Having problems with your Dishwashers ?

I have just installed a new melie g1243scu dishwasher when i turned it on it came up with a F70 fault (water proof system) how can i reset it


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have just installed a new melie g1243scu dishwasher when i turned it on it came up with a F70 fault (water proof system) how can i reset it


... Dishwashers

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

Just had a reveser osmosis system installed, #GXRM10G. Five blue lights appeared when the battery was installed. Water ran into it for 6 or 7 hours; however, a day later it continues to run water with the constant sound of water going down the drain. Is something wrong? Shouldn't it turn off when filled?


Dear customer,\015\012 check the following and see whether your problem is solved\015\012\015\012Inspect the seals for the main tub, float, heating element and blower diffuser \015\012 ... GE Dishwashers

Our Asko 3530 dishwasher is giving us a 'water inlet fault' code. The machine goes through the pre-drain at cycle start then begins to fill, continues until it's full then kicks out the fault code. I have changed the inlet valve, reset the system to factory default and taken off the lower front panel, finding the overflow area to be dry. Is it time to call for service or is there something else to try before spending the big bucks?


Hi,This sounds like either the overflow sensor or the water control valve is stuck.Usually the valve is a solenoid valve that controls the entrance and fill of the water. If the overflow sensor is underneath, there may be wate ... Asko 24 in. D3530FI Built-in Dishwasher

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

My Samsung dmt300 had an leak on the outside hose with water coming out every where. I shut off water and fixed the leak. When I turned on the dishwasher a blinking heavy lite button came on. This error code means leakage How do I reset the sensor. The dishwasher worked fine before the outside leak .Please help, I don't want to call a repair person!


... Dishwashers

We have a Blomberg dishwasher. We came to a finished cycle to find water in the bottom. We have removed the water by hand, cleaned the filter and the hose. The lights come on, but it doesn't respond when trying to run a cycle. It will do it's ''finished cycle beep sequence'' at the end of the cycle that it didn't actually run. We have reset it by holding down the start button. Turned it off and on, etc.


I am curious what the repair guy found. We have the same problem. ... Dishwashers

Dish draw DD603 showing F1 error and spanner - turned off water and power - tried resetting several hours later, still came up with meswsage after 5 mons


Software error, check it out through sompany exper repairer ... Dishwashers

I have a pldb998cc0 frigidaire. The tech who came out told me the problem was the control panel and that they don't make them anymore. There is not apparent arc marks so it did not short out. We have turned it on and off to try to get it to reset and all that happens is the front panel lights all go on for 5 seconds then die out. There is no sound at all of pump or water. I talked to the manufacturer and they do not manufacture this part anymore. Any suggestions before I have to pitch it and go


As much as i love what i do i see so many bad techs this guy lied simple! the least he should have done was try another board if he was sure that was the fault he would have its simple electronics fault finding he must have at very least tested the b ... Frigidaire 24 in. PLDB999S Stainless Steel Built-in Dishwasher

Model G2582 SCVi We have F70 fault displayed. Have turned off water supply but drain pump continues to run even with machine supposedly switched off. Is there a way to stop as it will take 3-4 days to get a service engineer here. Note can't simply throw a switch in fuse box as this also takes out multiple other power ponts


... Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

No water is coming thru the water valve to fill the dishwasher. The water is turned on. I had a Kenmore portable dishwasher and we just converted it to a built-in. The electricity is on and the water line installed. When I turn on the dishwasher, it comes on ok but no water is coming into the machine.


Most probable cause a faulty intake solenoid. OK start simple and go from there.If your have power and light etc come on then we know you are good for power. I'll assume that is OK. If\012you are not getting any li ... Dishwashers

Recently installed a GE Merlin RO Drinking Water System. Flow of waste concentrate through the air gap faucet down the drain is considerably faster than the purified water. Adding a booster pump did not solve the problem. Neither of the local service provider listed for my area are willing to prvide help. Any ideas on what to do next? (It's not a dishwasher but water sytems was not listed as a category) Waste water should be stronger than purified water. This system needs at least 60psi to


... Dishwashers

Have a whirlpool washer and it would not stop filling so I turned off the water facets and bailed out the water and then ran rest of water out on spin cycle. I unplugged washer and turn hoses back on and water still came in could it be the "fill valve". thanks sharon


... Whirlpool DU805DWG Dishwasher

I have an Electrolux ESI 6104x. Regularly just after starting the dishwasher as it starts to fill for the first time the water inlet cuts out. If you turn the water off at the mains disconnect the inlet pipe (spilling a bit of water in the process) reconnect the inlet pipe and turn the water back on the dishwasher fills and runs perfectly. This fault used to happen occasionally and now happens regularly.


Disconnect the fill pipe from the back of the machine and you should see a small mesh strainer in side the dishwashers inlet valve. Check that this is not dirty - to clean it pull out the strainer and rinse under the tap. ... Dishwashers

I was replacing my sink faucet today and in the process turned the water off to the dishwasher. Subsequently my girlfriend ran the dishwasher without the water on! Now when I go to run the dishwasher no water comes out (meanwhile I've turned the water to the dishwasher back on). Is there some kind of reset? I accidently touched the coil in the bottom of the dishwasher just after trying to run it and it was hot. What do you recommend? Thanks. Mark


Hi,You need to investigate the following :-\015\012\015\012\015\012\015\012\015\012Drain line/air gap\015\012\015\012A\015\012clog in the drain line or air gap (if there is one) is the usual reason\015\012that a dishwas ... Kenmore Dishwashers

I need a diagram and fixing help for a miele G892 SCU plus. The dishwasher starts up with the intake draining light blinking and the saltpc light on. Then the start stop button turn green on. It sounds like it is filling with water but a few seconds it stops and turns off. I open and no water is filling. I believe it is the water pump, what do you think? How do I install it?


... Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

I have an Indesit IDL 42 dishwasher. It has entered a state in which it behaves like this: as soon as I turn it on, it starts swishing the water around (it doesn't pump it out) and it does that regardless of whether I press any buttons (I have tried Start, Reset, turning the program knob, no difference at all). When I open it in the middle of this cycle, the water drips, and there is plenty of water (about 1 in) at the bottom. I have checked the filter, it is clean. Can you please help?


... Dishwashers

When we turn on the dishwasher there is no water entering the appliance..then it cycles to drain the water and I reset it so the pump doesnt burnout...what could this possibly be and is there some troubleshooting I can do before I call a repairman..the dishwasher has a touchpad front...by the way..the water is turned on..


... Maytag Dishwasher

I have a Kenmore dishwasher (model 363.14478791). I hadn't used the dishwasher in a month. I turned on the dishwasher tonight and noticed nothing was happening, but I was getting a clicking sound. I moved the dial to the right to off. As I moved the dial to the right, there were lots of clicks and clunks. I started over and turned the dial to the start position. Some water went in, but then nothing happened again. I clicked forward one click at a time. Sometimes water came in. Then water star


... Kenmore Dishwashers

Aeg bs45e water heater, heats water for 5 mins and then 'trip' light comes on and pressing reset button does nothing, heater must be turned off for 5 to 10 minutes b4 it will heat water again


... Dishwashers

My Karcher 205 M is leaking water from the bottom of the casing during normal operation. I have bled the system and the water flows through fine until you turn on the motor, then it starts to leak, can you help, I have rung Karcher and been told it sounds like the pressurised motor system faulty and a new motor is £50.- Many thanks, Glynn


... Pressure Washers

Maytag Dishwasher I need the reset sequence for my dishwasher. The power comany had turned off the electric to the house to make chages elsewhere in my house. When the electric was turned back on all appliance came back on except the dishwasher. The dishwasher has a front panel touch pad and three of the panel lights are flashing. I know there has to be a sequence to reset the machine. I also need the peace and quiet in the house since I am the husband and am suppose to know it al


We have a model mdvtt53aww1 and you can push three buttons and will light up the hi temp wash, heated dry and sanitize is there a code make it start ... Dishwashers

My Quiet Power 2 dishwasher does not let water go into the cycle and then it turns itself off. Is there a setting that needs to be turned on--or how do I reset the cycle so water goes into the various cycles.


Check to make sure the drain pipe of the D/W output drain water is higher than at least half way up the tub of the D/w. Just below the top point of the sink drain is best. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1290 seconds