Having problems with your Dishwashers ?

Bosch smu 7056 runs but I'm not getting any water. not sure which part to check first


Answers :

Check to make sure the supply does not have a check valve. If it does remove line and re install. If is doesn't check the inlet supply valve.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch smu 7056 runs but I'm not getting any water. not sure which part to check first


Check to make sure the supply does not have a check valve. If it does remove line and re install. If is doesn't check the inlet supply valve. ... Dishwashers

Hi: I have reviewed the forums and tried to fix this issue. Have a Miele G2120 dishwasher that at the end of the cycle - the three (rinsing, drying and end) orange lights begin blinking in harmony. I have removed the triple filter, and two plastic parts to the impeller and made sure all was free of obstruction. I then pulled it out removed the drain hose from in-sinkerator; removed the water line and checked for obstruction. When it gets into this condition - the majority of water drain


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Miele Inspira Series Dishwasher w/ 6 Programs and 5 Temperatures - G2120 / G2120BL - Blac 24 in. Built-in Dishwasher

Where can I get the instruction manual for a Bosch Classixx Dishwasher SGS53C12UK? I have bought a second hand dishwasher that has only been used for 6 months. The programme works fine but when I go to use it again - check water shows on the display. I have to tilt the machine back as water is stored at the base of the machine, surely this is not normal? It there a simple solution to this or alot of cost involved with a new part? Any help would be much appreciated. Thank you.


... Bosch Dishwashers

Water stays in the top draw filter area, have checked hoses found good connection and no kinks in the lines , could this be a pump motor problem. I have had a problem the first month with this unit and the tech. replaced a lot of parts including the computer for the top draw . i am now out of warr. time not by much and am starting to get upset that this problem is happening after such a short time.


... Fisher and Paykel DS605I Built-in Dishwasher

Dishes not getting clean, not sure real sure if water is getting to all the dishes checked the spray arms to see if clogged but don't know how to check the pump like the manual suggest, how do I get to the pump, dishwasher is DU920PW


Try a dishwasher cleaning product. Relatively easy to check if the pump is working. Line up both the spray arms front to back and then run a sequence and see if the arms have moved. If they've moved the pump is working ... Whirlpool 24 in. DU920PW Built-In Dishwasher

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

My dishes are not getting clean. There is dirt and residue on glasses and other dishes. I have checked and nothing seems to be clogged, but I'm not sure I checked everything. The inside edges have a build up of dirt and residue, like the water is dirty or the dirty water is not draining. What should I do.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

I need to clear out broken glass from the gray pan underneath where the water drains to, but I need to take the twirling water sprayer off first to get to the next piece that looks like it is bolted down, and I cannot see how to remove the twirling sprayer part. The piece in the center of it does not appear to be a screw off part, so I am at a standstill.


Hold the twirling sprayer part and unscrew the big round nut part just above it, then you will see a 3/8 nut,remove it and sprayer arm will come off ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Bosch shx33a05uc/14 dishes are milky with white chalky residue. Have cleaned the inside, and checked to make sure the water can exit the spray holes in the circulating parts (top and bottom). Checked that hoses are not kinked too. Seems like it's rinsing with dirty water.


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Bosch 24 in. SHX33A05 Stainless Steel Built-in Dishwasher

We live on an island in the Caribbean and we have a LG dishwasher (model LDF 8812) that has worked fine for a year, but has recently stopped washing effectively. At first, the top part dishes were coming out still soiled from food. Now the bottom part dishes are coming out soiled as well. We checked both the Owner's Manual and the Service Manual and none of the troubleshooting suggestions appear to be relevant to our problem. The water here is very hard, and the water pressure is low and fluctua


You really need to replace the O ring . Could cause leaks and low wash pressure without it.You may also try running a solution of WHITE vinegar and water through the machine every six months as it helps desolve any lime scale (which is going to ... LG LDF8812 Stainless Steel Built-in Dishwasher

My dishwasher will not drain. it goes through the first 10 minutes of a program then i get the OE error code. i have checked my hose for kink or clogged-there is none, i have made sure it was level. i would like to get the filter off but it looks like i would have to take the drain pump out from the bottom to check if any thing is plugging it. was just wondering if anyone has any tips that would help. thanx


1)check the drain pump working\015\0122)check any block from drain pump to drain hose. ... LG LDF6810 Built-in Dishwasher

When dishwasher drains the water not all the water is drained. Some stays standing at the bottom and starts getting an odor after awhile. This is a replacement dishwasher in a 35 year old house. How important is the air release part in the draining situation? I was told by someone that the newer dishwashers have the air release part which was not hooked up on this dishwasher when installed last year. Are there some other possibilities of things that can be checked. Model Number is DU


... Whirlpool DU1055XTS Built-in Dishwasher

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

Dishlex Global 300 Fills and then stops. faint electrical smell after a while . Checked heating element that I replaced 8 months ago, seems OK. It has 29X? ohms resistance and looks OK. (I am not sure of the reading on my meter but the element is not fused.) Pumps water in and out OK No blockage in pump or filters Water level looks to be low on filling, only part covers the heating element. I tried instruction book on changing water level using the "Eco" button no response as indicated in


You need to open the front cover and check the wiring for any burnt wire,this happen sometimes,if that does not solve then it't either pcb or electric motor causing this smell.You would be better off with a new one then. ... Dishwashers

I have a Miele Dishwasher 2430 Sci. It's been not used for 5 months and when I returned it worked fine for several times (at least 6). NOW the intake/drain light keeps blinking. I have already cleaned out the drain and replaced it properly (there was nothing in there and it was clean). No water is coming into the dishwasher?however I know that the water hook-up is on (the first thing I checked). I turned the water on and off several times and AM SURE it's on now. What else could be


The usual course of events is to check and clean the filter, check and clean the water pump and well, check and clean the waste pipe and any connection to a sink or waste disposal system, then check the inlet warer pressure, then the machine level / ... Miele G2430SCi Dishwasher

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

Neff S4752 My dishwasher starts but only for 30 seconds it stops at the first request for water. I've checked the inlet filter and there is definitley water getting through. Is there a solinid somewhere that is not operating?


I had the same problem with mine. I ended up having to pull the dishwasher out from under the counter and tipped in on it's face. My problem was apparently with the pump motor. It would come on, and I knew this because I could hear the hum. Well ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

I have a JDB1090AWS about 3 years old. We noticed a smell and found cutting boards and plastic cups melted. Machine was off. Had to turn off the breaker. Checked both leads to element & have power even with machine off. Not sure if it could be the limiting thermostat; I assume that is to shut the heat down when it gets too hot. Element is on though when it shouldn't be to begin with. I did have to tighten the water supply. Had some water underneath, but all wires seemed dry. Any tests I should t


The heat element can only get so hot.It's timed so it doesn't exceed a period of on, exposing dishwasher contents to continuous high temps.Watch the timer and take note how long it broils your cookware.Good luck. ... Dishwashers

My gas power washer will not start. I filled the gas, checked the oil, set the choke, made sure it was on, changed the spark plug, checked the air filter, and drained any water. When I pull the cord to start I don't even get a putter. Anything else I can try or do I need to take it to a service place.


Will it run if you pour a small amount of gas in the carb? If so, it's a fuel supply problem. Most likely a stuck closed float needle. ... Honda Maxus Pressure Washer MX5222

Dishes on top rack are not getting clean. the spray arm does rotate when I spin it by hand, but not sure it is spinning when door is closed. Water is present on the spray arm when I open the door to check. Can you suggest things I might check or tell me what may be occurring?


Remove the spray arm and clean each nozzle then fixed it back and test but be sure that the wash pump is working. ... KitchenAid Dishwashers

After it cycles I open up dishwasher and the soap tray is open with soap leaking out and on dishes. How can I tell if this is a problem with float switch or water inlet valve because I think it's not getting any water? have maytag MDB3700AWE. also checked to make sure nothing stuck in float.


Try this link it should help http://appliancehelponline.com/dishfloatwaterinletvideo.html ... Maytag 24 in. MDB4600A Built-in Dishwasher

My bosch excell dishwasher won't drain it stops during the wash and won't restart until I have emptied the water then it will wash ok until it gets to the drain part of the programme then it stops again. The red warning light comes on for check the water


A clog in the drain line or air gap (if there is one) is the usual\015\012reason that a dishwasher won't drain. Often the problem is at the point\015\012where the drain line attaches to the garbage disposer or household\015\012drain line. If you remo ... Bosch Dishwashers

My ariston lsv 66 dishwasher will not start washing cycle. It makes the pumping noise as it normally does at the start of the cycle and some water enters the bottom of the machine but then it stops. I have checked to make sure that there are no leaks so the problem is with the filling up of the machine. I live in a hard water area and haven't used anything to help reduce the limescale so expect this to be playing a part. I have tried all the washing cycles but the same thing happens. Any advic


HERE I AM I LIKE THIS JOBE\015\012 PLEASE CHECK THE WATER INLET FILTER I FEEL FROM YOUR DESCRIBE IS IT\015\012 YOU NEED TO CLEAN IT BY ASMALL BRUSH >\015\012 THANKS ... Dishwashers

We're having same problem with our whirlpool GOld quiet partner III. We moved into our house three years ago and no manueal was left. I am sure its a filter or plug but I can't seem to figure out how to get to the filter or plug. I can take off the arm but then nothing. Is there a manuel I can get or can someone explain exactly where the parts are that I need to check? Dishes have grit on them, white spots, just not clean at all. Thanks!


The problem is hard water. There is a new product out called the dishwasher filtration system. It filters the water before it enters your dishwasher. It works amazing and has a money back guarantee. You will love the ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1271 seconds