Having problems with your Dishwashers ?

Product-AEG.OKO,FAVORIT Dishwasher Hi, Our Dishwasher seems to have frozen mid cycle and no water is coming in when it is restarted. Is there a way of resetting it ?.I seem to remember this happening befor on a previous dishwasher and the engineer pushed a screwdriver into a dummy screw hole to reset it? Can you help Regards, Tim Appleton


Answers :

Press and hold the start/stop button for 5 seconds, this should reset your machine...
\015\012
\015\012If not you could see a small hole written reset on it,Pierce this button using a small PIN to reset
\015\012
\015\012RNJ VINOD KUMAR
Hi,
\015\012Try using a pin to poke the tiny holes in the arms that spin round. if they get blocked it will cause it to stop mid cycle,
\015\012OR
\015\012This problem is often caused by poor drain pump action between cycles. If the pump has completely removed all water from one cycle and the next cycle adds more water then the dishwasher "floods" and triggers the overflow protection. I have found that 9 times out of 10 the problem is with build up or blockage where the drain pump connects to the sink drain. Keep this clean and your problem should disappear. The drain pump could be faulty but stick with the simple stuff first. Occasionally the drain hose may fall off the back of the machine loosing its loop and thus creating poor pumping action and the machine freezes.
\015\012Unscrew the kickplate and the metal cover to access the bottom of the machine where the pumps and motors reside. Use a sponge to slop up the water in the pan. Blow dry the bottom. The machine will reset itself as soon as the water is gone.
\015\012OR
\015\012If you have been using liquid or gel tab detergents for a period of time, there may be a simple solution to getting the machine to run normal cycle times. Give the dishwasher a 'vinegar bath', by simply pouring 2 cups of distilled white vinegar into a bowl and placing the bowl face-up in the lower rack (do not add detergent, do not put other dishes in). Then just run a regular wash cycle and allow the vinegar to 'wash' through the system. This will clear the sensors of any filmy residue build up and allow it to start clearly reading the status of the wash again.
\015\012
Thanks for contacting fixya.com
Have a nice day.
\015\012GodBlessU
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Product-AEG.OKO,FAVORIT Dishwasher Hi, Our Dishwasher seems to have frozen mid cycle and no water is coming in when it is restarted. Is there a way of resetting it ?.I seem to remember this happening befor on a previous dishwasher and the engineer pushed a screwdriver into a dummy screw hole to reset it? Can you help Regards, Tim Appleton


Press and hold the start/stop button for 5 seconds, this should reset your machine...\015\012\015\012If not you could see a small hole written reset on it,Pierce this button using a small PIN to reset\015\012\015\012RNJ VINOD ... Dishwashers

Dishwasher (Model # SHU6806UC), unit is about 8 years old, very light use, less than once a month, and no previous problems. Turned on unit and after about 10 minutes, I found water on floor coming from dishwasher. Turned unit off and turned off water shut-off valve. Removed dishwasher from cabinet. Found mice had chewed a hole in water discharge hose under unit, inspected all hoses, and found another hole chewed in the 13" flex hose in the front of the unit. Also found the float chewed to alm


Hi,\015\012 Check the valve is open where the supply gets its water from the sink supply.There is a garden hose type swivel adapter after the valve, Close the valve tightly and then unscrew that hose coupling and see if the hose is full of w ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

I bought a house with a Bosch dishwasher in it and soon found that the top spinner holes are blocked with bits of old labels. I have removed the spinner and separated the concentric tubes but I do not see how to push the debris back along to the inlet. Do I need a power but very small jet to put into the holes along the arm? Would drying it then putting the suction of a vacuum over the inlet hole be useful?


This is very common if the filters are not cleaned regulary if you remove the arms and soak them in hot soapy water for around half an hour this should loosen the debris also tap them on the side of the sink this will remove more stubborn debris ,ref ... Bosch Dishwashers

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

Dishwasher leaking Our dishwasher all of a sudden started leaking. I've taken the front panel off the door and can see exactly where. It's not a hole or anything...it's at the front, left edge of the basin, the bottom left corner at the front. It seems that right after it fills with water, it starts to leak once water is moving around inside and washing cycle starts. It is as if big waves are being pushed to the front left corner and over the lip of the basin. I don't think the water level is to


Just an idea...if i'm understanding you correctly,could the door seal be creased there or folded over by use and age to permit this to happen? cause you said nothing is missing ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Kenmore Model 665.15955792 dishwasher. Water is leaking out the bottom of the door. I changed the door seal and the defusers but it continued. I took off the front of the door and I see the water filling into the base of the machine. When the dishwasher starts the cleam cycle, water is pushed up into the small square holes in the bottom of the door and then splashes up over the lip of the door and out onto the floor. It has never done this before, just started recently. I have had the d


... Kenmore Dishwashers

Samsung dms 301trs dishwasher with e 3 error ? Tried to unblock but no blockages and the pump only works when it wants to and can be started by pushing with screwdriver. Does the pump need replacing


... Samsung Dishwashers

I have a Bosch SHX98M dishwasher and the top arm will not rotate. I can see water coming out of the holes when open during a cycle and I have made sure there are no obstruction for the arm or anything stuck in the arm feed line. I just had a technician here who was at a loss and did not think the pump was bad since alot of water is being pushed around inside. The bottom arm works fine.


... Dishwashers

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

Kenmore Elite Dishwasher, Model 665.15979992 No Heat Dry Button/Light: The dishwasher will not work. Have tried to no avail the various alternatives listed in this thread and others. Here's what the dishwasher is doing: To start off, the red light on the "No Heat/Dry" button is on - sometimes it's on steady; other times it blinks depending on whether other buttons have been pushed. Pushing any other button also causes the "Lock On" red light to come on. Pushing the "Cancel" button causes all


Have you checked the thermal cutoff switch located inside the door by doing a continuity test to it if this is sounding like where your problem are is coming from on this diagram ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Maytag Quiet Series Dishwasher although it is not stainless steel, it is white. My dishwasher, shuts, and the lights come on when I push it but it will not start! Yesterday after a few attempts pushing cancel and so on, I smelled a STRONG concentrated smell of the liquid dishwashing detergent inside the dishwasher, but it never came on. Can you help, I cannot find the manual for this appliance, it came withour home when we purchased it in 2006, and it was brand new.


Here is the manual.\015\012\015\012http://shared.whirlpoolcorp.com/assets/pdfs/literature/Use%20and%20Ca ... Maytag 24 in. MDB5601AWS Stainless Steel Built-in Dishwasher

I have an older Bosch dishwasher I just hooked up in my condo. WHen a cycle is done there is no water is located at the bottom of the inside of the dishwasher, yet 2 days later water will drip on the floor (with the dishwasher door closed) and I'll open the dishwasher door and therewill be 2" of water at the bottom. The flexible water discharge hole located in the sink base is located at the top of the base cabinet, and the hose runs completly 100% downward from that hole to the garbage disposa


When you empty you sink, some of the water is going down the drain hose of the dishwasher. take the drain hose up as far as possible in a swan neck ... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

My LG dishwasher -LDF7810st has been a huge problem from the beginning. However I will just focus on the current issue. Previously it was leaking and I kept towels under the dishwasher. Then one night there was a deluge of water all over the place. One guy says the seal is bad then another no its the whole seal around the dishwasher is bad. No one seems to know and I dont want to spend $250 to find out. I remember a previous post that said their was a design flaw with a part of this but cannot f


... LG 24 in. LDF7810 Built-in Dishwasher

I have the dishwasher model number FGHD2433KF, I have noticed in the last few that I have used my dishwasher no matter what setting I push after a few minutes it jumps to 99+.... Example a push quickwash and start it, the time that shows on the screen is 50, it counts down to 49 then it jumps to 99+. Every setting I originally set starts out at the right time that is listed in my book but then after a few minutes it jumps to 99+. Do I need to call service. I purchased the dishwasher in May of


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

Hello there, I have a Bosch Logixx dishwasher which I purchased just over 2 years ago. My upper dishwasher tray is not fitting properly into the hose pipe holes on the inside of the back wall of the dishwasher. It has a movable plastic mechanism sort of fitting which is dropping off everytime I open the tray to keep the utensils and unable to close it fully until I re-adjust the plastic to fit into the holes proeperly and then it works. I am not sure how to fix the problem, do I need an En


Hello Deepak,\015\012\015\012You can definitely fix this yourself, but I'm not entirely sure from your description which part is "dropping off". It may be a simple fix where something needs to be clipped back into place or you may need to ... Bosch 24 in. SGS69L02 Logixx Built-in Dishwasher

THe ProScrub light is steady, and the dishwasher does not work. When I push buttons, the light keeps going off, and with the next button push, it goes on. If I leave the dishwasher like this for a while, then a couple of the other lights, I think the Normal and Heated Dry lights will blink continuously. In either state, the dishwasher does not work.


... KitchenAid 24 in. KUDS02FR Built-in Dishwasher

Kenmore Elite - 9 Year old Dishwasher - A circuit blew and the dishwasher stopped in mid-cycle and did not drain.... I reset the circuit breaker and "manually" took the water out of the dishwasher. When I push buttons to restart the "95" shows up for the normal cycle. However, when I push start the "95" becomes a "--". Suggestions???


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

The brackets to hold the dishwasher back under the counter do not align with the holes that were drilled in the granite counter top for the old dishwasher. I do not want to try to drill new holes in the granite. Is there an alternative to fasten the dishwasher under the countertop so that it will not rock out. The model DU1055XTVS3.


You could have a handy person make some new brackets which attach to the new dishwasher's brackets with bolts but are made so that they line up with the existing worktop holes. You can probably use strips of soft metal with holes to fashion these.T ... Dishwashers

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

I have a Maytag Quiet Series 100 dishwasher. There is an icon with a "3" in it just to the left of "heat dry." I just noticed this "3" light is on and the dishwasher won't start when I push the "start/cancel" button. All that happens is the "3" light flashes when you push any of the other buttons, but it won't do anything else. Any help you can give me would be greatly appreciated. Thank you.


The "3" means hold for 3 seconds to child proof it. When it's on, none of the functions work. When you hold it again for 3 seconds, it turns off and your buttons will work again.\015\012Good luck! ... Dishwashers

Dishwasher Model Kenmore # 665 16829000 Dishwasher "Quick Rinse" was blinking and no other buttons would work. Received FixYa solution below: "Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow plenty of air through the two holes on either side. The holes that you need to blow air into are not on the circuit board, but on the plastic underneath the circuit boar


Hi\015\012If the control board detects that a key is stuck in the depressed position, the dishwasher operation will be suspended and the control will flash the light for that key until the condition corrected. If a key without a light is ... Dishwashers

I just bought a used LG LDS 5811ST stainless steel built in dishwasher. The previous owner said he bought it 4 years ago. It's in great shape but doesn't work. It powers up but the water is not pumping into the dishwasher. The previous owner said that he thought it was the pump. He said he took it apart once and cleaned a bunch of crud out of some hoses and it worked for a while then started making funny noise and stopped. When i got it home i powered it up and connected water hose. It seems to


Rom the Service Manual:"1E INLET ERROR Not reached to the normal water level in spite of 10 min. water supply.The Hall sensor is OK?Check the frequency of Inlet Water by the Test Mode." ... Dishwashers

My garbage disposal badger 1 was just replaced with the same badger 1 disposal. my dishwasher will not drain water anymore. the old one had a hole where the attachment to the dishwasher hose goes but ther isnt one for the new 1 but the hook up is there. Do i have to drill a hole in the new 1 for the water to drain out


I THINK NO :\015\012 THE DRAN PATH MAYBE BLOCKED\015\012 ALL YOU DO 1ST TO SURE THE PLUMPING IS OK OUT SIDE THE M/C\015\012 THEN IF IS OK BE SURE FILTERS INSIDE M/C AFTER YOU OPEN THE DOOR OF M/C PERIODICLY CLEAN AFTER E ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2485 seconds