Having problems with your Dishwashers ?

Dishwasher will not start after change in electric meter outside. Dishwasher "popped " when it was started Check all circut breakers etc- all fine


Answers :

If you have 120volts at plug,chk for a breaker inside unit and again voltage inside unit at terms on cord,then if so chk motor for a breaker on the motor,some have built-in breakers,then check door interlock switch for continuity and proper operation, then if electonically controlled check for a fuse and burns on the circuit,you may have suffered a voltage spike,and do it soon,the power supplier may be liable if you can prove he disconnected the neutral and you only had 240volts,this could be a cause also as it becomes a voltage divider circuit w/o the neutral connected
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher will not start after change in electric meter outside. Dishwasher "popped " when it was started Check all circut breakers etc- all fine


If you have 120volts at plug,chk for a breaker inside unit and again voltage inside unit at terms on cord,then if so chk motor for a breaker on the motor,some have built-in breakers,then check door interlock switch for continuity and proper operatio ... Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

Our dishwasher just died. It quit. the lights on the top won't come on and when you push them, nothing happens. It started and ran fine earlier, and when my wife checked on it...it was dead. There is a little bit of water in the bottom that didn't drain. What is the problem? Also...I checked the breakers and they are all good. Tom


I would check if your getting power to the motor ? Follow the electrical cord that you plug into the outlet you will have to take the cover off.Your going to have to use an electrical tester follow the cord all the way to where the wire connects.( Ma ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a whirlpool DWH B10W. Last week the main drain outside blocked and none of my service machines were working (not draining). The main drain has now been unblocked and every machine except the dishwasher are now working fine. The plumber has checked the drainpipes again and says all are now clear. When I try to use the dishwasher, after the initial drain it stops and starts beeping at me. I have also noticed that no water is going into the machine. What's happening?


The error most likely indicates a Long Drain Sequence (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. \015\012 \015\012 \015 ... Dishwashers

My GE Profile dishwasher which may be 10 years old has worked perfectly until today. We push start and nothing happens. We have checked the breaker box and all appears fine. What else should I check?


Check for a blown fuse or ... Dishwashers

Bosch Dishwasher I have a Bosch Dishwasher that is a little over a year old. Loaded it up and ran it last night. Got up this morning to unload it, and load it again. Got it all set and went to start it but there is no power. The circut breaker looks fine. But no power to the machine. Not sure what is going on, or what needs to be done. Thanks....


... Bosch SHU3306UC Built-in Dishwasher

Dishwasher won't start i checked breaker etc.


Try this. If you have a gfi outlet in the area of the dishwasher make sure its reset and working a lot of times the dishwasher line is run on the same line. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My kitchenaid dishwasher won't start, no lights go on, it stopped in te middle of the cycle. The circuit breaker was checked and it seems fine.


... KitchenAid Dishwashers

My Frigidaire dishwasher has no power. Checked breakers etc. All is fine. Could it be on delayed wash? How is that turned off?


... Frigidaire 24 in. FDBB944C Built-in Dishwasher

See below This is a post that I just copied to this space "I have a whirlpool Quiet Partner II, Model GU2400XTB1, that just suddenly will not start, as if the power was cut. Circuit breaker is fine. from the little Internet research I've done it looks as thou it could be a thermal fuse problem. How easy are these to replace, assuming that's what it is?" Mine is quiet partner III ... there is power to the connection box at the dishwasher it self (checked w/ light tester) ... but there is no power


Have you tryed leaving the power cord out of the socket for an hour or so sometimes they don't lose the memory until they have been left disconnected for a while ... Whirlpool GU2400XTP Built-in Dishwasher

Is there a fuse or a circuit breaker in the Kenmore Ultrawash, quiet guard4 smartwash dishwasher purchased about 3-4 years ago? There is no power going to the machine--the outlet, the circuit, etc are all fine--but no lights light up on the panel and the washer wont start. Any suggestions?


There is a fuse behind the control panle its white and 1 inch by 1 inch ... Dishwashers

The ge profile dishwasher model PDW8280J10SS was purchased about 2 yrs ago. It was working fine up until Jan. 2009. It ran fine but the water stopped draining. I read were you should run the garbage disposal prior to running the dishwasher. I drained the water and did this. It worked fine for a while then the problem was back. Once again, Drained all the water, sucked it out with a turkey baister, moved the dishwasher and checked hoses etc. Once again, it worked fine for about 10-14 runs. It now


It is probably clogged at the pump or before. See if you can get outlet hose off the bottom before the pump. ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Dishwasher fills with water and then stops. No lights are on at all. I cked wiring and circuit breaker and no issues there. I then flipped off circuit breaker over night. Got up next morning and flipped breaker back on. Dishwasher lights were on and when I pushed Start button, it ran fine. Now it is doing same thing except circuit breaker trick dont work like last time. THERE is NO issues with wiring or connections to dishwasher.


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

My dishwasher will not start. It is a frigidaire / electrolux FDB1050REQ. I have checked thepower....and reset the circuit breaker.......then pushed the start button.....the light comes on on the front of the washer like normal but no water starts filling. I have jiggled the anti water overfill device but still nothing. HELP!!! The front of the dishwasher says Frigidaire, however, the inside of the door where the model# is says Electrolux


... Frigidaire Dishwashers

My dishwasher so my dishwasher seemed to have quitworking during a cycle. like breaker triped or something. i checked the breaker and thats fine. it seams like its hard wired in though. Would that be right? and is there a fuse or something that could/would blow during a wash? I dont know what model it is or anything it was in the house when i got it. The dishwasher is built in and it seems decently old its a kenmore ultra wash and it has like 10 buttons for the differend cycles on the left and a


Sounds like the fuse on the control blew. you can replace the fuse for\015\012around $20 or you can cut and splice the wires for free. If that doesnt\015\012work then you may have a loose conection in your junction box under the\015\012dishwasher. ... Kenmore 24 in. 15932 Built-in Dishwasher

Candy csd-68-80 all four lights on front panel lit, started flashing within few seconds of switching dishwasher on, no previous problems,dishwasher not overfilled, checked manual which said too much inlet water unsure what this means or how to check it. do all usual cleaning,salt,arms etc. had dishwasher about 14 months and use it every day never had any problem before


... Candy Dishwashers

I have a Kenmore model 587.1610 dishwasher that doesn't fill all the way when starting a load. I checked the float switch and it is working fine. The fill soleniod is also working fine and is clean. It just seems to time out before it fills all the way.also to compound the problem it doesn't seem to want to start all the wash cycle even after I have re-started the machine and it has filled to capacity. please help thanks Danny


... Dishwashers

Wont start I've had the washer for many years with minimal problem. Yesterday when I closed the door no light went on and the washer would not start.  After 20 minutes or so it suddenly went on and worked fine.  I thought that it might have not completed its last cycle. Today, however, I had the same problem and it's been over an hour and still hasn't started. (I checked the circuit breaker and it's fine)


Give it a firm push over the door latch once you've closed the door..it might be the door switch not activating. oops.... first and formost isolate from power for 5-10mins and try ... Bosch 24 in. SHU43 Built-in Dishwasher

My dishwasher is not quite 2yrs. old and has always worked great until now. Top rack cups and mugs still are dirty inside from coffee, lipstick, etc., glasses have spots and are cloudy, and silverware seems to have streaks and become darker. I always turn hot water on at faucet prior to running dishwasher. I have check the water faucet and it is 120 degrees. After starting the dishwasher I checked and the water is not even 100. After about 20 mins. the water was aprrox. 117 degrees. The


Hello,Welcome to FixYa,Based on your description I`d suspect a plugged wash pump.The place to start for that is to pull the pump filter, spray arm and check for food deposit, broken glass, undesolved detergent and ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Our GE Profile Dishwasher is not working since today afternoon. The electronics seem to be working fine but the water supply does not start on pressing the start button. The dishwasher seems to go on with its cleaning cycle without water. We don't know how to fix this or to even check any plumbing/water supply problems. Please help.


OK First try this below....\015\012\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hu ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Starts cycle, drains ok, then "intake/drain" LED comes on solid for 4 seconds, flashes 4 times, solid 4 seconds, flashes, etc. no water coming into dishwasher. DOUBLE CHECKED the intake filter its all OK ! how do i 'reset' the machine? Im pretty sure the sensor is goofed up and needs to be reset but i have tried holding various buttons, start, power etc, cannot figure out how to do it


... Miele G2430SC Dishwasher

BOSCH Dishwasher Problem I have a dishwasher (SHV46C13UC/33) that when I start any of the three cycles it continues to run until I open it and do the 'cancel' function. The 'rinse/drain' seems to be running fine, but there is a film left after that mode. I've checked the water inlet, which is open and fine. And, it does drain properly. Is there a SENSOR I need to clean periodically? Or, is the man control module the problem? What's going on?


I would check the float switch in the bottom should be a mushroom shaped thing that turns the pump off after the water level in the machine has dropped to a certain level or has totally emptied. ... Bosch 24 in. SHV46C13UC Free-Standing Dishwasher

New LG 2131sh dishwasher, have it for 2 weeks, worked twice and now when pushing power lights come on, and when selecting program(eg intensive) it does not start. Water checked at it is fine. Checked door, closing fine.


I would call where you purchased it. There should be a one year warranty on the dishwasher and they should send someone out at no charge to repair it. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2255 seconds