Having problems with your Dishwashers ?

Display lights up but no sycles will begin

\015 Will not fill or retract water\015

Answers :

Sounds like cold water inlet valve is stuck as a dishwasher will not work unless it has water
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Display lights up but no sycles will begin


Sounds like cold water inlet valve is stuck as a dishwasher will not work unless it has water ... Dishwashers

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers

"sensor ok" - display is not lighting up at beginning of wash cycle - then "sanitation rinse" icon not displayed at end of cycle even though sanitize button was selected before start of cycle


... Bosch SHX98M09UC Integra 800 Series Dishwasher w/Display

My Miele G2430 dishwasher stops right after draining in the first minute or so after starting, and the intake and drain light comes on. The solenoid at the end of the intake hose then clicks and the light begins to flash. I applied suction to the intake hose to determine if the solenoid is working, and the valve does open and close. There has been no error code displayed. I cleaned all of the parts and filters referred to in the owner manual.


For a drainage fault heres what the miele service manual says for your machine\015\012Water present in appliance and is not being drained off. The display shows Drain fault F11. The buzzer is activated for 2 minutes. ... Miele Optima G2430SCi Stainless Steel Built-in Dishwasher

I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breaker to reset it but no c


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. It seems to be the ... Dishwashers

I have a Frigidaire Series PLD2855RFC3 dishwasher. Near the end of the cycle the dishwasher stops and begins flashing "PF" on the display and the lights for "Hi Temp. Wash" and "No Heat Dry" also flash. I know "PF" = Power Failure, but the power never goes out... so what is causing this error and disruption in the cycle?


... Dishwashers

By jleejr on Jul 20, 2010" " I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breake


HI. The actual culprit in this situation will be your control panel(Defective Touch-pad circuit board). The panel and touch pad assembly are integrated. They share the same space. There is a small ribbon cable on the rear of the control panel that li ... Maytag Dishwashers

We have a Bosch SHE44C02UC/46 that suddenly won't start. I pushed the on/off button to start the dishes cleaning on the 'Power Scrub Plus' cycle and the display lights up with a 125 min. indication for the cleaning time, but the dishwasher never starts. It just sits there completely silent and never begins the cleaning. The dishwasher has worked perfectly up to, and including, the last cleaning cycle (3 days ago) for the last 4 years. Suddenly, today, nothing. Zip. Zilch. Nada. I don't get i


Hi.Re:" I\\'m sure it has to be something simple." A: yes, probably a fault, simple as that.To start there is a recall concerning this model. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Countdown display is flashing saying 2:10 but dishwasher does not respond to pushing any of the buttons (light stays on Power Scrub and does not respond to selecting other wash cycles). On'Off button works but none of the other buttons responds. Machine does not begin washing when door is closed


... Bosch SHE6AP0 Builtin Dishwasher

I have a prima lpr600 fully integrated appliance. it appears to start - emptying machine to begin with, then starting to pump in water - but then starts to beep continuously! the display light flashes 11 times before a pause, but i cannot seem to find what this error code means. please help!


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Frigidaire Model Number GLD4355RFS1 Serial Number TH80493988 Dishwasher. It quit working when the Rinsing Agent Low light came on. We filled the rinding Agen dispenser with hopes that it would come back on. The Rinsing Agent Low light went off but the unit never came back to life. When the room is totally dark, you can just barely see the lights in the LED display and other lights. It will not come back on. I tied turing the power off and the "PH" alert is displayed in t


... Frigidaire Dishwashers

I have a Kitchenaid Dishwasher, model KUDM01TJWH0. It runs through the washing cycle properly, but then the Rinse Only light begins to flash and it does not drain. I have tried hitting the Cancel/Override button (also tried hitting all other buttons, but they were ignored too), but it also begins to flash with the Rinse Only light together. If I unplug it, wait a few moments, plug it in and all the lights are off when it comes back on, wait a few moments and hit Cancel/Override, it empties and s


... KitchenAid Dishwashers

I have a kenmore DW model 16019. The clean Light stays on the light does not turn off. I have tried to disconnect and have taken the motort apart to make sure everything is clean. What Can I do to solve this problem? 1. Does the washer work at all? No it does not work 2. Does it display any codes or flashing lights other than the CLEAN LIGHT being lit? no other lights are on except for the green blinking light 3. Is the light solid or blinking? blinking Green light 4. Entire model # is necessary


Thanks for re-posting with all the info!!The model # is 665.16019403The cleaning light blinking is a fault code listed in the tech. service sheet, its usually a faulty heating circuit.The sheet can be found behind the ki ... Kenmore Dishwashers

"Light Dry" light flashes 5 times & odd light displayed


Maytag website...all the help youll need ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

The dishwasher will not begin wash cycle. When I press the "start" button, the "heat dry" light illuminates and the "washing" light blinks, but nothing else begins.


Hi\015\012\015\012When these lights flash on your machine it is actually transmitting a code which can be read by a technician to help determine where the fault lies.\015\012\015\012However there may be a simple fix that you c ... Dishwashers

There was some ordinary dishwashing liquid leftover on plates when i placed into dishwaher and this caused foam. The machine had a spanner appear on display and blinking light with a beeping noise. whenever I turn the machine off from the power button, it would after a 1 minute turn itself on again. with the blinking light, beeping noise and spanner picture on display. 1. how do i turn off completely 2. what does spanner mean and how do i resolve.


Hello &\015\012Welcome to FixYa\015\012\015\012Spanner\015\012indicates that there is excessive water in the unit, and instead of leaving it\015\012open you can take off the bottom front panel of the unit and clean the ... Dishwashers

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

Have a 665-16293201 dishwasher with electronic controls and smart sensor. Approx 10 years old in great shape. it just started having a problem - it takes a long time for the sensing to be completed at the start of a wash and then the washer will start and display a time - like 92 minutes - turn the sensing light off, then start to wash and count down. when it gets to 86 minutes, it starts to sense again and will continue washing while displaying 86 and with the sensing light on. It will keep


... Kenmore 24 in. 16293 Built-in Dishwasher

My Delonghi dw67s power button is on but the display panel wont light up. Sometimes when I leave it on an hour or so later the display comes on but I have left it for several hours and it still isnt lighting up??? Help Please!!!


Not true..... ... Dishwashers

I have a KitchenAid KUDS01IJ Dishwasher. The Rinse Only light is blinking and cannot be turned off or switched to another setting. Multiple presses of the Cancel/Drain button will sometimes have the display show '2' or '---'. A few minutes later the display goes blank and the Rinse Only light starts to blink.


... KitchenAid KUDS01IJ - Multiple Color Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

My Maytag dishwasher model MDB600AWB, serial 18721619CN Quiet Series 300 will light up on the panel except for NORMAL WASH and START. It will not run. All other buttons work. It displayed the number 9 and the RINSE ONLY light came on after we got off the phone with Maytag. Initially nothing would light at all. We changed the fuse (it is NOT on a breaker) and it again didn't light. A few minutes later it did light the above mentioned buttons.


... Maytag Dishwashers

Touchpad--No Response The touch pad and Countdown timer display will NOT respond except when the Rinse Only pad is pressed. The Countdown timer displays "9" when this pad is pressed. As expected the light and display turn off after 30s. If after 30s or longer the Start/Cancel pad is pressed with the dishwasher door closed, then the Countdown timer displays "2H" and the dishwasher runs through the ?Auto Clean? or ?Heavy Wash? cycle. Not sure which since neither pad is lit. Is the problem the


The "2H" is an error code indicating the control panel needs to be replaced. ... Bosch 24 in. SHU53 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0936 seconds