Having problems with your Dishwashers ?

Normal and Cancel lights are simultaneously flashing. Replaced control board but problem persists


Answers :

Could you give me the model number and make of your machine, please?
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Normal and Cancel lights are simultaneously flashing. Replaced control board but problem persists


Could you give me the model number and make of your machine, please? ... Dishwashers

Normal and cancel lights are flashing. no response to keypad at all. Have replaced control board and capacitor but problem persists.


Hi\015\012 \015\012I believe the issue could be the temperature sensing circuits that causes an error code to be generated if a certain water temperature is not achieved in a specified time interval. Try to ... Dishwashers

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no


... Dishwashers

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

Replaced control board on my Kenmore dishwaser 665.13122k703. Still have problem with blinking lights and maybe one minute of operation, then stops and normal wash light blinking again. Cancle drain button only one that works, then normal wash blinks. I have another control board, however before I install it, should I be looking eleswhere the the problem ?


... Dishwashers

Normal, light rinse and cancel button are blinking. Turned breaker on and off with no change. Took panel off and tech sheet to give the codes was not there so don't have it. Repairman with no tech sheet says need new control panel. Is there any way to get the tech sheet online to reset and see if problem persists. Kitchenaid kudu02fr The unit is 4 years old.


... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

Hello expert, We are having a new kitchen floor laid and the contractor moved the Whirlpool dishwasher out to lay the floor under. Since it was replaced into it's normal under the counter spot, green "clean" light flashing in succession with a brief stop then starts again. Not really bothered as long as it worked, but of course it doesn't work - What do you suggest?? P.S. Had a problem app. 2 years ago when someone backed into the control panel, also ceased working and repairman charged ex


Someone grabbed the control panel and knocked it around or flexed it whist moving it in and out of your counter.\015\012\015\012Either the PCB board behind the little buttons flexed and cracked, or the ribbon cable that connects the PCB b ... Dishwashers

Whirlpool Gold Quiet Partner IV Dishwasher, Model GU1500XTKT0, Serial number FL4104935, Type 575-0, during a Rinse Only cycle suddenly the cycle light began constantly blinking, which could not canceled or stopped nor placed into diagnostic cycle or other wash cycle. The repairman checked everything and decided problem was Electronic Control Module, which he replaced; blinking Rinse Only went off, but Normal Wash is now constantly blinking and repairman seemed confused and is wanting to repla


... Whirlpool Dishwashers

We have a Kitchen Aid model# KUDP02IRBS1 serial# FT1404764 The dishwasher will not work and the "Normal" light is flashing. We have had the control panel replaced once already with this similar problem and it worked for a while. Any suggestions? Thanks for you help!


... KitchenAid 24 in. KUDP02IRBS Stainless Steel Built-in Dishwasher

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

Control lights are flashing, normal wash, rinse only and cancel...will not let me start dishwasher, will not let me choose heavy wash, shut off fuse, it reset and went on for about 30 seconds then canceled and starte lights flashing again...


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

Whrilpool Gu3600XTS1 After a power surge the control panel pot scrubber and normal lights were flashing. I replaced the circuit board, thermal fuse and control panel. However, the lights are still flashing. what is the sequence of buttons do I push to reset the system.


... Whirlpool 24 in. GU2600XTP Built-in Dishwasher

My Whirlpool Quiet Partner IV has alternating flashing lights across the front panel where I make selections for the type of cycle. When these lights are flashing, the dishwasher will not operate. We have already replaced the circuit panel and the problem persists. We have shut off power at the circuit box several times with no success. Please help!


Here is the tech sheet\015\012http://www.servicematters.com/docs/w...%208530866.pdf\015\012\015\012Here is a manu ... Whirlpool Dishwashers

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

Problem with my Kitchenaid KUDP02FR dishwasher. Working fine until yesterday, now the Cancel, Normal and Light/China indicator lights are all blinking at the same time. Cannot cancel out or restart the dishwasher. Tried unplugging to reset, but it just goes back to the lights flashing. Thanks!


... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

I have Whirlpool control board part #8267371. The problem is that the dishwasher does not complete a cycle. A green light on the door will flash. From what I understand it indicates a failure in the heater at some point. I replaced the heater and all I am left with now is the possibility that the control board has failed. So my question is this. Are there common problems associated with these boards ? Which components should I be looking at ? I don't have a schematic. Or is there anyone that can


Yeah, I'm in the middle of that, too. There's a thermal fuse you can check with a meter just above the control panel inside the front door. It should be 0 ohms. Then it's the control board, I guess. Looking for the same one myself right now. I'm goin ... Kenmore 24 in. 16032 Built-in Dishwasher

Flashing LEDs All indiactor lights on the control panel are flashing and no response to the keypad. Unresponsive to keypad, random LED's flashing, unplugged dishwasher repeatedly, sometimes random flashing returned, now just "normal wash" flashing, tried suggestion of pushing "off" after reconnecting power, no change in problem yet.


Hi,- If the cause is a "dead not working" dishwasher, ensure that the wiring is properly located and attached to the PCB assembly. Check the door switches, check the main wire harness coming into the d/w. On some assemblies a jumper wire with d ... Maytag 24 in. MDB6100A Built-in Dishwasher

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

Normal light flashing on and off. Pressed cancel, now both normal light and cancel light are flashing. Dishwasher won't start. Can't shut lights off. Tried disconnecting power. Lights still flashing.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. To resolve this you will have to\015\012reset the console. Do this by closing the door and press t ... Dishwashers

I have a Whirlpool Gold Series dishwasher GU1100XTLQ1 and it has a flashing light on the control board. When I hit the cancel button it flashes as well. What could be the problem.


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Kenmore Elite 665.7696 dishwasher - "normal wash", "pots pans" and "cancel drain" lights flash on control panel. If power shut off for some time will work for part of load then start flashing again and stop. Is this a trouble code? If so, what does it mean?


Hi\015\012\015\012This error code appears when either the keypad(Part#1 in below link) or Control board(part#11 in below link) is faulty. You can reset the error codes sometimes by turning Off/On the power, however, this is not a permanen ... Kenmore Dishwashers

Du1145xtpba quietpartner II starts then stops shortly into cycle and the normal wash light just blinks, if you hit cancel then both lights will flash when unplugging/reconnecting ribbon cable from control board it will complete 1 cycle and more often than not will do the same thing


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1249 seconds