Having problems with your Dishwashers ?

No Water goes into Dishwasher - Dishwashers


Answers :

If there's no water entering your dishwasher, check these:

Water-inlet valve
Float switch
\015\012\015\012\015\012\015\012Water-inlet valve\015\012\015\012The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usually located behind the lower access panel on the left or right side. It's the device with the main water line (usually copper) from the house, a rubber tube to the dishwasher, and two wires attached to it.

\015\012\015\012\015\012\015\012Float switch\015\012\015\012The float switch is a small electrical switch that's located right below the dishwasher "floor." Above the switch, on the inside of the dishwasher, is a plastic cylinder that floats up as water fills the dishwasher. If this switch is defective, or if the plastic float gets caught or trapped in the raised position, the water can't enter the dishwasher. If the float switch is defective, you need to replace it.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Leaking dishwasher The dishwasher leaks a stream of water at the base -bottom left corner whenever it goes into the final rinse cycle. It does not leak when it is in the wash mode. This leak just seemed to develop suddenly. There was no build up -ie a small stream of water. I just noticed a big puddle on the floor one day after dishwasher had completed its cycle water leak in the left side ,bottom ,husband states a small drip,drip and we do not know what to do or replace. No water standing


I just had this same problem and it was caused by a small plastic seal on the bottom of the door. My friend owns an appliance store and he said this is a common problem for this model of dishwasher. The part was $68 and the labor was $60. I could ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Trying to connect Sears Dishwasher model 110733500 Iknow where the water goes in, but can't figure out where the water goes out I see where there is an outlet that might be it but I must be missing a part for it this is a used dishwasher and I don't have the schematic for it. Thanks, Richard


In the space below the door, look on the left side and you will see 2 almost clear drain hoses. One goes to a loop up the side of the dishwasher, the other is tucked into the left frame just for shipping. Gently pull it out and connect to the suppl ... Kenmore Dishwashers

There is gum stuck somewhere in my dishwasher drain line. The water won't go down. I took the inside apart and can see the hole where the drain water goes. I disconnected the drain hose under the sink. I got the water to drain out when there was alot in there, but now it won't drain again. I blew compressed air from a compressor backwards through the hose and it makes a big splash and bubbles inside the dishwasher, but the water still won't go down. I put Boiling hot water and vinager in there t


Ther e is noo easy fix, short of replacing the drain line( if indeed thats where the clog is)although you checked the hose from the under the sink, did you check with in the hole where the sink conection is made??and try disconnecting the drain hose ... Dishwashers

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.


... LG LDF6810 Built-in Dishwasher

I have a Kenmore dishwasher, model 665.17019401 (serial number FS1002610). It goes through all cycles, drains out water, periodically, and dries the dishesat the end. But, when it ends, there is water at the bottom of the tub, at least 1 quart of water. I have to drain out the remaining water in the dishwasher. What is wrong?


Either the drain or screen is somewhat plugged, or a clog or jam in water pump. Many machines do leave just a little bit of water just so the sewer fumes don't come up. ... Kenmore Dishwashers

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

Dishwasher Our dishwasher is not washing the dishes. The water go in and it goes through the complete cycle and dumps the powder in but the water never gets above the dishes or even to the soap holder. The powder is a dry pile below the dispenser. It seems that the spray arm doesn't extend or spray water over the dishes.


I have a kenmore dishwasher (about 10 year old) it won't turn on. It just buzzed when set to wash. What can I do? ... Dishwashers

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

Water jet arm does not work water goes into the dishwasher dishwasher drains but the arm does not work the dishes are not getting sprayed with hot water the dishes are not getting cleaned the soap in the dispenser does not all come out


In most units, the movement of the arm is powered by the water. If the water does not come out of the arms, check the filter for debris or the arm itself. This could also be caused by mechanical issues. You may want to inspect the arms itself for ... Dishwashers

There is a pool at the bootom of my dishwasher when the wash cycle is completed. When doing "Rinse Only", I could hear something come on immediately following the rinse but nothing seemed to happen. I pulled the Dishwasher out and the drain tube is set up so that it immediately goes upward a few feet before it eventualy goes back down to the drain. I noticed that there is water in the tube right next to the Dishwasher before it makes that climb. I'm wondering what all this means...


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012 ... GE GLD5800L Dishwasher

I have a whirlpool gold model GU1500 diswasher. When the rinse cycle ends the water pumps out into the garbage disposal like it should, but then water backs-up from somewhere into the bottom of the dishwasher. The overfill protection drain seems OK...the water doesn't overflow. It doesn't have a air gap on the sink. The drain hose goes directly from the dishwasher to the inlet on the garbage disposal. It appears to be properly installed per the installation instructions. The washer is about 4 ye


Seems you answered your own question here. You need to make an air gap in the drain hose - take as much slack as possible and make a curve (upside down U) under you sink as high as you can go. Make sure you clip ot to back of the cabinet to stabili ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

My 2 year old frigidaire dishwasher is not filling up with water, goes through cycle but no water is coming out, valve is open all the way?


If the\012water flows then the flow should be good, if not the inlet valve is bad or there\012is dirt in the filter. Also check the flow at the inlet of the water line. What\012is most important for the motor to start functioning is that the ... Dishwashers

Our kenmore dishwasher is not draining, you can feel the hot water in the hose where it drains but cannot feel it where it goes into the drain and watere is sitting in the bottom of the dishwasher


You need a new askoll pump to drain the water.this must be installed by qualified person. ... Dishwashers

My garbage disposal badger 1 was just replaced with the same badger 1 disposal. my dishwasher will not drain water anymore. the old one had a hole where the attachment to the dishwasher hose goes but ther isnt one for the new 1 but the hook up is there. Do i have to drill a hole in the new 1 for the water to drain out


I THINK NO :\015\012 THE DRAN PATH MAYBE BLOCKED\015\012 ALL YOU DO 1ST TO SURE THE PLUMPING IS OK OUT SIDE THE M/C\015\012 THEN IF IS OK BE SURE FILTERS INSIDE M/C AFTER YOU OPEN THE DOOR OF M/C PERIODICLY CLEAN AFTER E ... Dishwashers

I have a Maytag Performance dishwasher and the dishwasher is not filling up with water from either of the arms. The motor runs and goes through cycle but not water.


Hi,\012Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Dishwashers

I have a DU810SWPQ Whirpool dishwasher that does not use all the soap in the dispenser when it goes through the cycle. Perhaps the water flow is low through the dishwasher. Is there an access panel to clean out the water lines?


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Whirlpool Dishwashers

My dishwasher will fill with water but when it goes into the wash cycle it makes a noise that is like a grinding or loud hum and it will not go into the wash cycle but it will pump the water out of the dishwasher when you cancel the cycle


Take apart the spray arm assembly at the bottom on the inside. When you get all the way to the bottom and access the spray motor, simply turn the impeller a few times. Put back together and try it now ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Our dishwasher goes through the cycle and finishes fine without water in the bottom. Then within a couple hours, water comes up and sits at the bottom of the dishwasher. Handyman could not figure out why. No clog in place.


Hello Sandra, Welcome to Fixya ! You've come to the right place. The problem you're experiencing sounds like (unfortunately) a common one. The water inlet valve has been an issue with B/S/H built ( this includes bosch, thermador, seimens & gaggenau ) ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

I have a Kenmore Ultra Wash Dishwasher (Model Number 665.15634) that will not fill up properly. When I try to run a cycle (any cycle), the first thing the dishwasher should do is fill up with hot water. But in my case, my dishwasher fills for about 10 seconds, then stops. Then tries to fill again for about 7 seconds, then abruptly stops again. And this process goes on and on and on. The dishwasher never fully fills up nor starts the wash sequence properly. Once the dishwasher fills up, it


... Dishwashers

Dishwasher comes on, fills with water, water heats, no movement of the arms so no water spraying out, then the water drains, it goes through the dry cycle and no clean dishes.


What is the manufacturer and model number of your dishwasher?\015\012\015\012Depending on the model and design, the sprayer motor/pump has probably failed and the drain motor/pump is still working.\015\012\015\012Recommend you pull the sp ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher

Our bosch dishwasher runs but no water is spraying on the inside. Is there a water filter clean out or is there a water pump that might be broken? I checked the line coming in and it isn't plugged. I made sure where the stainless line goes into the electric valve that it wasn't plugged to that point. I could see anywhere else to check if it was plugged. I figure there has to be a water pump, but I guess I'm not sure of that either. Thanks for any help..


Hi, welcome to Fixya. \015\012 \015\012By the description you've provided, it sound's like the wash motor is either seized or just stuck, let's hope it's the later. \015\012 \015\012Bosch had issued a service tip about this ... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1339 seconds