Having problems with your Dishwashers ?

All aspects of the dishwasher work except the wash motor/pump does not run. Is it the motor? I have taken the lower arm assembly apart and removed the support to spin the impeller. It spins fine although there is axial play.


Answers :

If the shaft is moveing from side to side you need to replace the motor. did you tern the impeller around about 3 complet terns?
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

All aspects of the dishwasher work except the wash motor/pump does not run. Is it the motor? I have taken the lower arm assembly apart and removed the support to spin the impeller. It spins fine although there is axial play.


If the shaft is moveing from side to side you need to replace the motor. did you tern the impeller around about 3 complet terns? ... Dishwashers

DWU9200AAX - not cleaning well and smells. Need to remove impeller assembly to finish cleaning out


... Maytag DWU9962 Dishwasher

I get the LE error code. I have taken it apart but the thing that spins was stuck but it still does not turn smoothly. When I try to unscrew the white spinning part it spins with it.Any suggestions on how to control the spin to remove and clean under the part.


The service manual at \015\012http://136.166.4.200/contents/Dishwasher/LDS5811/LDS5811_Service_Manual.pdf\015\012wil ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

I have an LG ldf7811st dishwasher. My bottom arm spins with water, my middle arm does not spin but does have water coming out, and my top arm doesn't spin or have water. I have just finished taking apart the arms, the supply to the upper arms, the filters and the impeller. I cleaned everything and nothing really seemed clogged. I have tested it since and it still has the same problem. I know that they aren't spinning because i placed them in a certain position before i ran the test run. They


I'm thinking like you're thinking, that it's something affecting the water pressure, but you've done everything in the upper section, so the problem must be from below, unless you have a leak somewhere you haven't noticed and are losing pressure beca ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

I want to inspect filter on Whirlpool DU1055XTSS2, but can't seem to remove the lower wash arm assembly. The top of the lower spray arm hub just spins and spins.


... Dishwashers

Broken glass stopped machine want to take apart and remove pieces. I think spinning arm can be removed, but don't know how


The problem is in the pump not the arms. must take the top of the pump off to cleen out the glass. if you try to run it without getting the glass out it will distroy the pump blades and it will need to be replaced. ... Whirlpool DU912 Dishwasher

I have a Kitchen aid tall tub dishwasher model #KUDCO3IVWH Yesterday the top rack didn't clean, today both racks stayed dirty - took apart the food chopper assemble and notice that there is water in the well is it ok to remove the food chopper blade? what else could be wrong


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers…Dishwasher Problems The ... Kenmore 16372 / 16374 / 16379 Built-in Dishwasher

My GE Profile Performance dishwasher (GSD 4910) doesn't drain. I hear the pump working, and water draining into the sink (not a disposal) as it should, but water is left standing in the tub about as high as the heating element. I have taken it apart and removed a few small items stuck in the system in various places, but that didn't affect anything. I have read here and there about the piston and nut assembly, but I don't think my model has that -- or maybe it does? Can you affer a


... GE 24 in. GSD4910X Built-in Dishwasher

Machine stopped before end of cycle and did not drain. Cleaned out water, took apart pump assembly, impeller, etc. and drain hose. No obvious problem. Put everything back but dishwasher won't star


... Whirlpool 24 in. DU920QWD Built-in Dishwasher

My GE Profile dishwasher is not cleaning the glasses on the top rack. It leaves all kind of grit and food on the glasses. I did some testing and it lookslike the wash rinse/wash assemblies are not spinning at all. I think the conduit main may be blocked or leaking at the seal. My question is, how do you remove the track (conduit) that brings the water to the upper rinse arms?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Dishwashers

My dishwasher impeller failed----just was loose in the drawer. i ordered part 525884P, motor rotor assy which has arrived from new zealand. but, there were no instructions on how to remove previous assembly and install the new. are instructions available? steve nute


First fold the racks on the side of the drawer up out of the wayThen Remove the cutlery basketThen with the drawer fully open grab the main rack from the front and pull upward, You will need to persuade it past the rinse aid d ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I'm trying to take apart a kitchenaid dishwasher door model KUDP01ILWH0 to replace the dispenser assembly. I removed all the torx screws holding the outer and inner door panels together, but they don't want to separate. Anyone know what the trick is here? Thanks


You can get assembly diagrams of your system. Go to;\015\012http://www.appliancepartspros.com/partsearch/model.aspx?model_id=503 ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Water standing in tub,already removed cleaned screens,also drain hose is not plugged,can feel spindle spinning on pump out motor.Would impeller be shot??....thanks


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Kenmore 17252 Free-standing Dishwasher

Sears kenmore dishwasher; model: 665.13763K600 (made by Whirlpool). Dishes have debris after washing in all cycles. Arms spin, water is running, dishwasher drains, and I removed the sump assembly to clean the chopper inlet. How do I diagnose it. I put it into diagnostics cycle and am unable to identify the issue.


... Kenmore 24 in. 16012 Built-in Dishwasher

Machine just started leaving dirty water in bottom of machine. cleaned filters,had machine apart,removed and cleaned waste pipe. pump runs and impeller feels ok.only time i could get any water to drain into bucket was when shook waste pipe very hard?


Check that the pump is clean and not loose. Make sure pump, impeller, and waste pipe are in alignment with each other and are clean. If it works when you shake the pipe, then there is still a clog inside or the pipes aren't aligned correctly and some ... Dishwashers

Broken Glass in Kenmore 15685 & can't remove Wash Impeller Screw


Same problem here! Great! ... Dishwashers

Impeller is spinning counter clockwise on the wash motor.


... Maytag 24 in. MDBH950AWS Built-in Dishwasher

How do I remove the latch assembly to bosch dishwasher model she44co5uc/22, in order to replace it?


... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

NEED TO DISASSEMBLE THE LOWER PUMP ASSEMBLY YO REPLACE LOWER IMPELLER.


... Maytag 24 in. DWU7402 Built-in Dishwasher

JENN-AIR Model number JD3B10AWX. Bottom of dishwasher is dirty, I want to clean it. I have removed six screws holding plate down, but cannot find any way to remove spinning blade. I think there's a filter underneath that I can clean or replace. Questions: 1. How to remove spinning blade? 2. Am I going about this correctly. Thank you


We have been having issues with our model where there is dirty sand deposited inside of glasses and dishes.You need a torque wrench for a triple square torque screw ... Jenn-Air Dishwashers

How do you remove the lower spray arm on a Kenmore Ultra Wash (665.17019.402)? I was told to hold on to the plastic screw and spin the arm counterclockwise to remove, but I've been spinning and spinning, at leat 100 rotations, and it is not coming off. I've uploaded pics so you can see the apparatus. http://picasaweb.google.com/gregoryor/Dishwasher?feat=directlink


Hi, In the center of the spray arm is a threaded piece of plastic/bolt.\015\012Use pliers and turn that tab on the bolt. If it doesn't turn easy. Holt the bolt and try to turn the spray arm with you hand.\015\012It will release the spray ... Dishwashers

Have a dd603 with an issue...took off the arm and the metal silver disk (the ones with holes) to get to the wash impeller-(the thing with blue blades) the wash impeller will not spin-which I think is part of my problem, since i looked at the lower drawer and was able to spin the blue blades easily...was also able to pull it right out. Cant pull out the upper wash impeller!!!! Really want to get this fixed before my husband gets home and I get the lecture about how I purchased a cool looking d


Lol I don't know a lot about dishwashers, just do him good and tell him afterwards, and then hire a mechanic to look at it.Why would you want to pull the propellers off anyway? The top one doesn't pull off because it's screwed on, and the botto ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

F2 code. Followed listed guidance of removing assmebly and checking...unfortunately, however, my impellar has separated from the rotor assembly and the rotor assembly is stuck in the drawer. I tried to pull up on the shaft with some pliers, but that didn't work and I didn't want to pull too hard and cause damage. Please advise as to how to remove the broken rotor assembly from the drawer. Thanks


There are no wires underneath the rotor - it is just suspended in the cavity. So you cannot do any damage except make scratches around that area. Maybe take a straightened wire coat hanger and insert from the side hole in the filter sump area. You mi ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Hobart model # C44 old dishwasher, wash pump motor will not remove impeller will not clear the hole, how to remove the impeller?


... Dishwashers

Wash Arms not spinning --Dishes not clean


Without the model number of your Maytag number, I can not determine if when you order a wash pump motor you also get the impeller.\015\012\015\012Sounds like you are on the right path to getting your dishwasher to wash dishes again. \015\012 ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0832 seconds