

The waste pipe on my hotpoint dishwasher is connected to a spigot. I now want to buy a Bosch replacement but all models have a waste pipe which is too small in diameter to fit the existing spigot. A smaller spigot does not seem to exist and there is no room to install a stand pipe. Can you suggest a solution? Thanks


Do you have a garbage disposal? It is usually easier to drain through the garbage disposal. There is a fitting for this on all disposals. Be sure to remove the knock out plug first. ... Dishwashers

Leaking input to the top of the dishwasher. Pollypro pipe comes up the back and into the top centre of the machine.... This is squirting out water when on wash cycle. Have undone large plastic nut on iside.. that has rubber washer on it... but the input pipe does not seem to have a washer between this and the steel body of the machine... this seems to be causing the water to squirt out... please let me know whether the washer has disintergrated or whether I need to use some bedding compound t


\015\012By reading Your problem most probably due to disintegration of washer only. Try with new Washer \015\012\015\0121. First try to adhere some wax or gumming material where washer is distingrated...if it solves u r probl ... Dishwashers

I have just bought a Kenwood KID60S10 dishwasher. I have used it a couple of times with no problem. However I realised it has been leaking from the water pipe at the back so pulled the unit out to tighten and readjust the pipe. However when I tried to run a cycle it won't after this to check if it was still leaking it won't. When I choose a programme non of the lights light up (except the power on/off light). I had left the washer out of the cavity to ensure the pipe wasn't leaking anymore. It i


... Dishwashers

Kodiak 4000 Bear, Washer runs smoothly, press trigger and washer begins pulsating jets of water, good pressure, used air hose on washer water line and wand, problem still exists. wash application


... Pressure Washers

I have a pressure washer with a faip 3 piston pump. the other day i was using it and it stopped unloading. i cleaned the unloader and it didn't help. I bought a new one and it still won't work. I e-mailed Ryobi and they will not respond. There were no instructions on installing and adjusting the unloader. Could you give me an idea how to install and set up the new unloader. Any help would be most appreciated.


I think your main problem is that the unloader valve needs to be lubricated. Use the very best water resistant bearing grease you can find. If you can e-mail me a pic of your unloader assembly I can try to explain how to set it up. [email protected] ... Honda Pressure Washers

Our Whirlpool dishwasher is two years old and using the same dishwasher and glass cleaning fluid since we installed the unit we are now getting soapy suds in the washer when we open the door. The installer told us to put cooking fluid in several times and run the machine on "rinse". We did this several time and we are still getting suds. Frank Hill 508-879-7425


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... Whirlpool Dishwashers

I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting


All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine.  ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Our GE Profile (Quiet Power 6) dishwasher is having trouble cleaning our dishes. The top shelf rarely gets cleaned and the bottom is questionable. It used to work fine. We always use Cascade powder detergent on a normal wash cycle. We have hard water. Any advice would be appreciated. I took apart the washer looking for an obstruction but none existed.


The obstruction can be external to the unit. Check the drain at EACH connection working backward from the sink connection all the way to the motor pump outlet hole. Do not forget to dis-assemble the Air-Gap (if installed) and to check the inside of ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Dishwasher - The dishes and glasses do not come out clean. There is approx 2 inches of soapy/dirty water that remains at the bottom of the dishwasher. I was told by the sales people that this was normal in order to keep the ... moist. I have since leared that this is not normal. The washer was purchased approx 1 1/2 years ago and was installed last January. Problem has always existed. I have replaced the Drain Pump because when I spoke to someone at GE that was thought to be the problem. NO


Your problem is to removed the clogged into the drain.. I'll post back again and post here the steps to removed the clog..Thanks ... Dishwashers

Installing model 665 kenmore dishwasher with granit counter top.The side bracket we are trying to use need to be snap of at the line to get dishwasher to fit right.The problem is we cant get to the screw the side of the washer is in the way and no hole is in the side of the washer.Need a real fix.


... Dishwashers

I have an EXCELL EXHA2525 pressure washer that I bought used - the front of the pump assembly consists of what looks like (2) pipes and it basically holds the assembly together, along with the fitting


... Karcher 2500 PSI Pressure Washer

2 years old but NEVER used it yet. Put on today and it would not run any cycles. Let in water and emptied it out but would not do a wash cycle. All this from start to finish in about 8 mins. Washer kept making this droning noise as if it was trying to do something but couldn't. Checked all the waste pipes and filters - all clean - By the way it was still empty of crockery when I tried to do this. Bosch Model SHV55 MO3GB


Dishwasher have a antiflood device system in the base of the applince try a tip the machine backwoord or sideway if water comes out the base you have a leak generally associate wit a failure of the seal around the impeller of the motor or the microsw ... Bosch Dishwashers

I have a electrolux EIDW6105 dishwasher,since new,after a load of dishes are done,by the end of the day,the inside of the dishwasher smells so bad,like rotting food,it is almost unbearable to smell.I had a service tech come and check it out,he said the washer was not installed correctly,was not level,I made the change,same problem,then he said I would need to use DISHWASHER MAGIC once a week,same resault,then he called electrolux tech support and they told him that it was nomal and I should run


... Electrolux 23 in. ESI602X Built-in Dishwasher

My Honda VR 2522 on Excell 2500 psi pressure washer run good when in use but when i release the trigger on the wand the motor idles and begans to pulsate, hit and low. Where to i start looking to repair. I have a new air filer installed Roy


... Karcher 2500 PSI Pressure Washer

The whirlpool dishwasher I just bought used and installed in my rental property leaked from the bottom of the front door. The dish washer had been sitting for some time before I bought it. What will fix the leak?


Buy a new door seal from appliance store they rott after awhile ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Cdi 1012 dishwasher only installed 2 days ago used twice, when switched on it goes through start up and when prog starts alarm comes on after 5secs checked water supp ok,waste pipe ok filters ok,what else can I do ?


Your appliance should be under warranty. Contact the manufacturer for warranty service. ... Candy Dishwashers

Brand new FGHD2433KF1 dishwasher installed under granite countertop using side mount kit. Will work only intermittantly. Have had repair people here but it worked fine for them. Electrician came and determined that there is power to the unit but no panel lights. When door is shut , no lights but washer makes grinding noise. What do we do now?


... Frigidaire Dishwashers

I have a Belling IDW604 dishwaher just installed in my kitchen. Have only used it a couple of times and have noticed quite a lot of water left in bottom when program has finished. If I then do a quick rinse program the water will disappear. Is everything ok?


There should not be water in the bottom. It's possible it's not draining completely which usually means a clogged hose. It can also be there is something under the screen filter that has blocked the hole. Also, I had installed one that didn't drain c ... Dishwashers

Bad i bought the 1800 psi washer 2 years ago the head on the hose blew off you sent me a new hose it did the same thing. you sent me anouther hose and it blew off too. finaliy you sent me a hole new washer because of a recall. i didnt get to use the first one all year and now i was going to use the new one the other day 3-28-09 and it is the same washer i had and the head blew off so now i have two washers with no hose, that i can not use. so what do i do now ?


... McCulloch FHH18A Electric Pressure Washer

Is it straight foreward to install Bosh srs55co2gb dish washer


... Bosch 18 in. SRS55L02 Logixx Slim-Line Free-standing Dishwasher

My Dishlex global 300's rinse light is flashing after 5 mins use. About 2 inches of water stays at the bottom of the washer. Bought this second hand and it has not been used for a few months. Do I need to fill the reservoir under the washer or lean it at 45 degrees to dislodge anything in the sump. If you have had the problem of the washer starting its program and then stopping after 5 minutes and the rinse light flashing I would appreciate your advice. Cheers Hyph


The flashing rinse light is an error code. I am assuming that your control board is good because the lights are working. I'm also assuming that this model has two pumps. One for filling and one for draining. The rinse light flashing is probably i ... Dishwashers

I have a Karcher 550M pressure washer and was using today when all of a sudden the water started to pour through the handle hence lost the pressure of the water. Is this a rubber washer issue or the gun needs replacing or simpler than that. To be honest although I have had the washer for about 3/4 years now It is hardly used. Also can I fix it and where would I purchase the allen key to replace. Thanks Brian


... Karcher Pressure Washer Gun 91120200 91120200

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1197 seconds