Having problems with your Dishwashers ?

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


Answers :

1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is control touch pad error.that is the front panel button pad assembly gone faulty.\015\012-----------------\015\0124 blinks is the MCU error . that is motor controlling unit is faulty.\015\012-----------------\015\0125 blinks is the heating element problem.and 5 blinks also relates if motor speed is got weak.so both the things has to be checked.eith the heating element is cracked or the coils in the motor are getting weak.\015\012----------------\015\012you can order the required parts from\015\012----------\015\012www.partsselect.com\015\012----------------\015\012and in some cases it has been seen that this light blinks five times if any of the button is got stuck up in the front touch pad panel.so press all the buttons and check out are they proper or got stuck-ed in.\015\012-------------------\015\012thanks.this will help.please do rate the solution.thank you for using fixya.keep updated.
This means that the Anti Flood Device has been activated and you should shut off the wtare supply to the machine and call a Service Engineer ASAP as there is a major fault with the dishwasher.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

Bosch exxcel dishwasher. Water emptied but pump keeps running even with door open. Have tried tipping it back and new programme but the timer gets stuck. Will not reset either. Help!


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

ASKO 1555 dishwasher won't run. The anti flood device motor won't stop running but we've removed all the water. All the lights on the front panel blink in unison and when we hold down the start/cancel button on the front, nothing resets. We can't run our dishwasher. We've tried disconnecting power and resetting the circuit breaker but the churning motor won't stop.


Hello,Welcome to FixYa.Based on your description " The anti flood device motor won\\'t stop running but we\\'ve removed all the water " It is likely nothing very serious. ... Asko 24 in. 1805 Built-in Dishwasher

FDB750RCC1 When I start the DW, the motor hums loud then soft then loud then soft...if I advance the dial some sections of the cycle nothing will be running and others the motor is on, but no water is getting into the unit. I just replaced the inlet valve and solenoid and that didn't change anything. I can see water in the recirculating pipe running up the unit, but it will just try to make it up and fall back down. Not sure how to proceed...my thoughts would lead me to the main motor, but


Can you hear the water solenoid click when it calls for water? If so, check that the water source valve is on and water comes out of the valve. Check the entry hose for kinks. Remove everything under the lower arm down to the deck keeping track ... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

Pump is constantly running - trying to pump out water, although there is no water in the tank. This condition remains the same AT EITHER AND ANY reset positions of buttons ABC or programme buttons. Programme END indicator is NOT lit, LOW SALT indicator lamp is ON, LOW RINSE-AID indicator lamp is ON. No apparent blockages. Supply water water is on and free flow.


Hello, welcome to FixYa.\015\012\015\012Based on your description it sounds like the emergency overfill switch has been actuated.\015\012\015\012Here`s what to do and what to look for. ( unbeknownst to many this is built by B/ ... Neff 24 in. S5543X2 Built-in Dishwasher

Full model number is SGS45E08GB/56 Will pump out water if you pour it in manually. Takes in water - sometimes. Main pump runs but no water flowing out of arms. Float switch is not operated and is not defective (tested off the machine). Intake solenoid valve seems to work properly (tested off the machine). Pump continues to run even if door is opened.


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

My dishwasher motor will not stop running, even after disconnecting the power and plugging back in. It does not run through a cycle with any water, but the motor runs even when the door is open.


... Viking DFUD04 Built-in Dishwasher

I have a CDA CW494 dishwasher, which is a rebadged Whirlpool. The pump has been changed by a service engineer, using a Whirlpool part instead of the original, apparently it is superior. It seemed to work OK, but now the main jets only squirt for a short burst when the motor stops or starts. The rest of the time the motor can be heard running, but no water comes from the jets. Could the motor be running in reverse?


I would check to see if there is any blockage in the area of the dishwasher where the water collects to be recirculated through the pump back into the washer. It sounds as though the water isn't being allowed into the pump enough to continue the was ... Dishwashers

Dishwasher motor runs (even with door open), but no Water


I am currently having the same problem with the same model. I have removed the left side panel and suctioned out the water that has collected in the overflow pan. That was tripping the float in the pan. I am now running a cycle and it seems to be ... Bosch 24 in. SHX46A05UC Built-In Dishwasher

Frigidaire dishwasher model FDB857RJS1 not pumping water to the top arm. runs then makes a grinding sound like the motor skipping a gear then back to moving water but not enough pressure to get to the top arm.Unit drains normal runs all cycles but leaves the soap on the door not used.


HI, under the sump housing, there is a major issue concerning the circulation motor. there is a wash impeller that is connected to the circulation motor, via drive shaft and stud. this assembly has been stripped ... Frigidaire Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

My Bosch SHX99A15UC Apexx dishwasher won't drain and continues to cycle (you can hear the motor running, but no water) even with the door open. I've flipped the breaker a number of times and the water eventually drained, over night, but it won't run normally now. Any help of suggestions are greatly appreciated.


... Bosch 24 in. SHX99A15UC Stainless Steel Dishwasher

Water leaks from underneath the unit. Water only leaks when the pump cuts on (pressurizes). It leaks down on to the hose connecting to the water inlet valve on the right hand side of the unit when looking at the door of the unit. When the unit is full of water and the motor / pump is not running the unit does not leak. This unit is a Maytag jetclean dishwasher Model DWU9200BAB about 12 years old


Please change the 'o'rings of drain line and the inlet and also check the drain hose and the inlet if there are any holes in it ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1928 seconds