Having problems with your Dishwashers ?

E1 error code on my kenwood dishwasher [kwd243a


Answers :

Hi
\015\012The E1error code indicates a water inlet error.
To access test mode: press and hold Normal+Eco, and press Power. Release buttons. Then press Start(display n:01).Press Start again (display shows water level frequency-not important). Press Start again-(display n:03-motor will be running). Press Start again (display n:04-drain pump will run). Press Start again (display n:05-inlet valve will come on and machine should fill with water). You have now tested major components are working-if you keep pressing start you will scroll thru and test other functions, like heater, dispensor etc, but not needed for your fault.
If Machine didn't fill with water in test mode, you probably have a faulty inlet valve (test resistence should be approx 3.7-4 k ohm).
If inlet valve has tested OK ie machine filled with water in test mode then:
Disconnect from power.
Remove side panels (need to remove top, and bottom front panel to then be able to remove sides)
- Check no water in base of machine-water in base will indicate machine has leaked and activated the safety device which shuts off inlet valve.
- If OK, you probably have a faulty flow meter(measures water intake). Located left hand side of machine, large plastic compartment, which has a sensor at the bottom with 3 wires (red,white,black) that go up to control board. Replace entire flow meter assy-relatively inexpensive part.
- If you still have problem, then control board is faulty, it is much more likely to be flow meter .
\015\012.
\015\012Thanks for contacting fixya.com
I had this same problem. Would start to run a cycle, then come up E1 with all the water in the bottom. The problem for me was that a small chip from a cup had lodged itself in the drain pump. this was preventing the dirty water to be pumped away to the drain unless it was gravity fed. Because the dishwasher doesnt fill with any more water until it has got rid of the old to prevent flooding, it was coming up with code E1. It wasnt too hard to sort, just removed a few panels and took the pump out to give it a clean. Hope this helps some of you.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

E1 error code on my kenwood dishwasher [kwd243a


Hi\015\012The E1error code indicates a water inlet error. To access test mode: press and hold Normal+Eco, and press Power. Release buttons. Then press Start(display n:01).Press Start again (display shows water level frequency-not importan ... Dishwashers

We have a Kenwood KDW8ST2A dishwasher. We used to get the error code E3 (when still under warranty) and were told not to use dishwasher tablets as it generated too much foam. The problem has been intermittent but now we get the E3 error every time, no matter what program we run, or how little detergent we put in. I've a feeling its not heating up properly, is there any way to check the heating element? Is it worth attempting a repair?


... Kenwood KDW243A Builtin Dishwasher

Kenwood dishwasher error code e8 - Kenwood Dishwashers


... Kenwood Dishwashers

Dishwasher kenwood kdw243a error code 3 - Kenwood KDW243A Builtin Dishwasher


... Kenwood KDW243A Builtin Dishwasher

We have a Kenwood KDW8ST2A Dishwasher which is about a month old. The other day we had to pull it out from under the worktop because something rolled under it. When we put it back and went to use it later that day, we got an E1 error code appear and it's been like that since. We pulled it back out to make sure that we hadn't accidently pulled or loosened any of the pipes. We have the manual which does tell us what the error means but it doesn't tell us how to fix it. I'm sure it must be somethin


You can find a manual here ... Dishwashers

E4 error code on my kenwood dishwasher kid60510


... Dishwashers

E1 error code on my kenwood dishwasher KDW60X10


... Dishwashers

Kenwood dishwasher kid60s10 error code 3.4


See your instruction manual, go to the section troubleshooting and see th error code and proceed.if you do not have go and download www.retrevo.comGod bless you ... Dishwashers

Error code e4 on kenwood kdw12st3a dishwasher too much inlet wate


HI there,I have had the same problem as most of you. I seem to have fixed it by 1. Bail out all the water from the inside2. Remove the filter and 2 x mesh pieces.3. Continue to bail out the water from the filter well. ... Kenmore Dishwashers

Hi I was wondering if you could help me with a problem I have with my kenwood kdw234a dishwasher, it is displaying the error code E3. This occurs about half way through a wash cycle. Thanks James


... Kenwood Dishwashers

KENWOOD IP21 EI error code - Dishwashers


Not washing properly and E3 keeps coming up thank you if you can help x ... Dishwashers

How do I deal with an E3 error code? - Kenwood Dishwashers


E3 error code means the water is not being heated to the required temperature in the machine.This may be either a defective heating element or faulty thermostat. ... Kenwood Dishwashers

I have a kenwood dishwasher (kdw 243a) and it is displaying error code e4. google tells me it is to do with the overflow but It is integrated and I don't know how to remove it


Just pull the machine out and tip it on its side the water will pour onto the floor but just mop it up and it works ... Dishwashers

Hello, I am having problems witha kenwood dishwasher, it just isn't cleaning anything. It seems to be going through the cycles and sometimes the dishes particularly in the top rack are a bit cleaner but in general they are uncleaned. There are no error codes. I wondered if the arms for some reason weren't turning correctly as some of the dishes were clean but this is inconsistent. I have tried changing detergents, adding more salt and rinse aid but it still isn't working, can you help?


... Kenwood Dishwashers

I HAVE A KENWOOD KDW12ST3A DISHWASHER AND IT HAS THE E4 ERROR CODE THEY DID NOT GIVE ME A MANUAL WITH IT CAN YOU HELP


I hav a kenwood kdw12st3a and the e4 code came up and it said in the manual it had overfilled but it did'nt tell you how too fix it can you help ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Kenwood kid60b10 dishwasher has water in bottom, showing error code E1


... Kenwood Dishwashers

Kenwood dishwasher kdw12st3a error code e3, what does this mean ?


In the manual I have for this machine model E3 means: Longer heating time but not reaching requied temperature. The possible causes: malfunction of temperature sensor or of heating element ... Dishwashers

I have a Kenwood Dishwasher KDW12ST3A. P1 cycle stops after about 40 minutes and shows on the screen an error code of 'E3', Not sure what this means as I have mislaid manual. Can you help please?


... Kenmore 15762 Dishwasher

Code f5 error f5 to dishwasher kenwood


... Kenwood Dishwashers

Kenwood kid60b10 dishwasher has water in bottom, showing error code E1


... Dishwashers

I had a black out and the dishwasher was running at the time. The dishwasher emptied out all over the floor. when the power came back on the dishwasher was flashing an error code 4. I rang Whirlpool for assistance and they said it was over full but it was totally empty. We turned the dishwasher off at the wall hoping it would reset but it is still saying error code 4. Can you suggest something else we can do?


The trouble looks to be little confusing. Whenever the power failsduring mid cycle this happens. Try running the balance cycle. Since you say the water is fully drained, try adding water manually tothe wash chamber to certain ... Whirlpool Dishwashers

I have a Bosch SHU5316UC dishwasher. The last two times it ran, my wife says the display said "CL" (for clean) after running through the cycle, but she heard a "motor running" until she opened the dishwasher. Attempting to run the dishwasher tonight, it won't start - it displays a "P" (error code?) when you attempt to start it. Can you tell me what the error code P is? Thanks, Dave


P stands for program in computer algorthms. The device displays program whenver chages were made to the default settings. A powered on devices least has malfunction only requires reseting to attaon default features. Depending on the type of device, r ... Bosch SHU5316UC Dishwasher

Neff dishwasher error code e22neff dishwasher error code e22


... Neff 24 in. S5453X1 Built-in Dishwasher

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

AEG OKO_FAVORIT 6281i dishwasher - error code 20 (Siphon blocked). Out of the blue after 6 years of reliable once-a-day family use, my AEG OKO_FAVORIT 6281i dishwasher started OK but about 3 minutes into the cycle began flashing error code 20. At which point there was a litre or two of cloudy water sitting at the bottom of the machine. Since then I've tried redirecting the drain hose into a bucket, after disconnecting it from the kitchen drain. Same symptom, and no outflow except what was al


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1340 seconds