Having problems with your Dishwashers ?

Problem with door hinge. Door locks but falls to fully open position when not locked rather than staying ajar 6 inches. Dishwasher circa 10 years old - " Orbital System"


Answers :

Look for a broken spring at the hinges. May need to remove the inner door panel.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Problem with door hinge. Door locks but falls to fully open position when not locked rather than staying ajar 6 inches. Dishwasher circa 10 years old - " Orbital System"


Look for a broken spring at the hinges. May need to remove the inner door panel. ... Dishwashers

My 6 years old fell on the Bocsh dishwasher door when it was open and the door dropped about an inch. I continued to work with no leaks. I replaced plastic stoppers but it didn't bring the door up


The sprins on the door could have been over streched and become slack thus not pulling the door up to shut . ... Bosch SHE55R56UC 500 Series 24 In. Black Recessed Handle Built-InDishwasher

Have a Kenmore dishwasher #665.1677993, approx. 13 years old. Upon starting new cycle the pump turns on for a few short seconds, then off, then after a couple minutes it goes on again for a few seconds then off, then later in the cycle it does stay on for a longer period of time. In conjuntion with this intermitent problem it has begun leaking out the bottom of the front door. I have checked drain line, check valve, strainer/screen and vent in the door. I assume it is an electrical issue?


... Kenmore Dishwashers

I want to replace the door spring in an old Kenmore dishwasher, but the screws to remove the bottom panel are flush with the kitchen cabinets. Can I move the dishwasher forward about an inch to expose the screws?


Hi and welcome to FixYa, Initially, pls check the piping works and the drainage connections by visually inspecting these. Normally cabinet works at the sides should allow you this. Additionally, pls make sure that the electrical connecti ... Dishwashers

My built in dishwasher door will no longer stay part way open it went klunk when I left it barely open and now feels like it weights a ton. All the controls are on the to edge and it has a huge handle that goes acroos the whole front it is about 4-5 years old.


Hi there......you havent stated which tye or model your appliance is...however it sounds like your door spring /suspension cords or cable have broken....on some appliances their replacement is quite simple..however be warned other tyes are quite inv ... Kenmore Dishwashers

Our 9 year old Maytag MDB6100 dishwasher starts fine. Partway throught the cycle, it stops, but lights on buttons stay lit. Pressing the door closed more tightly restarts the cycle until the same problem recurs again. what is the problem and the fix? We had a recall on the wiring harness that was repaired a couple of years ago.


... Maytag Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

Customer bought house with a Viking Dishwasher already there. He has no user manuals or documentation with the model number listed. None of the stickers on the side of the door have a Viking model number. This unit is a Quiet Clean System with Auto Water Heating and is (he thinks) about two years old. How can I find out what the model # might be or better yet how do I find out the part # to fix the main control board / interface. It just keeps blinking.


Check the back of the unit for a tag.... otherwise - removing the clock... it should have a part number on it.\015\012\015\012Thanks! ... Dishwashers

My dishwasher 'start" button won't kick in. The machine seems to think it isn't locked - light wont activate, but the door IS locked. I select the cycle and option, but when i push start, it won't stay, The "clean" button keeps flashing. This is 5 years old


Hi,How many Blinks are there?Is it 7 Clean Light Blinks?Let me know, so that we could proceed.Hope i helped you.Thanks for using ' Fixya ' and have a nice day!! ... Kenmore 24 in. 17032 Built-in Dishwasher

Hello,I hope you can answer the question below for me. My dishwasher is a Hotpoint model BFI680 - integrated. I want to replace the old interlocking assembly with a new one as the spring has broken and I can not close the dishwasher door. I have trouble removing the old interlocking assembly though. I can not see any screws that keep it into place as with other models. Instead, it looks like that it is "clipped" to the dishwasher door via the two inner side round holes at the bottom. Tried to re


... Hotpoint 23 in. BFI68 Built-in Dishwasher

KitchenAid KUDI10FL dishwasher- The door spring system broke and I repaired it, but now all of the sudden the dishwasher will not start. The door may have been dropped a couple of time before the spring system was repaired, but it did not hit the floor, just a hard sudden stop. All of the cycle setting lights come on when they are pressed except for the start button. Just before the start button stopped working the dishwasher started by itself or started several hours after cycle selection had b


Hi- It is possible that the door latch is not completely engaging. If the door dropped the hinges may have bent a little thus preventing a good contact with door switch. Try pressing and holding the door shut, hard, and pressing start. If that wor ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Kitchenaid dishwasher model KUDV24SE. The "door open" light stays on. I have tested the switch on the door and it appears to be working. There is nothing blocking the door closing, the light just stays on which prevents the dishwasher from working. I am technically astute, just can't solve this problem (yet)..


... KitchenAid KUDS24SE Built-in Dishwasher

Renlig dishwasher door will not stay shut


... Dishwashers

Frigidaire dishwasher 15 months old. just started not washing dishes very well. set it for high temp wash. put plenty of fresh dishwashing liquid in. the unit goes thru a full cycle. you open the door and dishes are still dirty. there is always lots of dishwash liquid in the door. some of it runs down the inside of the door of the unit. just does not use all of it so dishes dont get cleaned. what could it be?


First I would check to see if it is getting enough water. There is a screen in the water inlet valve that tends to pick up debris. Follow the links Di ... Frigidaire Dishwashers

DOOR REPLACEMENT I have a GE-Triton XL dishwasher model GSD6600G00WW in white that is only about 4 years old and I'm now redoing my kitchen and want to change to Stainless steel. Can the door of my dishwasher be changed to a new door instead of buying a completely new dishwasher?


On most dishwashers the front panel is removable/replaceable. You can try www.coastparts.com or www.marcone.com ... GE 24 in. GSD6660GSS Built-in Dishwasher

My dishwasher emits a dead animal smell immediately after filling. I have a 20-year-old KitchenAid KUDS220T3 dishwasher. The racks are a little corroded, but it still cleans dishes just fine. About two months ago, it started smelling like a dead animal immediately after the dishwasher fills with hot water, during the time the water is being heated, but before agitation begins. The smell appears to be coming from around the door. If I open the door, everything inside the dishwasher smells fine.


This vent that you are describing is to allow air to flow in for the heat/dry cycle. Some times little creatures want to "mark" their territory by "spraying". Spray some type of cleaner like ammonia into it and **** it out with vacuum a few times. Mo ... KitchenAid Dishwashers

Leaking dishwasher I replaced the door gasket, and I still have leaking from under the dishwasher. There is such steady droplets from the bottom of the tub of the dishwasher, it is almost a steady stream of water. It is dripping from about 13 inches deep into the dishwasher from the front door.


... Kenmore 24 in. 17372 / 17374 / 17379 Built-in Dishwasher

Hello! I have a Kenmore Dishwasher Model # 665.15805890. The dishwasher came with the house and I'm guessing it is around 10 years old. My toddler was having a great time flipping the door to the soap dispenser back and forth until he pulled the door off of the pin. Now, I can't seem to position the spring in a way so that the door will spring back. I never looked closely at the hinge before, so I don't know if that is the only reason the door will not release the detergent, or if something


Hi.Please see if the diagram here can help you. Check if the spring is that indicated with nr ten in diagram. ... Kenmore Dishwashers

DISHWASHER I have a problem with my CDA - CW494 dishwasher (6 ½ years old) You can switch it on and the lights come on. Then when you go to shut the door the lights switch off and the dishwasher doesn't start. If you move the door up and down the lights switch on and off. My husband has checked all wiring connections and they seem fine.


One of the switches in the door latch are not making contact properly. before you take the door apart make sure the dishwasher is 100% level. this can affect the door lat switches ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I WANT TO INSTALL TWO CABLES IN MY DISHWASHER DOOR, I HAVE THE CABLES, JUST WANT YOU TO SHOW ME A DIAGRAM AS TO WERE THEY GO, MY DOOR TO THE DISHWASHER FELL DOWN, THE CABLE BROKE, MY DISHWASHER IS OLD BUT STILL WORKS GOOD


... Dishwashers

My Hotpoit FDL570g dishwasher (that is less than 2 years old) is tripping the circuit breaker originally during a wash and now when the unit is switched off and and door is closed. I thought it may be a door lock / microswitch problem and replaced the microswitch. The dishwasher was good for four seperate washes but now the problem has come back when crockery is loaded when the machine is switched off. I'm going to check for bare / rubbed leads but not expecting to find this with a dishwasher of


Hi,\015\012\015\012If your washer is tripping the breaker when it is switched off, this is often a sign that water has leaked - or is leaking - into the bottom of the washer under the washing compartment where there are lots of exposed el ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I HAVE A BUILTIN KITCHENAID SUERA DISHWASHER WHICH IS ABOUT 14 YEARS OLD IT SEEMS TO WORK PRETTY WELL. BUT THE SOAP DISPNSER DORRS TICK CLOSED SO THE DISHWASHER FINISHED AND THE DOORS REMAND CLOSE SO THE ONLY WASHING IS DONE WITH WATER AND NO SOAP. THE SOAR DOOR HAS TWO SLIDING DOOR THAT ARE ARC SHAPPED AND SEEME TO BE CONECTED WITH BUTTONS ATH THE CENTER. THE SOAP DISPENSER ID AHITE INJECTION MOLDED PLASTIC ANDY IDEA I CAN TRY TO GET THEM TO OPEN DURING WASHING CYCLE THANKS **** VON ROTH


Water does not come into the washer ... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

The clean light on my Kitchenaid Dishwasher model KUD124SEBL4, stays on even after opening the door after w wash. Also 4 out of 5 time when you start the dishwasher no water turns on you have to cance


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

I have a Kitchenaid dishwasher. Mod # KUD102CRBS1 which is hardly 2 years old. The door keeps separating from the trim and water seeps out, I fastened the trim, this took care of the problem for ca 6 month, now it is leaking again from the door, has anyone the same problem? I am steaming mad, this was an expensive appliance, which could only clean dishes somewhat with one brand of detergent, all other brands leave a gray film, and now this! MY previous dishwasher was a rel. basic GE but it got t


This is a fairly common one... I always use a silicone sealant/adhesive to make sure it stays put. A thin film does wonders. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2435 seconds