Having problems with your Dishwashers ?

Problem with Caple Di604. When switching on the power LED lights up (not as bright as prviously) but the program buttons do not work, any ideas?


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Problem with Caple Di604. When switching on the power LED lights up (not as bright as prviously) but the program buttons do not work, any ideas?


... Dishwashers

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Program stops When the machine is switched on it runs for a minuite or so then stops and bleeps and shows blanks - - - - I switch it off and again re-start and it again repeats this as above the filters have been cleaned and the water was drained and again it persists, the machine is 3 yrs old. I tried a sequence described as switching the programm button in 4 quick times but this didnt work either. Is there any other way we can re-programe this dishwasher or is it that there is a fault where so


... Smeg 18 in. DWD409SS Built-in Dishwasher

We have a miele g673vi dishwasher. it will not start. when it is turned on the #2 light flashes, but it does not work. pressing any other program button has no effect. the only button that does anything is teh on/off switch


... Miele Dishwashers

FDW80 the error code DEMO is on permanently and won't let any program run. the refill salt and rinse aid are flashing but they have been filled already. I have tried holding the on/off button and reset button down together but its not working, and i've tried switching it off at the plug and leaving it for a while, but nothing.


When the support engineer says press the 'on/off' button and 'start/reset' down together, press very hard. Press hard for 5-6 seconds and a the wording 'demo off' appears for a split second, then resets its self ready for use. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Won't work When i turn the machine on the on/off button lights up but the program lights don't, any ideas??


I hant not seen this unit but what it sounds like to me is the control bord that controls the functions on the washer may be bad. you should try and find if there is a tech sheet somewhere in the cabinet or under the dishwasher. that will help you to ... Zanussi 24 in. DE6744 Free-Standing Dishwasher

Belling BE601 I Recently came into posession of a Belling BE601 Dishwasher, no Manual as is second hand. The condition of the dishwasher is as good as new, but when the door is closed after setting the program, nothing happens, it will not start up. I have checked the door switch and it is working ok, any ideas ?


Reset the display to -.if there's a number there it's the length of time later it will start at.both the start and the program have to be selected together..........but you also have to reset it after the last program ... Dishwashers

Hi, I bought a second hand prima lpr 450 dishwasher, and I switched it on, the light is on, but I can not get it to work, the button ''program'' does not do anything. Please, help.


Hi, thanks for your help. We have solved the problem and the dishwasher is working! Thanks. ... LG LDF9810ST Built-in Dishwasher

I changed the handel and switch assembly on my dishwasher because the old one was broke.The dishwasher does not turn on. It still doesn't work. it doesnt even light up. although one button does glow a little. Do you have any idea what it could be? the model number is MDBH955AWB


Check for line voltage at the door switches and from there to the control board thats to the right of the door latch switches for line voltage,if you have line voltages in all these areas then replace the front membrane push button control panel that ... Maytag MDB9600A Jetclean II Built-in Dishwasher

Smeg df612sdx Until last week I enjoyed several years faultless service from my SMEG Stainless Steel dishwasher, with the exception of needing to replace 2 x spray arms. The unit has now stopped working altogether. Despite powering up several times, I continue to get both the start/pause and selection programs buttons constantly flash (green lights) when the unit is switched on; previously this only occurred once the wash cycle was complete. Any thoughts would be most appreciated. Thank you


... Dishwashers

We have a Maytag MDW700EDWG washing machine and it has stopped working. The display window is showing F2 and will not go to the time lenght of any program. I am unable to switch it off at the Start button. It is making a noise as if it is trying to do something - but then stops. I have cleaned the filters, checked water supply but still have F2 showing. Please can you shead any light or let me knoiw what to do Many thanks Emma


Is it the salt reservoir that is empty?\015\012Did you solve it already...mine has the exact same issue now ... Maytag Dishwashers

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Hoover hnd315 dishwasher program buttons not lit or working.


I have the same problem, did you manage to fix it, and if you did what was the problem? ... Dishwashers

Whirlpool "Quietflight II" - Will not start. The button for "Delay" works, and the button for "Cancel/Drain" works. Pressing this button will drain the unit. No other buttons will work, however, and the unit will not start. Ideas? I've taken the control panel off and looked at it's guts, as far as I can tell everything looked ok (not burnt and no loose wires), although I am no electrician....


Have you tried testing the control panel with an VOM meter? You can press a button and test the wiring that would go to that particular circuit. See if you get a reading on the specific wire when that particular wire is pushed. Does sound like a cont ... Dishwashers

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

The on off selector switch on my Blanco d/washer BFDW 670S no longer works unless I stand with my finger on the button at which point the light comes on and the dishwasher swings into action. Apparently I need a new selector switch at some considerable cost and delay (not in stock from my supplier). Any other suggestions? Once the light is on, everything works as normal but the button just won't stay depressed. Thanks, Jan


... Dishwashers

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

Whirlpool adp 7000 program button not working


... Dishwashers

Pdw 9200 jo3ww dishwasher- The start button doesn't work. The arrow keys work and the heated dry button works. I tried turning the power off for 30 seconds and it still doesn't work any ideas?


... GE PDW9200N Built-in Dishwasher

Have a Miele G1220SC dishwasher. It recently developed a strange problem: when switching it on ALL program lights come on and the machine starts taking water. after a while it stops taking water and starts to pump water, all the time all program indicators remain on. if you leave it on a while ( about 4 or 5 minutes) it is impossible to switch off the machine with the main switch, all you can do to stop it is unplug it. anyone experienced something like this and have any idea what part is malfun


Follow this steps and fix it. God bless you\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Miele Dishwashers

Used some washing up liquid instead of dishwasher tablets, after i got rid of all the bubbles and drained it, it no longer starts. If i switch the power off and leave it for a few minutes i can select a prgram it starts and a few seconds later there is a beep and the solid green run light on the program selectoe is flashing over the left hand program button. At this stage pushing any program button does nothing, i have to swith the power off and wait 5 miniutes and the the above patten is repeat


Dear sir vif you have used liquid soap in your dishwasher it will make mountains of bubles to kill all bubles outin a hurry take a sos pad put it in your machine and run the dishwaser this will remove all of the soao instantly try it it really works ... Ariston Technologies Dishwashers

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Model mdb7601awb diswasher . Nothing works , no buttons torn on or work when pushed, no action. 1.Have checked power to unit and is ok 2.checked door switches (2) and both work properly. 3. no visual discoloration on circuit board. There is a blue dot on the wiring harness from control board to button panel.When evaluating with magnifing glass I believe this to be blue ink droplet and not any burnning of harness. Need a Guru.


I have had the board replaced 5 times and the entire dishwasher replaced once. It was necessary to go to the state attorney general to get Maytag to extend the warranty. Just called the service center for the sixth time, after this the warranty will ... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1328 seconds