Having problems with your Dishwashers ?

My Bosch SMU2000 series dishwasher will not complete the wash cycle. Advancing the dial completes the cycle but it sticks again before completing the rinse cycle. I replaced the timer assembly and the symptoms are the same


Answers :

Hi,

It seems to me a Faulty Control Board. You need to pull up the control board and check the resistors on it. If found burned or swelled, needs to replace those.

Note - It's better to replace control board than to repair as you can check input power but cannot check output power. So, it might take a lot of time, even some days to find out the correct fix as you would need to replace each and every resistor one by one and that could cost you more than a new board of around 200 bucks.

Let me know, if need any assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Do Accept The Solution, If Satisfied.
Hello. \015\012\015\012\015\012\015\012check these:

Water-inlet valve
Float switch
\015\012\015\012\015\012\015\012Water-inlet valve\015\012\015\012The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usually located behind the lower access panel on the left or right side. It's the device with the main water line (usually copper) from the house, a rubber tube to the dishwasher, and two wires attached to it.

\015\012\015\012\015\012\015\012Float switch\015\012\015\012The float switch is a small electrical switch that's located right below the dishwasher "floor." Above the switch, on the inside of the dishwasher, is a plastic cylinder that floats up as water fills the dishwasher. If this switch is defective, or if the plastic float gets caught or trapped in the raised position, the water can't enter the dishwasher. If the float switch is defective, you need to replace it.

\015\012
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch SMU2000 series dishwasher will not complete the wash cycle. Advancing the dial completes the cycle but it sticks again before completing the rinse cycle. I replaced the timer assembly and the symptoms are the same


Hi,It seems to me a Faulty Control Board. You need to pull up the control board and check the resistors on it. If found burned or swelled, needs to replace those.Note - It's better to replace control board than to repair as yo ... Dishwashers

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

Hi. I have a 3 year old LG dishwasher. It will not drain. Display shows OE. I completely cleaned the drain assembly inside the DW. I checked the discharge line, it is completely clean. I disconnected the drain line from the air vent assembly at the sink and ran the DW, still will not drain. I disconnected the discharge pump wires and ran current directly, the pump works. I replaced the main control PCB, still will not drain. Please advise. Thanks


Measure the electric resistance of the Drain Motor. (Value should be 20-40 Ohms) If it is out of spec, replace it.\015\012\015\012Please reply with what worked best. Thanks! ... LG 24 in. LDF 7811 Built-in Dishwasher

Have Bosch dishwasher model SHU3035UC/U12 Timer sticks in wash or rinse mode. Can timer be replaced and if so what is the cost? Do you have a diagram available to assist me with the replacement?


... Dishwashers

Replace timer maytag la710 - Maytag Washer Timer 205637 2-05637 W/ Knob Assembly Tested & Works


... Maytag Washer Timer 205637 2-05637 W/ Knob Assembly Tested & Works

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi, I have a Siemens SE24A230GB/17 dishwasher and it is not completing the wash cycle (any selected). It appears to be stuck on the 'wash' part of the program. I have done the reset actions as advised in the User Manual and tried another program, without success. I have found that the possible causes could be the timer or thermostat. The estimated time remaining display counts down, but the program does not complete the wash and move onto rinse and dry. Any help or advice you can provide would


... Siemens Dishwashers

We have and older Jackson model 10 AB at church, used 10 to 20 times per year. The pump motor quit this summer and was replaced by a local appliance service company. About $700 job. Upon using it recently, the first time since the new pump was installed, the RINSE cycle seems very anemic, that is, low volume and low spin rate. The dishes were not completely rinsed. Temperature was correct, 185 degrees. The service person came back to look with no improvement and now the Heaters will not co


Sounds like a wiring problem but it is controled by a thermo to make sure you get to the proper tempt . so ck the connections and mke sure the thermo is good . . and the element is good . ..hope this helps mm . ... Jackson 10A Free-standing Dishwasher

I have a Bosch SGS66E02GB/45 that no longer completes a wash cycle. On "Auto 50C" time counts down from 2:58 to about 1:40 then goes back to the beginnnig and repeats. Spray arms are moving, it fills and drains, detergent is dispensed. I have checked the inlet and outlet pipes, the impellor and non-return-valve in the sump, checked the matrix is clear, checked to anti-flood float and switch and replaced the relays on the PCB. Selecting a rinse cycle will complete. Dishes are warm and wet rather


... Bosch Dishwashers

Maytag MDB 8600 AWB dishwasher Wouldn''t start... just a Heated Dry light. Replaced (already broken) door handle with complete latch assembly. Still, Heated Dry flashes. Tried various suggested combos of 5 or 6 quick button pushes followed by Start. Only get a 50-=countdown that repeats endlessly. Sometimes alternates with the letter L. Once by luck I guess it went into Heavy Wash mode, or at least the diagnostic for it. Completed this fine, then back to the stubborn Heated Dry light.


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

My bosch dishwasher sgs09a15 is leaking on or from the pump assembly can i repair the pump or do i need to replace the pump motor assembly completely en which do i need


I consulted another website ... Bosch Dishwashers

Dial Timer sticks between wash or rinse modes


Hello. Is the water getting hot? Usually the timer won't advance because it isn't getting a signal from the thermostat that is on the bottom of the tub, so it thinks that the water isn't hot enough to go through the rest of the cycle. That is if the ... Dishwashers

I have a Whirlpool ADG937 dishwasher (9 years old) which will not complete a 65c wash cycle. It starts Ok and runs for a long time but then continually bleeps, when I open the door the programme indicator light is on the rinse cycle. If I reset the programme to 65c it may do the same or occasionally it will finish the cycle. I have tried salt top-up, descaling and filter cleaning all to no avail. Is the programmer faulty (can I bypass it?)or should I replace the washer?


... Whirlpool Dishwashers

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy


Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Washer went dead. replaced thermal fuse and it worked for about a week and went dead again. Before going dead it seemed to take it a long time to do a load of dishes. The last load ran 1 1/2 hours and still showed 45 minutes to go on the timer before it quit completely. Any ideas?


Sounds like you have a bad control board on unit.and the reason the thermal fuse went out is one of the relays are getting stuck on unit. before long the fuse will go bad again when the resistance level gets to high again. i would replace the control ... KitchenAid 24 in. KUDP01DL Built-in Dishwasher

Dishwasher is 8yrs old. We have lived in our home for the last three years and for the past 2 1/2 has given us great service. Now for thew past 3-4 months our dishes and untinsails have a heavy residue on them at the end of a completed cycle. We have had a new piston assy , timer, and rinse aid dispenser install. We have tried advertised cleansers to no avail. Since the last two items have been installed, we have tried twice to no avail.


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... GE Nautilus 24" Built-in Dishwasher

Dishwasher hey! i have a frigidaire dishwasher. turns on, fills up with a little water and just sits there for about 10 mins doing nothing. starts to clean then nothing some more. it drys everything but leaves the dishes totally filthy even though they are well rinsed prior. after they are dry, the dishwasher then pushes out the remaining water like it is supposed to and on into the disposal. any ideas? i cleaned the pan out completely and replaced the lower parts. thanks!


DEAR FRIEND,\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012ngfam1 here for you!\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\0 ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a AM9T2 dishwasher. It appears the cycle time is bad it does a wash stops skips a rinse a goes back in wash.Is there a replacement cycle timer? I also need a wiring diagram and parts list. Thanks, Scott


... Hobart Dishwashers

I have a Kitchenaid whose chopper assembly keeps getting clogged. I have aleady replaced it. It seems to be dust or maybe cat hair. (Yes we have a cat but rinse the dishes before putting them in.) I pull the chopper, clean the screen and its fine for about 4-6 weeks. Any ideas where this might be coming from or how to avoid the issue?


... Kenmore 16079 Built-in Dishwasher

Leaking dishwasher The dishwasher leaks a stream of water at the base -bottom left corner whenever it goes into the final rinse cycle. It does not leak when it is in the wash mode. This leak just seemed to develop suddenly. There was no build up -ie a small stream of water. I just noticed a big puddle on the floor one day after dishwasher had completed its cycle water leak in the left side ,bottom ,husband states a small drip,drip and we do not know what to do or replace. No water standing


I just had this same problem and it was caused by a small plastic seal on the bottom of the door. My friend owns an appliance store and he said this is a common problem for this model of dishwasher. The part was $68 and the labor was $60. I could ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a Bosch dishwasher that is about 4-6 years old (model SHU8805UC/U12). A few days ago I found clear water in the tub hours after the wash cycle had completed. I drained the tub by resetting the cycle as instructed in the user manual, but the tub gradually filled up with water again after several hours.. will replacing the inlet valve solve this issue?according to what I can tell for my model the water valve assembly (part No. AP3783031) is the part I need. How difficult and expensive


Just pulled mine out last night. You have a different model but it should be the same. Remove the bottom dress panel and detach your inlet hose from the water valve assembly (have a rag handy to catch a little water). Two torx screws on the front ... Dishwashers

Dishwasher does not complete the cycle. Timer stops at about the 7 oclock position, partially thru the rinse cycle.


Dishwasher cycle does not complete:\015\012\015\012Test the timer motor\015\012 ... Kenmore 15129 Built-in Dishwasher

My Frigidaire Model FDB2810LDC1 dishwasher will not stop running. Seems to complete a normal cycle and different cycles can be selected with normal time countdown but at end only rinse agent low light remains lit and sounds as if pump is still running. If opened, water appears to be streaming from rotator arms. Have cycled power but symptoms remain.


... Frigidaire Dishwashers

How do I replace myself the detergent/rince aid assembly on a Maytag Jetclean dishwasher EQ plus model #MDB9150WB? I only need to replace the door, but I don't see a part for that, just the entire assembly. Please advise how to replace myself the entire assembly or can I just purchase a door from the detergent/rince assembly? Thanks, Carol


Carol,\015\012\015\012This is a simple repair. Remove the screws around the outer door edge and separate the door. The dispenser is clipped into position with several screws. Remove the screws and push the dispenser through the door.You can pur ... Dishwashers

I am working on a d8 dishwasher and found the cycle timer (49 sec/ 11 sec) faulty. Ordered a replacement timer from russell food equipment. The new timer is different mounting and timer motor specs. Can you tell me if this timer is the proper replacement. New part number cpn14480


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1129 seconds