Having problems with your Dishwashers ?

I have a dishlex Global 500 which runs for 3-5 minutes then displays nF


Answers :

Nf= not filling. check inlet vale, or fault will be with pressure switch. If you have poor water pressure, you may need to increase the fill time- insructions can be downloaded from:www.electrolux.com.au, click on "customer service", then "download manuals", then Dishwashers-semi integrated, electronic, then download Dishlex Global Part 1 and Part 2.
\015\012Information on setting fill time can be found at the back of Part 2, but Part 1 has a list of the fault codes
I had the same problem, replaced the pressure switch (right hand side), all ok. BUT, Dishlex has changed the hose size on the switch to a much smaller size. Muck about to change hose size.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dishlex Global 500 which runs for 3-5 minutes then displays nF


Nf= not filling. check inlet vale, or fault will be with pressure switch. If you have poor water pressure, you may need to increase the fill time- insructions can be downloaded from:www.electrolux.com.au, click on "customer service", then "download m ... Dishwashers

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishlex Global 500 dishwasher was relocated to a new house upon first run the display showed ND for no drain, the filters are all clean and can manually siphen water out through drain hose so i know there are no blockages. Was working normally prior to disconnection.


When running the drain hose it must be hung from the highest point under your benchtop before draining to the sink waste. ND is sometimes displayed when the hose is not mounted high enough ... Dishwashers

Bosch D/W model # SHU9955UC. The drain motor will not stop running. Ran the reset sequence on the panel. Display reset to "0" minutes. Power cycled the D/W and when powered back on the drain motor started up again. What do I do ?


Hi ....This is a common problem. Remove the kick plate you will see the white base which also is a tray to collect leaks or backups. Reach your fingers over the top of tray and feel for water/wetness,if so safety switch has been activated and pump wi ... Bosch SHU9955UC Built-in Dishwasher

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that


... Kenmore 15912 Built-in Dishwasher

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

Model IGV 659.1 Dishwasher When switched on the 'time display' takes longer than 2 minutes to display the planned wash duration. The display works fine to set a delayed start. After cycling the start delay round to 0, or after RESET (buttons A and C pressed) the unit is then 'nudged' into displaying a time. After, at last, a time is displayed the unit works fine.


... Kuppersbusch Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Hi , i have westinghouse dishwasher model SB915SJ. when i put it to wash on eco normal, it stops a after about 20 minutes and i have to press the program button to start it working again. it's currently running now but it stops about every 4 minutes and the numebr 20 appears in the display screen. if i push the program button it will rung for another 4 minutes then stop, start beeping and the number 20 appears. how can i fix this?


Www.westinghouse.co.nz/...westinghouse/.../NZ_WH_Dishwashers_May06.pdf \015\012\015\012\015\012\015\012Above is your user manual, and below is your service and repair manual.\015\012 ... Westinghouse Dishwashers

Dishlex global 500 pump running continuously


... Electrolux Dishwashers

Bsoch dishwasher runs long and displays 1 minute left on timer


Sounds like a bad solder connection on the heater relay of your control unit. more than likely you will need a new control unit. part number 266746 ... Bosch 24 in. SHU53 Built-in Dishwasher

Hello I have a dishlex 450 global, it was not working properly with no display on the screen when I plugged it in it just beeped continuously with no display on the screen. I pulled the cover off and the active wire was broken and the r56 diode was burnt out also it had a random black wire just hanging there. Is this fixable. my email is [email protected] Thanks


... Frigidaire 24 in. FDB126RB Built-in Dishwasher

I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut


... Whirlpool GU2400XTP Built-in Dishwasher

I have a Dishlex Global 500 dishwasher (DX500lWW*b). Woke up the other night to find water all over my kitchen floor. The hot water hose connector to the hot water tap split (bursted). The dishwater was not in operation at the time but I can only assume when the hose bursted the dishwater came on to alert me? the code on the dishwater is displaying ''oF'' - which means Incorrect fill level of fill time. I have consequently had the hose connector repaired but the display still has the code ''oF''


I found this\015\012\015\012"Hi - answer I was given by Electrolux Help was: pull machine out from under bench onto old towel, tip GENTLY onto left hand side (your left as you face the front of the machine) after it has drained, stand up ... Dishwashers

Dishlex global 450 _ how do i fix fill level time fault? displaying oF? Hi There, I have the above dishwasher and saw your advice on fixing fill levels - my display is showing the oF message and the pump to drain remains on whilst mains is connected. turning off mains does not clear message. holding eco button down does not clear message? is there anything else i should do in terms of removing parts to assist the process? I have cleaned out all of the drainage bowl and all is clear. i would pref


... Dishwashers

Kenmore elite model 16583200 Cycle has always taken too long. LED will display time remaining. A typical cycle will display for 73 minutes and then take 3 times the amount of time to run through.


... Kenmore Dishwashers

My bosch dishwasher control panel displays 0H on the time delay. When I start it the OH go to 2H. It then starts running and does not stop. The cycle minutes don't display. It's model number SHU5302UC 14. I do not have a manual and cannot find one online. Thanks


Check to see if your unit has a recall on it because if it does you will get a free control module from bosch.\015\012your problem is the control module. thermador .com is the site to lookup. gaggenau,bosch,thermador they are the same ccompany. ... Bosch 24 in. SHU53 Built-in Dishwasher

Just had new Frigidaire dishwasher installed. When cycle is started, display shows 99. Unit will fill with water, run cycle for about five minutes, stop and empty water then display a flashing PF. Can not seem to find a list of codes for this.


Pf is means power failure. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

I have a Neff s4457n0gb/32 dishwasher that will not complete the cycle as it finishes on 0:01 minutes remaining on rinse and not moving to drying. I have to press the reset to clear the display to 0:00. If you've any idea how I can correct this problem that would be most helpful.


... Neff 24 in. S4457 Built-in Dishwasher

Miele Optima G 2430 - The dishwasher will pump water in for 5 seconds with the Intake/Drain light flashing 5 times. Then the light stays on for 5 seconds and it does nothing. This process is repeated for about 10 minutes untill the washer is filled to the just below the door with water. Then the washer starts running for about 1 1/2 minutes and drains the water. Then it all starts over. If I let it do this for a hour - The display reads F12 with the Intake/Drain light flashing.


Hi\015\012\015\012The first thing that should be checked is if its draining\015\012properly as it could be that the drain hose is clogged and needs to be cleaned.\015\012The drain pump also should not be clogged. ... Miele 23 in. Novotronic G841 Built-In Dishwasher

I have a Bosch SHU9955US/14 (Integra) dishwasher. There is currently a 0 with and asterisk showing on the display and the unit will not run.


See this causes and fix it. God bless you\012 \012 \012 \012 \012 Thermal Fuse\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Bosch Dishwashers

Global 300 dishlex. eco light flashing, pump running, no water. all of the above continues when door is opened.


Water leak check in the base ... Dishwashers

My dishwasher is 6 years old it started making clicking and knocking sounds about a week ago. The display is blinking crazy at about 37 minutes left in washing cylce it blinks 37, HO, and CL. It blinks other numbers also. The water still seems to be flowing in and out fine. It's heating up and draining when canceled. I'm running it on normal wash and high temp. cycle. It sounds like the sensing parts in the door are going off and on.


... Frigidaire 24 in. PLDS9999CC Stainless Steel Built-in Dishwasher

Dishlex global dishwasher, stuck on eco, eco light flashes and drain pump runs


Try turning the taps on harder, I read that someone else had the same problem and this fixed it for them. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0745 seconds