Having problems with your Dishwashers ?

Setting the water hardness system on Beko DWD 4310W. The handbook instructions seem to be wrong. There's no display panel on the machine as it states, and it tells you to press and hold Start/Stop button and switch the On/Off button, release the On/Off button, press and hold Start/Stop button for 10 seconds,( which you are still pressing anyway!) Then it says the last setting will be displayed on the panel for five seconds. But no panel.Totally confusing.


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Setting the water hardness system on Beko DWD 4310W. The handbook instructions seem to be wrong. There's no display panel on the machine as it states, and it tells you to press and hold Start/Stop button and switch the On/Off button, release the On/Off button, press and hold Start/Stop button for 10 seconds,( which you are still pressing anyway!) Then it says the last setting will be displayed on the panel for five seconds. But no panel.Totally confusing.


... Dishwashers

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

The contol lock LED is illuminated on the front panel of my Maytag dishwasher. (Neither my wife nor I pressed the control lock for 3 seconds!) We've tried to extinguish it by pressing it for 3 to 5 seconds, but it remains ON. We've turned off the breaker to the dishwasher overnight, but when we turn the breaker back On, the contol lock LED comes on. We simply can't unlock the control panel. We can tell that all of the other buttons work just fine because pressing any of them causes the 3 Sec LED


If by pressing the control lock button for 3 seconds does not solves the problem.then there are 3 possibilities due to which this problem may occur\015\0121)the door is not closing properly. the dishwasher door latch is either cracked internally or t ... Maytag Dishwashers

I have a MDB6759AWS3 that is one year and two months old. This morning I went to the control panel to press the buttons and some would light up and others would not. I disassembled the inner panel and looked at the "computer like" flat ribbon that connects the control panel to the main circuit board and noticed that some of the wires in the flat ribbon had deteriorated. I put it back together and pressed the buttons and they flash very dimly for a few seconds and got the dishwasher working bu


You may want to check the warranty iif it is a maytag or whirlpool, some have a 5 year warranty on the control and board. If not you can go to www.searspartsdirect.com to l ... Dishwashers

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

Pushing settings and start button but will not start. The green light comes on for the setting and the Heat Dry but once start is pressed it will not start and after 30 seconds the lights go off. Also, Smart Wash button no longer works


... Kenmore 13743 Staimless Steel Built-in Dishwasher

Maytag quiet series 200 model MD88750AWB Dishwasher doesn't work. Control panel only responds to the heavy wash button. When pressed it lights up along with three option lights. After about 10 seconds they go off. There is no mechanical response to the pushed button. There were no symptoms leading up to this problem. If you can give me a "head's up" about what to look for before I open up the control panel I would appreciate it. Thank You John


Hi\015\012\015\012\015\012\015\012\015\012\015\012If your dishwasher doesn't work at all, check these:\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is there power getting to the dishwasher? This can be difficu ... Dishwashers

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

Control panel is locked. no buttons work when pushed. door panel says to push and hold ''heat dry'' button for 4 seconds to clear. nothing happens. this is on kenmore ultra wash dishwasher


Try unplugging the machine and wait 5 minutes. Plug it back in, the problem should clear. ... Dishwashers

No Water Coming Into SHU43C05UC/12 Bosch Dishwasher: We have a Bosch Dishwasher, model number SHU43C05UC/12. It has been working for more than 4 years, but yesterday I notice that although I hear a motor sound, there is no water in the dishwasher. The LED display on the panel seems to be working all right. I ran a diagnostic pressing and holding Power Scrub and regular wash button then pressing the on/off button. Got C1 at start then P0 and the Regular wash and Quick wash flashing on/off. How c


... Dishwashers

I have a GE Quiet Power 3 that has completly died. I cannot get a light to come on or anything to beep when pressing buttons. I checked the circuit breaker and outlet and they are both working fine. I tried pressing and holding the reset button on the front control panel and nothing. It seems to have just died at 2 years old. Anyone have a solution? GE wants $80 just to look at it.


A dead set simply means a cut off of power supply. Open the back cover of your dishwasher . Locate the area where the AC cord is located and look for the plastic fuse holder which is usually installed in one of the AC cord line open it and replace t ... Dishwashers

We have a Beko DWD5410W dishwasher that has worked fine...until today - the 'wash' light is on but it is not wasing. I have pressed in the 'start' button and held for 5 seconds to reset and it then springs to life draining out or whatever that noise is, and then if I turn the dial to a setting (even the cold prewash) and press 'start' again it starts whirring away, then after about 10 seconds just stops, with the 'wash' light staying on. Not blocked, I have checked - this likely to be a frozen p


... Dishwashers

Dacor MDV24 dishwasher. I press cancel to turn it off and it works but after approx 10 seconds the start and normal button comes back on and beeps. I tried shutting the breaker and holding the cancel button for a long time but it still always comes back on. Got any suggestions?Motherboard or faulty buttons?


Hello &\015\012Welcome to FixYa\015\012\015\012If you have\015\012also checked the door lock-latch assembly and that is fine then yes it is the\015\012control board that is bad and needs replacement. Please get back to ... Dacor Millenia MDV24 Built-in Dishwasher

Further to my open question for my Asko N516 D5131 SS dishwasher I have been able to successfully press the wash setting cycle, which was before frozen on 'rinse and hold' . I then press the on/off. Button the time shows but as soon as I press it to start the dishwasher the screen changes to three horizontal curly lines and nothing further happens... It won't start. Please , I do hope somebody can give me advise. I cannot get to the power plug as it appears pot be located behind the unit whi


... Dishwashers

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

My Asko D1996 Dishwasher will not start. The control panel has 3 lights staying on - position #1, 6 and 7 and are unresponsive no matter what buttons are pushed - even after turning the power off at the breaker, the outlet and the on/off button.I've tried holding down the start button for several seconds to reset but this did not work. I have also cleared the drain, filters and removed any water and pushed and held the Start button to reset.


... Asko Dishwashers

Kenmore Ultra Wash Model 665 - 158* Front panel not working properly. Pressing Normal does not light that option. The only option that lights is "Quick Rinse", pressing this lights that option and also the "No Heat Dry" light. After a few seconds the lock light comes on. Looks to me that the "No Dry Heat" button is stuck on, which causes all the other things to happen Is there a way to fix this?


... Dishwashers

I purchased a second hand Electrolux Dishlex DX403 with a kitchen. The dishwasher turns on when I turn the powerpoint on and makes a noise as if it is about to start. I attempt to press the buttons to set a mode and start it and it wont work, the buttons dont do anything. How can I fix this?


... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Whirlpool dishwasher model GU1500XTLSO Control panel is mostly not responsive. Can enter "control lock" mode by pressing and holding "air dry". If I press air dry again in this mode, the green button flashes three times. Does this mean anything? I would really appreciate some help.


... Whirlpool Dishwashers

I have a built-in Kenmore UltraWash ~ Model 665.15819990. The problems we are experiencing is lately when we press "Normal Wash", the "Lock On" will flash on and off, and then "No Heat Dry" comes on & off and nothing works. We have tried pressing and holding the "No Heat Dry" button for 5 seconds and sometimes this clears everything. However, more recently, nothing is working. Suggestions?


... Dishwashers

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. Thanks


... Whirlpool 24 in. GU3600XTRY Stainless Steel Built-in Dishwasher

Kenmore Elite Dishwasher- The touchpad (control panel) keeps going ot and stops functioning. The control board is fine but the start button on the touchpad stops working. If I press it multiple times over and over it will finally engage and kick on. This is my second control panel, can the switch membranes be cleaned somehow?


Jodahabo,\015\012\015\012can you post the rest sequence? i would love to try this!\015\012\015\012thanks,\015\012\015\012the_strum_one ... Dishwashers

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

Dishwasher HED6612 - salt light came on - have now filled the salt up and light has gone off. since this has happened whatever programme I set it to once the pre-rinse has finished and the wash light comes on an alarm sounds and doesn;t finish the cycle. when the alarm sounded I have pressed the start/reset button for 10 seconds to see if it resets it. I requested a manual last week and not received a reply from yourselves. this machine is around a year old [no manual available] and has been


... Hoover HD95M Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1108 seconds