Having problems with your Dishwashers ?

Kenmore Ultra Wash dishwasher model number 665.1374 or 665.1384 I am a technician. This unit does nothing. It has power and ground. I have tested the door switches. They test good. If I unplug the unit and plug it back in then it will run a drain cycle, at least that is what I think it is doing. The motor runs for about 4 minutes. Once it shuts off, there is no further response. No control indicators illuminate. No response from pushing any of the touch buttons.


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore Ultra Wash dishwasher model number 665.1374 or 665.1384 I am a technician. This unit does nothing. It has power and ground. I have tested the door switches. They test good. If I unplug the unit and plug it back in then it will run a drain cycle, at least that is what I think it is doing. The motor runs for about 4 minutes. Once it shuts off, there is no further response. No control indicators illuminate. No response from pushing any of the touch buttons.


... Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Our moffat quiet 2 dishwasher has recently developed the problem that the dishes are not cleaned properly. It does drain water. We've opened the drain cover to check that. There does not seem to be a problem there. We've also started hearing a buzzing sound that lasts a minute or so between cycles. (Not between every cycle though) It's random. We rinse our dishes thoroughly before running a cycle. This unit is approx. 5 years old. Any suggestions?


Check to make sure there are no obstructions blocking the washer heads from spinning. ... Dishwashers

Dish Washer, Electrolux Home Products, Model FDB2510LCC0, Serial NO: 7H34962223 Machine does not drain or add water. The machine has been worked for a couple of years. I checked the following: 1. Overfill Protector not stuck 2. Motor turns on and the machine cycles correctly 3. Since the machine has been running correctly the unit is hooked up correctly: hoses, garbage disposal, knockout plug. Again everything has worked and the motor does cycle and the machine will perform the different cycles


... Electrolux 23 in. ESI602 Free-standing Dishwasher

Bosch D/W model # SHU9955UC. The drain motor will not stop running. Ran the reset sequence on the panel. Display reset to "0" minutes. Power cycled the D/W and when powered back on the drain motor started up again. What do I do ?


Hi ....This is a common problem. Remove the kick plate you will see the white base which also is a tray to collect leaks or backups. Reach your fingers over the top of tray and feel for water/wetness,if so safety switch has been activated and pump wi ... Bosch SHU9955UC Built-in Dishwasher

On last run, did not finish cycle (no final drain) but began a loud rhythmic clicking (from controller area) that stopped after several minutes. Now, no response at controller buttons--no lights/power. This machine is about 5 yrs old and has run perfectly up to this point.


The front panel control board has got short internally.the control board needs replacement.but in the control board section there is a minute fuse located if that fuse blows you will not get light on control board.replacing the fuse will make it work ... Siemens 24 in. SL84A302UC Built-in Dishwasher

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a gaggenau gi976-760 when i start the unit it seems to run through a drain cycle then it does nothing for about 10 min then i hear the drain cycle again never seems to run wated into the unit for wash or rince.. What can i do??


... Gaggenau GI976-760 Built-in Dishwasher

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

Problems with Danby DW1899WP. My husband and I ordered it from Wal-Mart online and picked it up yesterday. We've read through the manual several times, filled all the appropriate receptacles, plugged it in, hooked it up to the water, loaded it, set it, started it, and it doesn't work. It runs the pre-wash rinse for about five minutes before giving a series of beeps, draining the unit, and switching straight to the dry cycle without actually washing the dishes. Help!


... Dishwashers

My dishwasher SL34A015UC / 29 does not complete it's cycle. The cycle will stop with 1 minute left in the rince cycle and continue to run for hours, showing just one minute left. The dishes are not geting clean and there is a unplesent odor inside. I can hear the water draining during the cycle. The drain line is clear and there is plenty of water in the dishwasher. Any thoughts?


... Siemens SL5A70UC 24 in. Built-in Dishwasher

My KitchenAid dishwasher (model KUD101TJWH0) suddenly is making noise from the motor area while inputing water into the unit, whether in the rinse or washing cycles but makes no noise in the draining cycles. I have pulled the unit out while still connected, cleaned any debris from the filter screen below the lower water spokes and can hear the noise very plainly by the motor but I know how sound can travel with the piping. Is the sound only coming from the electric drive motor attached to the


... KitchenAid Dishwashers

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

Dishwasher drain is hooked to a food disposer and until recently the unit worked fine. Last week following a cycle a couple of inches of water did not drain out. All food is removed from dishes, silverware, etc. prior to loading and the food trap in the bottom is completely clear. I ran the unit empty through a Lightwash cycle and afterwards the water level (that which didn't drain out) looked to be the same as before. The dishwasher is run 2-3 times weekly whereas the food disposal is


Hi, The I don't think the problem is with the loop and the 32" above the floor.If the dish washer was removed from one house to another, did *********** ever have a dish washer in the house before that he replaced this one with? The reason I am aski ... Dishwashers

Gets to the end of the cycle (1 minute left on countdown) and just keeps running, does not start the "dry" mode. will run until i open it and when i shut it it goes 13 minutes left on the countdown but then gets stuck at 1 minute again. does not drain. has been doing this awhile, but until now it would simply finish the cycle when i opened, closed and reset it. now it just gets stuck again.


Hello,Welcome to FixYa.Based on your description ... Bosch SHU5315UC Dishwasher

FDB750RCC1 When I start the DW, the motor hums loud then soft then loud then soft...if I advance the dial some sections of the cycle nothing will be running and others the motor is on, but no water is getting into the unit. I just replaced the inlet valve and solenoid and that didn't change anything. I can see water in the recirculating pipe running up the unit, but it will just try to make it up and fall back down. Not sure how to proceed...my thoughts would lead me to the main motor, but


Can you hear the water solenoid click when it calls for water? If so, check that the water source valve is on and water comes out of the valve. Check the entry hose for kinks. Remove everything under the lower arm down to the deck keeping track ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

Problem with ASKO 1385 dishwasher. Unit has manual cycle knob, not electronic. Clock/timer seems to work normally but no water is pumped in and a motor runs continually throughout cycle, even during drying time. Motor continues to run continuously after end of cycle.


CHECK THAT THE WATER IS ON TO THE UNIT, AND IF VOLTAGE IS AT WATER INLET VALVE. IF VOLTAGE THEN WATER SHOULD BE COMING IN EITHER BAD INLET VALVE OF CLOGGED SCREEN IF THERE IS VOLTAGE TO VALVE. NO VOLTAGE THEN CONNECTIONS OR TIMER WOULD BE NEXT. ... Asko 1385 Dishwasher

I have a mod KDSU01DJ that will not drain. I've had it all apart, there are no clogs, nothing stuck. I bench tested the motor and the pump, both run ok. It seems like the pump isn't pushing hard enough. Should the motor be running with the pump during the drain cycle. I"m stumped. Thanks.


Yes the drain pump motor must be running during the drain cycle.This manual will help trace your problem.4317196.pdf ... KitchenAid KUDS01DJ - Multiple Color Dishwasher

Kenmore Elite dishwasher Model #665 1597 2992 Machine fills with water but thereafter it neither washes nor drains. Machine will not drain when I advance the cycle by pressing the Cancel/Drain button. There was a report that there was some noise when the machine first failed. I do not hear anything when I try to run a cycle. What might the problem be? How does one turn the motor manually to see if it is bound up by something? If it is the motor do I want to pay an extra $70 to $100 and


... Dishwashers

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

I have an older Maytag model #WU482. For some reason it will not drain and will only run using the economy mode. I can hear the timer ticking at all other cycles and it does click between cycles. I recently replaced the drain float and the machine had been working fine after. The motor is working and the belt is good. I think the kids were playing with the timer knob. Could this cause a problem with the timer motor? Or does this sound more like a pump out issue, impeller? I'm thinking its


First,inspect the drain float. Make sure it rides on the micro switch correctly or it will not take on water.Check the float micro switch for continuity. Check for power at the water valve when it calls for water. Remove the wire harness from the tim ... Maytag 24 in. PDB1420 Built-in Dishwasher

I HAVE A 8 YEAR OLD KENMORE ELITE (WHIRLPOOL) DISHWASHER . THE THERMAL FUSE BLEW AND I REPLACED IT AND THE MAIN CIRCUIT BOARD. NOW THE UNIT APPEARS STUCK IN CANCEL 2 MINUTE CANCEL/ DRAIN/MODE AND THE RELAY CLICKS ON AND OFF TO THE DRAIN MOTOR. I HAVE BENCH TESTED THE DRAIN MOTOR AND IT WORKS FINE WHEN IPT 120VOLTS DIRECT TO IT ANY SUGGESTIONS . WHAT AMPERAGE SHOUD DRAIN MOTOR DRAW?


Hi\015\012\015\012\015\012The drain motor is of 120 V, 50-60Hz and 0.6 amp rating. Dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visibl ... Whirlpool Dishwashers

When I start the top drawer it defaults to 5 minutes (with the lights Heavy, Fast, Rinse highlighted) runs for a couple minutes, then stops and the LED starts randomly cycling through all kinds of codes very quickly. There is water in the tub that has not drained after completing the couple minutes of operation. This cycle repeats itself if I hit the power button again after the LED starts freaking out. The 5 min cycle shows in the LED, sometimes with the no circulation error, sometimes with the


Here is the solution: \015\012http://applianceguru.com/forum1/24814.html ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1819 seconds