Having problems with your Dishwashers ?

I have a GE dishwasher (GSD4020Y70BB) new in 1996. I replaced the whole motor assembly in 2007, seal was leaking. My dishes are not getting clean now, dried food left on plates, coffee stains in cups not being cleaned. I removed main spray arm, found nothing, turned washer on and plenty of water gushing out. I took the cover off sump all clean. I removed the filter screen in the back, there appears to be a valve with some soft rubber around it. Water gushes out of this, does stop during the cyc


Answers :

Have you checked the drain pump impeller and drain hose? I am curious if there is a back siphon from the drain hose or the waste outlet at the garbage disposal might be blocked or plugged with food debris.
\015\012I would remove the strainer and get to the pump impeller to make sure it is not loose or has fins broken. Disconnect the drain hose at the dishwasher and place a garden hose to it, turn the water on and make sure you have good flow into the garbage disposal.
\015\012Once you have verified all the above, get a couple the jars of Tang orange drink. Fill the soap dispenser with Tang and through the rest in the bottom of the dishwasher. Run the dishwasher through a normal cycle and repeat with the second jar of Tang. The Tang will clean the grease and debris out of the tub, pump and drain with its citric acid.
\015\012Good luck, let me know.
\015\012Regards,
HI,
\015\012
\015\012Please provide the make and model of your dish washer so that I can be more specific with the resolution.
\015\012
\015\012Thanks
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a GE dishwasher (GSD4020Y70BB) new in 1996. I replaced the whole motor assembly in 2007, seal was leaking. My dishes are not getting clean now, dried food left on plates, coffee stains in cups not being cleaned. I removed main spray arm, found nothing, turned washer on and plenty of water gushing out. I took the cover off sump all clean. I removed the filter screen in the back, there appears to be a valve with some soft rubber around it. Water gushes out of this, does stop during the cyc


Have you checked the drain pump impeller and drain hose? I am curious if there is a back siphon from the drain hose or the waste outlet at the garbage disposal might be blocked or plugged with food debris.\015\012I wou ... Dishwashers

I have a Miele G896 dishwasher. Drain light on. Washer won't work. Water clogged in drain area. Trying to remove triple filter system to clean it per owner"s manual, but handle stuck. Tried pressing down, turning both directions, technical taps to free handle, but no luck. How do you get triple filter system out to clean it?


... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

I ran a load of laundry in whirlpoo[ duet ht, model ghw9400pl4, error code p-09 was indicated. water was overflowing from door, and water was continuing to fill the tub. I turned off the faucets, unplugged & restarted in drain mode it hummed but would not drain. I turned the faucets back on and retried to drain but it would only hum. I manually removed the water by losening pump filter. There was no debree in filter except for a little bit of hair. The pump & vain was free & clean, and I co


It is your mixer value that is malfunctioning. ... Whirlpool Dishwashers

Hi I have a Meile G 685SC Dishwasher. It has a water inlet problem. It will not fill and just keeps cycling through the water filling process with the water inlet light flashing. I have taken off the inlet pipe and removed and cleaned the inlet filter and washer and put them back. The filter was blocked with a sand like substance. I have taken apart the antiflood valve also attached to the inlet pipe but it is gel sealed so unserviceable. The inlet pipe itself on removing from the vlave appears


Check that the stopcock is opened fully or whether the water inlet hose\015\012is kinked...Check that the water inlet filter is not clogged and clean\015\012it, if necessary, as described in the operating instructions....Check\015\012that the drain p ... Miele 24 in. Incognito G643SCVI Built-in Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

DW fills up with water after sitting. When I turn off the water supply it does not fill up. Removed solenoid valve and cleaned the filter and check for possible blockage. Put back together and turned on water supply. did not fill up until we used it for the first time after my fix. Could the solenoid valve not be sealing off completly DW is a Bosch SH5316UC/U12


... Bosch Dishwashers

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

My Professional series dishwasher does not work properly. It is only 1.5 years old and glasses on top rack get sprayed with fine layer of particles every time I use it. Other items, top and bottom, are often not clean as well, but glasses are the hardest to re-clean. I have tried evacuating the water left at the bottom of the dishwasher before running, pre-running the hot water in the sink and ensuring that the disposal was run, removing and cleaning the filter at the bottom of the washer. None


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Frigidaire PLD4375RFC Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Zanussi DA6141. Dishwasher will not progress from turning on at wash code c1. Test 1: No kinked hoses Test 2: Put water in by hand and it empties it. Lift out the central sieve/filter and it all appears very clean. Test 3:Inlet water filter clean. No actions except low buzz (?solenoid?) after emptying. (Possible Hint: Previously this washer sometimes stalled with knob rotated 15 degrees clockwise from C1 position and would continue to wash dishes indefinitely, if unattended. This was


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the\015\012cycle doesn't complete, check these:\015\012\ ... Zanussi Dishwashers

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

When washer is turn on iget no water and indacter light doesn't come on. you can here the water value click and machine running. have clean filter in water value


... Bosch 24 in. SHX33A05 Stainless Steel Built-in Dishwasher

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My Kenmore Elite model # 630.16302402 dishwasher isn't getting the dishes clean. A lot of food is still on the dishes after cleaning, especially inside the glasses. There is a white film on glasses and the inside of the appliance. I also just noticed that the upper arm isn't turning. There is about 1/2 cup of water standing in the drain area (not visible until removing the filter tray at the bottom of the appliance). Is this normal? The obvious problem is the upper arm but it seems like the rin


Hello, \015\012 \015\012 ... Dishwashers

We have a Blomberg dishwasher. We came to a finished cycle to find water in the bottom. We have removed the water by hand, cleaned the filter and the hose. The lights come on, but it doesn't respond when trying to run a cycle. It will do it's ''finished cycle beep sequence'' at the end of the cycle that it didn't actually run. We have reset it by holding down the start button. Turned it off and on, etc.


I am curious what the repair guy found. We have the same problem. ... Dishwashers

My GE Profile Dishwasher is not draining at the end of the wash cycle. 2 Inches of water remain at the bottom of the washer. I have removed and cleaned the filter, but this hasn't resulted in any change.


... GE Profile PDW8600J Built-in Dishwasher

Non-functional When turned on, machine functions for 10-15 seconds before stopping. It sounds like there is no water coming in. All filters have been removed, checked, and cleaned. Any suggestions?


... Dishwashers

I've had my Nautilus for 6 years and it cleans very well - but now, it won't drain fully and pools at the bottom of the unit. I have made sure that my garbage disposal was cleared first, too. and that water was draining properly in the sinks. I will need special tools to unscrew the drain filter in the dishwasher, right, or can I just use a pair of pliers to turn the little knobs? I am always careful to rinse all food off the dishes before putting them in the washer, but I guess I wasn't careful


If your model has the screen across the back with the filter, then yes use your fingers or a plier to unscrew the pop up valve assembly at the very back center of the dishwasher. Most likely, the cone shapped part has deteriorated and is not sealing ... GE Nautilus 24" Built-in Dishwasher

Have SHU43C and have had no problems with it. We usually run it on the Quick Wash cycle, but ran it on the Regular Wash cycle yesterday because the glasses seemed to be coming out spotty. After it ran, there were no lights on the display like there usually are. The washer had run and the dishes were clean, but it has not drained completely. There is still about an inch of water in the bottom, despite removing and checking both the Large Object Trap and Fine Filter (neither which were clogged


The drain pump needs to be replaced or cleared of obstruction. ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

Bosch 24in. SGS69LO2 Logixx Our machine runs but there is no water coming into the machine?have removed pipe to check water flow,ok, have removed the filter for the inlet supply,clean.have cleaned all filters and replaced, reset the programs, but still no water into machine.


... Bosch 24 in. SGS69L02 Logixx Built-in Dishwasher

Kleenmaid DW8 top washer does not operate. Apparent blockage in the water supply tube which runs up from the bottom water supply. How do I remove the bottom assembly comprising the main filter, waste trap and micro filter? I appears that these must be removed to access the water supply tube mentioned above.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1938 seconds