Having problems with your Dishwashers ?

Top arm does not turn in most of gibson amana an frigidaire this is done by ball in bottom of pump .it is clean.spray arm are clean .bottom arm move all the time.timer works it hesitates every so often and so ball will move an water should go up to upper arm but doesnt.common problem on these units but dont know how to cure?change ball.didnt work..on one unit changed pump cure problem for 4 months then returned....also does anyone know were u can buy the plastic they used to sell for dishwashers


Answers :

Can yo give me the make and model number sol I can look at the service manual for you?
Hello,
\015\012
\015\012besides the ball missing, you might not have enough water pressure to reach the top arm. Check the water level of the unit. Also, the holes in the spray arm could be clogged as well and the pump could be clogged, which also could decrease the pressure. You can stick a putty knife or something flat into the slot when it's in the wash cycle and watch to see if the upper spray arm sprays. The tops and bottom spray arms take turns to rotat. It's a good concept because it saves on water.
\015\012
\015\012Thanks
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Top arm does not turn in most of gibson amana an frigidaire this is done by ball in bottom of pump .it is clean.spray arm are clean .bottom arm move all the time.timer works it hesitates every so often and so ball will move an water should go up to upper arm but doesnt.common problem on these units but dont know how to cure?change ball.didnt work..on one unit changed pump cure problem for 4 months then returned....also does anyone know were u can buy the plastic they used to sell for dishwashers


Can yo give me the make and model number sol I can look at the service manual for you? ... Dishwashers

Water stopped pumping so ordered new pump. Upon removing the old I discovered it had a few straws twisted up into the pump. Removed and reinstalled pump and it sounds great and throws water all over with force. PROBLEM: Now there is ZERO water coming through top tube to spray arm. Pulled pump back off and noticed what seems to be a "white diverter ball" that moves a little in front of the inlet for the upper water tube. Any guidance to where the ball should be prior to installing the pump or i


... Kenmore 15529 Built-in Dishwasher

Water stopped pumping so ordered new pump. Upon removing the old I discovered it had a few straws twisted up into the pump. Removed and reinstalled pump and it sounds great and throws water all over with force. PROBLEM: Now there is ZERO water coming through top tube to spray arm. Pulled pump back off and noticed what seems to be a "white diverter ball" that moves a little in front of the inlet for the upper water tube. Any guidance to where the ball should be prior to installing the pump


... Kenmore 15529 Built-in Dishwasher

I have a frigidaire dishwasher - model number PLDB998AC1. There are two spray arms in this dishwasher - lower and upper. The lower works fine but the upper spray arms are not spinning. There is what I think adequate water pressure coming in from the top but no movement on the upper spray arm. Here is what I know: 1) The water pressure and spray arms alternate between top and bottom. 2) The upper spray arm moves freely when I push it gently. 3) I have removed the pump and cleaned out an


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Recently our GU1100XTLQ1 started having a problem. It barely cleans the bottom rack, and barely gets top rack wet. The soap stays stuck in the dispenser. I can't see inside as it runs, but my guess is that not enough water is being shot out of the various spinning arms. From looking at diagrams it would appear that this dishwasher uses a pump to circulate water from the bottom of the cavity through the spinning arms. Is my problem a dying pump?


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Upper & bottom arms are not turning even though the motor seems OK, pump for draining seems OK too. rcently I changed the pump kit plus some gasket and seals. My Maytag is about 14 yold and was very good for me untill I changed the parts. Could it be a weak motor pump. The water splashes very much in the machine but no arm turning!? Help me thank you Ben


Hi Ben, had the motor impellor shattered in the old pump ie-chunks broken off ? if so there is every possibility that these pieces have lodged in the wash delivery pipework at an elbow or indeed at the arm boss itself -i would try to check as much of ... Dishwashers

My kenmore 665 dishwasher will not pump water to the lower and upper spinner arms. The pump entry screen assy seems to have one tear in it and is dirty. However water does come out if I take off the lower arm assy. Is this a sign that the pump is bad and is not pumping enough water to move the arms or is there another problem?


The pump is probably defective (low pressure). Enough to spin the bottom but not the top. ... Kenmore Dishwashers

Kitchen Aid model KUDS01FLSS3, water gets pumped into bottom of dishwasher but when the cycle needs to change to shoot the water over the dishes nothing happens. When the cancel button is pushed all the water will drain.I have cleaned out the bottom drain compartment that was jammed with calcium build up and guck. Would this be a pump /motor problem or electrical circuit board problem?


... KitchenAid Dishwashers

Kitchen Aid model KUDS01FLSS3, water gets pumped into bottom of dishwasher but when the cycle needs to change to shoot the water over the dishes nothing happens. When the cancel button is pushed all the water will drain.I have cleaned out the bottom drain compartment that was jammed with calcium build up and guck. Would this be a pump /motor problem or electrical circuit board problem?


... KitchenAid Dishwashers

Water stopped pumping so ordered new pump. Upon removing the old I discovered it had a few straws twisted up into the pump. Removed and reinstalled pump and it sounds great and throws water all over with force.rnPROBLEM: Now there is ZERO water coming through top tube to spray arm. Pulled pump back off and noticed what seems to be a "white diverter ball" that moves a little in front of the inlet for the upper water tube. Any guidance to where the ball should be prior to installing the pump o


... Kenmore 24 in. 16193 Stainless Steel Built-in Dishwasher

Both spray arms of my DU943PWKQ0 do not turn or spray. The motor is moving and the it drains without problem. During the wash and rinse cycle I can hear the sound of water, however it doesn't clean at all and the sprays arms stay where they were. It seems the motor only creates no spray, but wave. I powered cycled the dishwasher, the problem remains the same. Anyone know what's wrong with it? Thanks James


Try rotating the spray arms by hand. It should rotate freely. If possible clean the arm rotating place by removing them.Arms rotate by by pump pressure only. finally check the water pump also. ... Whirlpool DU943PWK - Multiple Color Built-in Dishwasher

I have an LG ldf7811st dishwasher. My bottom arm spins with water, my middle arm does not spin but does have water coming out, and my top arm doesn't spin or have water. I have just finished taking apart the arms, the supply to the upper arms, the filters and the impeller. I cleaned everything and nothing really seemed clogged. I have tested it since and it still has the same problem. I know that they aren't spinning because i placed them in a certain position before i ran the test run. They


I'm thinking like you're thinking, that it's something affecting the water pressure, but you've done everything in the upper section, so the problem must be from below, unless you have a leak somewhere you haven't noticed and are losing pressure beca ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


... Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


Hi There,\015\012\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lev ... Dishwashers

Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers

My dishwasher runs but does not have enough pressure to clean the dishes or turn the spray arms. Arms spin freely. I have removed and cleaned the screens in the bottom of the dishwasher. I also have removed the large pump and checked it for damage..no problems found. Model SHU43CO5UC / 17


Hi.Below a list of things to check.Check the water inlet at the back, ensure that the hose is not clogged or kinked, and that there is sufficient pressure.Ensure that the machine is not underfilling. Test the water ... Bosch 24 in. SHU43 Built-in Dishwasher

Water pumps into the bottom of the dw but the spray arm doesn't rotate and spray. It also empties, so the problem seems to be with the spray arm. Any solutions?


Hi,When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher ... Asko 1385 Dishwasher

Top wash arm does NOT spin, but is not blocked or hard to move by hand. Does this run off water pressure? Whatshould Itry next. I have already removed the filters and cleraned around the pump. The bottom wash arm works great.


Remove the dishwasher from the cabinet and look at the hose going up to the top. Make sure it isn't clogged and that there is nothing in the port where it comes out of the pump. The top arm is powered by water pressure from the pump. ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Miele dishwasher G2870 scm. There is an F14 fault. I have cleaned the arms removed the waste basket from the bottom of the dishwasher and removed the two parts one with the large metal ball to expose the plastic wheel clog. There does not appear to be a blockage. I also removed the top arm and cleaned that out. I don't know what other inlets to check as the guide does not tell me exactly what an F14 fault is but explains F11,12,13. Can you help?


F14 on your model of dishwasher is indicating a blockage, poor water\015\012pressure or could be a fault with the pump pressure level switch or\015\012circulation pump.Filter and non return valve is cleaned of any blockages and if the fau ... Dishwashers

We have a LG direct drive dishwasher (LDF7932ST) that doesn't seem to clean very well. It leaves dried on food bits and a white film on everything especially the cups and mugs. Even on the power scrub cycle with an extra rinse. If the problem is the recirculating pump how do you remove the arm or bottom filter to clean out? I can't seem to locate the instruction book. Thanks for the help Tina


... Dishwashers

We are getting a grit on the dishes on the top rack. We have done many things to solve the problem. Running tang crystles, runing CLR through it, taking it apart to check for blockages, checking the impeller on the pump, blowing comprssed air through it, scrubbing the inside many times. The funny thing is it only happens about every third wash cycle or so. The upper spray arm is free with no obstruction. The dishes on the bottom rack are clean. We use Electosol and jet dry. Our water is softened


Hello John\015\012\015\012Thanks for all the detail. It's far more than I usually get to start with, but please could you also answer the following quick questions:\015\012\015\012- Are the particles hard and gritty or is it f ... Asko Dishwashers

Noisey maytag We have a maytag quiet series 300 with the 3 racks. Just recently we have been hearing alot of noise from our dishwasher while it is in the washing and rinsing mode. We have checked the arms to make sure they are moving but doesn't seem to be a problem. Thought maybe there is a liquid that we could pour into the washer to run through it's cycle? Of course we know nothing about the inter works of a dishwasher.


Hi, i had the same problem twice and both time there was some plastic stuff in the shredder. Remove the screw in the middle and remove the cap and you will probably find some pieces near the blades. ... Maytag 24 in. MDB5651A Built-in Dishwasher

We have a Bosch Model SKT5102GB/07 and the problem is as follows; we load the dirty washing and start the washing process, the machine then goes through the full cycle of wash. Once finished you open the door and notice that the washing is still dirty and a large pool of water is laying in the bottom of the machine. We have had an independent engineer look at the machine and he has advised that the pump needs changing. Look forward to your reply, thank you. Regards Michael Ballard.


Replacement parts are available here\015\012http://www.repairclinic.com/SmartSearch/SmartSearch.aspx\015\012\015\012on the narrow ... Bosch Dishwashers

Have Fisher-Paykel DD603 double-drawer dishwasher. Top drawer motor making loud noise. )Bottom drawer fine.) Still seems to wash and definitely pumps water but sounds like a "motor with a broken belt." Checked filter and rotating spray arm - no problems. (Found a little broken glass in filter; could be very old.) Suggestions?


If glass has gotten past the screen and into the pump, you may have a pcs. logged in the pump housing.\015\012Best way to correct this, is to remove the pump inlet and outlet lines and flush out with a water hose.\015\012Keep ... Dishwashers

Frigidaire dishwasher Water does not go through arms, bottom or top, at all (does not wash). You can hear motor running. Pump works fine; discharges water as normal and fills to proper level. Problem just started with no warning; no strange noises etc.


CHECK WATER INLET SOLENOID OR TIMER ... Frigidaire 24 in. PLD2850 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1585 seconds