Having problems with your Dishwashers ?

What does the error code LE mean on my LG Dishwasher Model LDS5811ST mean? Dishwasher makes noise in the rinse cycle and at end of cycle LE error code shows in window.


Answers :

MAin wash motor needs replacing
\015\012
\015\012Affordable Appliance Repair
\015\012Lake Forest, CA 92630
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What does the error code LE mean on my LG Dishwasher Model LDS5811ST mean? Dishwasher makes noise in the rinse cycle and at end of cycle LE error code shows in window.


MAin wash motor needs replacing\015\012\015\012Affordable Appliance Repair\015\012Lake Forest, CA 92630 ... Dishwashers

Error Code I just put my dishwasher for a cycle. It started making some weird noises during the rinse cycle and now it came up with a code LE. What does this mean??? Please help.


LE stands for a locked motor. If the motor has gone it has to be replaced. In some case though, depending on the age of your unit, it could be a broken wire in the door. If you remove your front panel (6 screws) you can have a look, but turn off t ... LG 24 in. LDS 5811 Built-in Dishwasher

Error f2e2 Have a new (March) Kenmore Elite dishwasher, error code F2E2 and after the initial rinse cycle it dumped all the water on the floor. What does this error mean?


... Kenmore Dishwashers

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

At 2 minutes left in the wash cycle, the quick rinse light starts blinking and the timer goes to 0. My dishwasher is a Whirlpool Quiet Partner IV gu1500xtkbo dishwasher. I'm assuming the blinking light is an error code. What does it mean?


... Whirlpool Dishwashers

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

I have a Kenwood Dishwasher KDW12ST3A. P1 cycle stops after about 40 minutes and shows on the screen an error code of 'E3', Not sure what this means as I have mislaid manual. Can you help please?


... Kenmore 15762 Dishwasher

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

I have the "rinse" error code on my kitchenaid double drawer dishwasher kudd01dppa1. I've turned off the power, then it worked for one load and the code reappeared on both drawers again. What should be a next step? it says in the manual that the "rinse" error code means that something happened to the flood switch...? Can this be fixed without calling out the kitchenaid technicians? thanks


... KitchenAid 23 in. KUDD01DPPA Stainless Steel Dishwasher

I have an IAG dishwasher that keeps stopping on cycles before the dishes are dry and coming up with error code E7 which asks me to rerun cycle and if code appears again contact maintenance. Any suggestions on what code E7 means


... Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

Error Code E1 means longer inlet time. possible causes faucet is not opened, or water intake is restricted, or water pressure is too low, according to the BRADA portable dishwasher model EP9242AWW What does that mean and how do I fix it? I have shut the water faucet off and the error message still shows.


... Dishwashers

My Teka Dishwasher DW7 80 FI does the first water intake operation, it sounds like rinsing, and the you hear the pump evacuating the water and two beeps as when it finishes the complete cycle. About 6 minutes. Then Stops. The lights that stayed on says error E8 according to the manual. I have done the suggested fix as ending the cycle manually and turning off and on the DW. I tested "many" times in various modes and the same preemptive end.


Hi.E8 is alternate washing system malfunction.The alternate washing system consists of a valve located in the underside of the appliance and connected to the impeller motor. The valve opens and closes switching spray on and of ... Dishwashers

Kenmore elite dishwasher runs until it is manually shut off by opening the door? My Kenmore Elite runs continuously until I manually drain (cancel) the cycle. Then I have to rewash with no soap to simulate the rinse and again manually drain (cancel) the cycle. This was a $650 dishwasher. I am not sure how to reset the controller or even trouble shoot for an error code. Any suggestions?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

When I start the top drawer it defaults to 5 minutes (with the lights Heavy, Fast, Rinse highlighted) runs for a couple minutes, then stops and the LED starts randomly cycling through all kinds of codes very quickly. There is water in the tub that has not drained after completing the couple minutes of operation. This cycle repeats itself if I hit the power button again after the LED starts freaking out. The 5 min cycle shows in the LED, sometimes with the no circulation error, sometimes with the


Here is the solution: \015\012http://applianceguru.com/forum1/24814.html ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

F4 error fisher & paykel nautilus dishwasher sometimes this error comes up and it seems to occur about 10 minutes from the end of the cycle. it doesn't happen all the time. the user guide does not specifically address this error code.


F4 is a heating error- dishwasher has not reached temperature in allocated time. If intermittent fault, problem is usually with electronic board, which has temperature sensor attached. Sometimes the wiring to the control board burns out and can give ... Fisher Dishwashers

Whirlpool Dishwasher ADG 9020 showes error code F6. What does that mean?


... Dishwashers

My lxi dishwasher drains more water than it fills during a cycle so after about three cycles the water level becomes to low. No error messages come up but I have to turn it off and refill it all the time. water pressure at the machine guages shows about 20psi when rinsing


There are two different styles of lxis one style has a drain diverter valve probably messed up some how something stuck in it not diverting the water to the wash arms and instead pumping right down the drain I am guessing this is your problem.There i ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

My frigidaire dishwasher PLD2855RFC0 intermittently either stops during the cycle or ends the cycle with the code PF flashing in the timer window along with the "High temp wash" and "No heat dry lights" flashing. What does this indicate and what is the fix?


... Frigidaire Dishwashers

I have a frigidaire dishwasher fdb520rhb2. Lately, at the end of the cycle the high temp wash and heat dry light will start blinking. The cycle does not finish. Cannot find the error codes in manual. Thanks.


... Frigidaire Dishwashers

Hi My AEG favorit dishwasher shows error code i50 by the end of a program. What does this code stand for ? Cheers Bent


... AEG 24 in. Favorit 40850 Free-standing Dishwasher

I have a Siemens SN25M230GB Dishwasher showing the following: Fault Code E15 Digital display showing (Error) E15 with a flashing 'tap' What does this mean? Is it something that I can fix myself or does it need to be looked at by a professional? Thanks Tina


... Siemens Dishwashers

My smeg d1612c dishwasher is stopping at the rinses cycle and not doing anything no fault code is showing. The dishwasher is heating up motor is rotating and pump is working. can anyone help


... Smeg DWD612C Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2638 seconds