Having problems with your Dishwashers ?

I just installed my Moffat dishwasher and the normal and dry buttons are flashing...help!


Answers :

Defect in dish washer ....return and buy a whirlpool ....it def does not pay to try and save by buying the inexpensive moffat ...you need to spend around 500 to get a good one ...kenmore by sears is another good choice
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I just installed my Moffat dishwasher and the normal and dry buttons are flashing...help!


Defect in dish washer ....return and buy a whirlpool ....it def does not pay to try and save by buying the inexpensive moffat ...you need to spend around 500 to get a good one ...kenmore by sears is another good choice ... Dishwashers

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

"Runaway Dishwasher" Brand new model#FDB520RHS2 Frigedaire was installed today. It was on normal wash and did 8 washes and rinses. It wouldn't switch to the heat cycle. I hit the cancel button after 2 and half hours of washing and rinsing. The water emptied. I then opened the door and let it air dry...I am upset that it did this crazy thing. Do I have a lemon? What would you suggest???


Ask for warranty repair or replacement. ... Frigidaire PLD4375RFC Dishwasher

Kenmore dishwasher ultra was quiet guard 3 model 56516012403 control panel will not activate red lights blinking on normal wash and cancel drain. did the hold the heat dry button then the normal wash button, it stopped the blinking but the dishwasher will not engage when you push any button


That would be model # 66516012403 correct??you may have inadvertently set the lock on function.. check this out from your manual...Lock OnUse the Lock On to prevent unintended use of the dishwasherbetween cycles. Y ... Kenmore 15912 Built-in Dishwasher

Dishwasher malfunction I have a Kenmore Ultra Wash Quiet Guard 3 dishwasher. One day, I found it with a blinking green ?clean? light. I went online to search for the manual, almost impossible to locate. Found a website where another using said to hit a 4 button sequence of ?heated dry? ?normal wash? ?heated dry? and normal wash. After this sequence, all lights went on and something that looked almost like a ?demo? sequence began (not sure now what that was). I hit ?cancel/drain? and it proceeded


Hi,The flashing light indicates that the control did not sense a 3 degree temperature rise with an 8 minute test. There are many reasons this could happen with a working heater. I put together a page that shows the reasons and you might b ... Kenmore 24 in. 15689 Built-in Dishwasher

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

I have a whirlpool quiet partner II dishwasher model # DU1055XTVB5 and the normal light is steady flashing I have did the sequence to reset HEATED DRY NORMAL HEATED DRY NORMAL and the normal light continues to flash and if I push the cancel/drain button then it starts a steady flash


... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

Kenmore ultra wash quiet guard dishwasher, the pots and pans and the normal wash button are blinking. The start and cancel and smart wash out tons have a faint light glowing. Thoughts? I tried the sequence of pressing heated dry, normal wash, heated dry, normal wash and that did nothing. I've flipped the breaker too. I was in process of taking it apart to clean filter, thinking that would help, but lost my manual and now I can't get that off to flea either:(. Sig


... Kenmore 24 in. 15689 Built-in Dishwasher

Viking dishwasher, after pressing normal cycle button, then the start button, the dishwasher begins to run (doesn't seem like there's water enters), then it runs for about 5' and shuts off by itself, the entire cycle is about 5-10min. When I open the dishwasher, it seems dry and the dish detergent door didn't open at all. What should I do to correct this or where do I troubleshoot?


... KitchenAid 24 in. KUDI01TJ - Multiple Color Built-in Dishwasher

THe ProScrub light is steady, and the dishwasher does not work. When I push buttons, the light keeps going off, and with the next button push, it goes on. If I leave the dishwasher like this for a while, then a couple of the other lights, I think the Normal and Heated Dry lights will blink continuously. In either state, the dishwasher does not work.


... KitchenAid 24 in. KUDS02FR Built-in Dishwasher

We have a stainless Frigidaire Dishwasher model FD882040FC3 that is 2 years old. When we hit the "normal wash" button and then "start" button, as soon as the water is in and starts to wash, the dishwasher immediately stops and both "Hi-Temp Wash" and Air Dry" buttons begin flashing on and off. Any suggestions on how to fix this? Kind regards, Greg


... Frigidaire Dishwashers

Kenmore Elited Ultra Wash dishwasher Model No. 665.13859K601 The normal wash button is flashing. I pushed the cancel/drain button and it stayed on. I've turned off the circuit breaker and tried pushing some button sequences as recommended on the internet. I can't access the tech sheet because of they way the dishwasher was installed.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

My Kenmore dishwasher has the lock-on light that is stuck in the ON (lit) position freezing any other action. I have tried cancelling it, shutting off the power and resetting it with the "Heated Dry - Normal-Heated Dry-Normal" pushing of the buttons with no success. Ideas?


I held the "Heated Dry" button down until the lock light went out. It may have been 10-15 seconds. All seems well now. ... Dishwashers

I have a brand new whirlpool DU1055XTV5 dishwasher, installed two days ago. After the cycle completes there is about 1/2" clean standing water left in the bottom. It is not just down in the well area, the whole bottom is covered with water. This is after running a normal cycle with no other options such as sanitize or heat dry. I called Lowes, the store that sold/installed it, and they said this is normal in new dishwashers to keep the parts wet. They said as long as the water does reach th


... Whirlpool DU1055XTS Built-in Dishwasher

I have a kenmore dishwasher model 58715199400. the clean light keeps blinking. ive seen posts that say to press heated dry, normal wash buttons repeatedly until all lights flash. my model doesnt have a normal wash button, it has a rotating knob instead. any tips?


... Kenmore 24 in. 15199 / 15194 / 15192 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2323 seconds