Having problems with your Dishwashers ?

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


Answers :

These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace.
Check to see if the (control lock) is enabled. If it is, then it can be disabled by pressing and holding the (no heat dry) button for 4 seconds. The (lock on) light will then turn off. This may not be the problem but it's worth checking.\015\012 \015\012Your symptoms point to a stuck key or failed control console keypad. A failed electronic control board could also cause this problem.\015\012 \015\012What I would do is contact a service technician from craigslist.com under the services (skilled) section because they are the ones that charge a reasonable amount. Don't call Sears because they often would have to order the part and then you're stuck for 2 weeks.\015\012 \015\012Good luck and I hope you resolve the problem soon :)
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

My Candy DFI85S is not drawing water into the machine. After a short time of trying, the machine stops and sounds three beeps. The tap is definately turned on. Any help or advice would be appreciated.


... Dishwashers

Hi, we have a Hoover HEDS668-80 dishwasher at work. The first problem we had was none of the programs would run this turned out to be a broken door lock. After replacement we managed to get one pre wash and one wash program to run, now when we try it, it starts but after 2 minutes the pre-wash and wash lights flash and the machine beeps 8 times. Can anyone help?


... LG LDF6810 Built-in Dishwasher

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

I've tried to use this new machine 3 times. Each time it was never turned off until I pushed the cancel/drain button. Once I let it run for 2 hours before turning it off. This evening I tried the rinse only button and when I checked on it,it had switched to the normal wash cycle. Then I pushed the cancel/drain button.


If this is a new machine and it's under warranty, Have a technician come out and repair it as soon as possible. then fully test it's operation after he is done fixing it . It sounds to me as though it ... Whirlpool Gold GU2275XTV Builtin Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

The bottom spray arm screw seems to be stripped and just turns , so I'm having trouble removing it. This is the first time I've tried removing it. It is at least 5 years old, but the dishsoap dispenser didn't open this time so I figured it would need cleaning. What do I try now? What will happen if I can't tighten the screw back up. I've tried and it slips. Help Please.


... Whirlpool GU2400XTP Built-in Dishwasher

GSD2200G00WW. When starting washer, part of the time the machine will not start, other times if machine has been running for a while and you open the door and try to restart the machine it will not restart. You can hear the motor humming as if it wants to go but it will only restart if you turn the motor shaft even just a little. I am wondering if the electric motor is dying??


... GE GSD2200G Built-in Dishwasher

I am trying to install a new Maytag MDBH945AWB Dishwasher and have to run the drain hose under the machine in order to get it to the sink. Each time I try to use the hose that comes with the machine it snaps in two and breaks. I have tried to look for a replacement hose that would stand up to the abuse but all I can find is the original. Is there a replacement I can get that is more flexible than the one that comes with it? At this point I am rather embarrased about going back to Home Depot


Hi...home depot sells clear PVC hoses, They come in various lengths up to 100 ft. You can use hose clamps to connect it to the T-fitting. ... Dishwashers

It does not matter which cycle is chosen, once "start" is pushed on our Asko D3120W the drain pump comes on empties the machine, then it fills for the first time, and turns off. It happens on all cycles. We have turned off the power thinking that would re-set the machine, but it has not worked. Do we need service or is there something we can do at home?


Hello &\015\012Welcome to FixYa\015\012\015\012The problem\015\012seems to be with the frozen main pump or the pump seal/impeller gone bad. To\015\012solve this the pump and motor has to be removed and then the part rep ... Asko 24 in. D3120 Dishwasher

My Hoover dishwasher HFI 3015 is not working. When you turn it on, the P1 and 'out of salt' light is flashing and bleeping constantly. I believe that it may have run out of salt yesterday, but I have filled it this morning and there is plenty of Dishwasher salt in the compartment now and it is overflowing with water. I have tried turning the machine on and off, but each time I turn it on I get this bleeping and flashing and can't stop it. Any ideas?


... Hoover Dishwashers

Won start Was using the pressure washer 1st time this year and started on the second pull. Ran out of gas shut-off also noticed it needed oil. Believe, I put too much oil so, I drained some and added gas. At first, there was no resistant in the pull so waited an hour and tried again. This time the resistant was there on the pull but still would not start; no attempt even to turn over. It's been a couple of days...changed the spark plug although, hardware guy said nothing was wrong with it..still


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Have MDB7609AWW2, and tonight tried to start machine and nothing would start. No lights, no activity. We took a look inside and tried to straighten out the top arm cause it wasn't turning freely. Also checked the circuit breakers. Please advise.


... Maytag MDB7609AW Builtin Dishwasher

When I turn on my Turbo dishwasher it goes for about 3 mins then comes up with an E1 error; I've tried resetting the machine, but then the display shows "1h" and "05" flashing three times each. The machine starts and error code above happens again.


... Dishwashers

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

We have a Whirlpool GU980 Series Dishwasher. All the lights work. No matter what setting I use, it fills up, and then nothing happens. The "washing" light will be turned on, but nothing happens. I try to drain the machine, it will make a sound like it's going to begin a process, then it just stops. Do these things just "die" after some time? This machine is 7 years old.


Sounds like something is caught in the pump impeller. you will need to take the pump apart inside the tub. ... Whirlpool GU2400XTP Built-in Dishwasher

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

No matter which cycle selection in pushed, the dishwasher only starts up in the "normal" 93 min cycle. If I try other cycle options, and persist, I get an ER message and the cycle stops prior to the soap powder door opening and never completes the cycle. Only with turning off power for several minutes and receiving the PF message, and resetting ONE TIME that message can I then select any cycle, at which time the machine "defaults" to the "normal" full cycle. If I do not disturb that cycle, it wi


Looks like you are having a good deal of problems with the dishwasher.\015\012\015\012It will be helpful if you provide the make and model no. of the dishwasher.\015\012\015\012At this stage I can speculate the controller (ass ... Dishwashers

I have a Whirlpool ADP 5777 WH dishwasher I need to know if I can reset the dish washer, it is the timer which is stuck, so you can change the dial on the left for the various washes, eco, etc. but the time of the wash does not change!! Stuck at 2 hours 47 minutes!! I have tried turning the machine off at the powerpoint and turning it back on but that has not fixed it


... Whirlpool Dishwashers

Have whirlpool gold dishwasher made in Mexico, the control lock light stays on, when i push it and hold it just blinks three times and then stays on steady and then does the same over and over, before it did this I noticed the lights for different cycles flashing randomly, and even pushing cancel button once in a while would start the machine up....I have tried to unplug the machine and then plug back in, but nothing is helping....any ideas??


... Whirlpool Dishwashers

I try holding the cancel/reset buttons to lengthen the time to allow for better drying. I have followed the directions given in the manuel. It doesn't seem to be working. Could you outline the steps for me... 1.) Hold both buttons down simultaneously... 2.) turn on machine... then what?


... Bosch SHU5307UC Built-in Dishwasher

Our cuisina dishwasher keeps tripping a trip on our main fuse box, the fuse on the plug does not blow however, this is happening every time i try to turn the machine on. it stopped half way through a cycle and wont restart.


... Dishwashers

KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher: Just stopped working before Christmas. I had washed a load a day before, and the next day I couldn't use the Rinse Cycle. The lights turn on for Normal and Heavy, but nothing happens when I press Start. I played with the breakers a couple times, to try to "reset" the machine, but it didn't do any good. I really don't want to be spending a lot of money on that dishwasher, especially after reading all the horror stories abo


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

Hi I am in an emergency situation with an ikea whirlpool dishwasher. I have no idea what model it is since it's built in and I can't find the manual in my rental apartment. The machine works normally until the part where it's supposed to pump the water out after rinsing. At this point it starts to beep, once, and then 3 times. On and on and on. If I open it, there is water stagnated there. If I try to turn it off and back in, it will go through a whole new program and then I get the same problem


Can you feel the pump operate during the last wash cycles? if not either theres a bad pump motor or lack of power to the pump during that cycle,if this is ok,then remove the drain hose to the main drain to see if this is plugged up with food debris ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1517 seconds