Having problems with your Dishwashers ?

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

My Whirlpool dishwasher ADP 5340 stops after 5-10 minutes, Start button flashes 8 times. After I press it works for about a minute and starts flashing again


... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

Dishwasher keeps stopping and beeping continuously until I press the start button again and shows the F8 Code. When I press the start button it continues for about 5 minutes and then stops properly but there is lots of foam still in the bottom of the dishwasher.


Sir i think the problem would be in any of the three areas. any prob in these areas would lead to the problem u specified\015\012\015\012Test the timer motor.\015\012 ... Dishwashers

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

Zanussi ZDT6053 My dishwasher wont start. I just put the tablet in and after about 5 minutes started flashing and beeping. The programme setting is flashing and the sound goes beep beep, beep beep continuously!


... Dishwashers

I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut


... Whirlpool GU2400XTP Built-in Dishwasher

I have a kenmore dishwasher model 66515832000 and it starts to do the cycle and about 10 seconds into it it stops and the quick rinse light starts flashing, it wont cancel or let anything else happen. if you open it and shut it , the light just flashes and nothing will work.


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a kichenaid kuds03ftpa dishwasher after start it stops after several minutes and the start light flashes. When i open the door, there is water at the bottom. So i press cancel and the water drains out. Then i restart the dishwasher and it does the same thing.


... KitchenAid KUDS03FTPA Built-in Dishwasher

My Frigidaire model FDBB2040FC3 "acts" like it starts running when I press start but after just a few moments the Start indicator light goes out and the Hi-Temp Wash and Air Dry lights start flashing... I can hear it "running" or doing something but it clearly isn't actually cleaning anything. I've tried cancelling, letting it reset itself and then restarting... even shut it off from the breaker. Each time the problem returns. We're a family of 6 so our dishwasher is pretty important in this hou


... Frigidaire Dishwashers

I have an ADG 6552 dishwasher and the on switch starts flashing a minute or so after pressing it to start the washing sequence. Any ideas? Doug


... Whirlpool 24 in. ADG6552 Built-in Dishwasher

ADP5550 DISHWASHER RINSING LIGHT ON, START LIGHT FLASHING TWICE, BUT STUCK WILL NOT PROCEED WITH THE WASH. I HAVE PRESSED THE START BUTTON FOR 10 SECS, 30 SECS BUT THE ONLY RESPONSE IS THE PUMP ONLY RUNS FOR A FEW MINUTES AND STOPS.


This does sound like a problem with the "anti-flood" device that does detect water (leak / spill) at the base of the washer. This device is a protection device that consists of a polystirene float and a micro swithch. Once a water leak od spill is de ... Whirlpool 24 in. DU920PW Built-In Dishwasher

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

I have a Miele G1140 SCI Dishwasher. When I start it after a couple of minutes the Wash,Drying End Light starts flashing and the machine stops . Please could you advise me if there is anything I can do before calling someone to come and have a look at it.


... Dishwashers

Hi there I have a LD-1204 Dishwasher and most of the time it works fine but every now and then it wont turn on or it will turn on but when I got to press start to start a wash it doesnt do anything. Can you help me please


... LG Dishwashers

I purchased a second hand Electrolux Dishlex DX403 with a kitchen. The dishwasher turns on when I turn the powerpoint on and makes a noise as if it is about to start. I attempt to press the buttons to set a mode and start it and it wont work, the buttons dont do anything. How can I fix this?


... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

Normal Wash, Heated Dry, Hot Wash, and Hot Start lights all flash. Dishwasher will not do anything except beep every couple of minutes with these lights flashing.


... GE Dishwashers

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

When I press start I get a double beep sound and dishwasher wont go. There are no other codes or anything. Its an Lg ld1204mi dishwasher


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

Dishwasher wont start, light are flashing


Should indicate that a power failure has occurred try pushing start cancel then reset options and re start ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

We have a miele g673vi dishwasher. it will not start. when it is turned on the #2 light flashes, but it does not work. pressing any other program button has no effect. the only button that does anything is teh on/off switch


... Miele Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2989 seconds