Having problems with your Dishwashers ?

Dishwasher not getting water. GE nautilus

\015 Dishwasher no getting water. GE nautilus\015

Answers :

HI. this is a water inlet valve issue. i recommend testing this device. it may be faulty.

To access the inlet valve remove the lower panel located beneath the door. The panel is usually held in place with two screws either above or below the panel. It may be necessary to first open the door to the dishwasher to reach the screws over the panel, then close the door to remove the panel. The water inlet valve can be identified by the water hoses connected to it. One hose will lead from the valve to the pump/motor assembly in the center of the dishwasher. Check that the hoses are securely connected to the valve and that there are no kinks in the hoses which could restrict water flow. There are two wires (four, if it has two solenoids) connected to the water inlet valve. Label the wires and connections so that you can properly reconnect them later. The wires are connected with slip on connectors. Firmly pull the connectors off of the terminals (do not pull on the wire itself). You may need to use a pair of needle-nose pliers to remove the connectors. Inspect the connectors and the terminals for corrosion. If either is corroded they should be cleaned or replaced. Use a continuity tester or multimeter to test for continuity. Set the multimeter to the ohms setting X1. Touch one probe to each terminal. A reading of infinity indicates a bad solenoid that must be replaced. Different brands and models will have various measurements, but the valve should show some resistance if it is functioning properly. If your valve has two solenoids, test the second one in the same way as the first. If the solenoid is working properly, but water leaks through the valve even when the dishwasher is off, then the valve itself is the problem. Debris may be preventing the valve from closing. If the valve cannot be cleaned, it will have to be replaced. The valve can also fail mechanically. So even if it passes the electrical test, it may still require replacement. If you have ruled out all other possibilities, go ahead and replace the valve.

(((Make sure you get water to the dishwasher. Check to see if the water shut-off valve (located under the sink) is open before you proceed with the above test)))
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a G E Nautilus dishwasher that has been in storage for 2 years. Every thing works but the Drain. When the cycles are finished I' m left with a dishwasher full of water and it dont drain. I checked the bottom as u said in a previos question I see not obstacles, trash etc. How else4 can I get it to unplug? Also where can I get a owners manual? I can be contacted at [email protected] if needed. Thanks ahead of time for the help.


Hello. Here is the link to a free manual http://kitchen.manualsonline.com/manuals/mfg/ge_appliances/ge_ap ... Dishwashers

Dishwasher not getting water. GE nautilus


HI. this is a water inlet valve issue. i recommend testing this device. it may be faulty.To access the inlet valve remove the lower panel located beneath the door. The panel is usually held in place with two screws either above or below t ... Dishwashers

No water is getting in the dishwasher - GE Nautilus 24" Built-in Dishwasher


Hi,Here is a tip the will elaborate on your problem more, but the bottom line is that you need to replace that fill valve...Dishwasher ... GE Nautilus 24" Built-in Dishwasher

Asko diswasher Dishwasher will not get water. Lines all checked, water on. Pump runs even when in off. Problem started when there was a water clog in the sink next to the dishwasher, and the dishwasher backfilled with water. We used a shop vac to get the dirty water out. Next day tried to use dishwasher, runs, but no water and empying pump will not stop running. Ideas?


Check for water leaks or not draining/overfilling fault ... Asko D1776 Stainless Steel Built-in Dishwasher

No water my kenmore dishwasher is not getting any water. when we try to select normal wash or water miser cycle, the motor turns on, I can tell water is getting to the dishwasher because i can hear it running under the sink and feel it in the flexpipe that feeds the dishwasher. It is not getting anything inside though. Just wondering if you have any ideas. Thanks


SOUND LIKE YOU HAVE EITHER A FLOAT THAT IS STINKING OR A WATER INLET VAVLE THAT HAS FAILED. THE FOAT IS THE LITTLE MUSHROOM LIKE DOME WHICH IS PLACED AT THE FRONT LEFT SIDE UNDERNEATH THE BOTTOM RACK PULL UP GENTLY ON THE FLOAT UNTIL U HEAR A CLICK ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Does not get water - GE Nautilus 24" Built-in Dishwasher


HELLO THERE:when you do not get any water you need to first check to see that the unit is getting water to it and if it is than check out the water supply solinoid valve if this has failed they fail in the closed position and will not le ... GE Nautilus 24" Built-in Dishwasher

GE Nautilus My dishwasher is approx. 6 years old. It has recently started having this problem. On the second cycle (the one where the little door inside opens and release the soap) does not want to work right. The door will open, but it is like there is no water spraying to spread it out. The soap (I've tried both liquid and powder) sticks and drys, running down the door and in the bottom of the tray. I have to open the machine and add the soap to the bottom of the machine if I want to get my di


Smoking from GE (Model:gsd3725f00bb) dishwasherWe moved in an old house, the dishwasher had been installed. but today we found smoking from the dishwasher and smells burned plastic. Could you have any resolution for me? or this problem is popul ... GE Nautilus 24" Built-in Dishwasher

We have a multi-family home and all units have new Nautilus GE dishwashers. Our second floor tenant is complaining of water not getting into the unit. We have tried unsuccessfully to figure out the problem. We are not having a problem with the other two.


There are two reasons that may cause the water not to enter the unit.\015\012\015\012 Water-inlet valve. It lets water enter the machine. If this valve is\015\012defective, you need to completely replace it. It's usua ... GE Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

Water jet arm does not work water goes into the dishwasher dishwasher drains but the arm does not work the dishes are not getting sprayed with hot water the dishes are not getting cleaned the soap in the dispenser does not all come out


In most units, the movement of the arm is powered by the water. If the water does not come out of the arms, check the filter for debris or the arm itself. This could also be caused by mechanical issues. You may want to inspect the arms itself for ... Dishwashers

GE Nautilus Dishwasher Start Problem (no water filling)


Model # should be on inside of tub wall....but any way...This is a typical GE problem which I have seen many times...When a DW\015\012sets for a while not being used...the motor often freezes up....Take\015\012the front (lower panel off.. ... GE Nautilus 24" Built-in Dishwasher

I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.


... Whirlpool DU1055XTS Built-in Dishwasher

It appears that the dishwasher is not getting enough water. I have made sure that there is nothing blocking the door area so that the soap can dispense and I have reduced the amount of detergent to maybe a 1/2 Tablespoon. Have tried both powder and liquid detergents. Ran a sani clean cycle with the Jet Dry product for dishwasher used in the rural. I also run the hot water in the sink prior to starting the dishwasher to ensure the water is hot when it comes into the dishwasher. The detergent


Hello,Welcome to FixYa.Based on your description you`re experiencing the ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Balay dishwasher Hi My dishwasher is broken.When I switch it on nothing happens.I have checked that the dishwasher is plugged in and the water is turned on.I used some hot water to try and get the dishwasher going.It mamaged to activate the sprayers and drain the remaining water.I suspect the water inlet solenoid is faulty! Can you please help me? Thanks, I look forward to hearing from you soon! Regards Alan


... Dishwashers

Dish-washer My dishwasher is not draining all of the water out of the dishwasher after it washes. I got someone to look at the drain pipes and he cleaned out the stuff and they still will not drain all of the water. I would like to know what I could do to get all of the water out of the dishwasher so that the water will come out of the bottom of the machine. Wanda


The problem is most likely that the pump empeller had been damage by pieces from a broken dish or a small piece of siverware. The only way to fix this is to take the dishwasher apart and replace the empeller. If you choose to do this yourself, you sh ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I changed my water control valve, thinking my dishwasher was not getting water, however, if I put water in the basin, dishwasher pumps the water out, however, it sounds like the dishwasher stays stuck in the drain mode, pump just continues to run?


Hi,\015\012\015\012There is a simple explanation for this - water is leaking into the bottom of your dishwasher under the washing compartment. This has caused the float to rise and trip the switch which activates the Aqua-Stop / anti-floo ... Bosch SHU9915UC Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

GE Nautilus Dishwasher Model #GSD4200J00BB Filling with Water


... GE Nautilus 24" Built-in Dishwasher

My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!


... Electrolux Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1395 seconds