Having problems with your Dishwashers ?

Door will close but not lock in place preventing me starting a wash cycle on the dish washer


Answers :

Check to see if your dish racks are in properly or take them out and then try the door.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Door will close but not lock in place preventing me starting a wash cycle on the dish washer


Check to see if your dish racks are in properly or take them out and then try the door. ... Dishwashers

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

When starting a wash cycle it pumps out the remaining water as usual. It fills normally but does not pump/wash the dishes. It continues to heat and when first noticed it seemed to have gone through the complete cycle but didn't wash. The detergent door had opened and the soap pack dropped out but it never dissolved. The dishes were extremely hot too. Is the same pump used to both drain the washer and wash the dishes?


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Asko 24 in. 1805 Built-in Dishwasher

Upon selecting a wash cycle and closing the door the machine starts normally (heating water stage) but never clicks to allow water in and wash the dishes. Fails to advance to the wash cycle and just runs without doing dishes. There was water in the bottom after the last wash, filters are clean?


... Bosch SHV46C03 Built-in Dishwasher

Maytag model mdbtt70aww. After the end cycle. open the door and found detergent tab on the bottom and the main wash cover is opened. Maytag diswasher model MDBTT70AWW. Put dishes and so forth in the dishwasher. Put detergent tab and jet-dry rinse agent in the pre-wash section. and close the cover. Start wash cycle after done over door and found the detergent tab on the bottom new the heater. The cover to the main wash is opened. Dishes are are clean. Wish someone would tell me


... Dishwashers

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Bosch dishwasher, stainless steel front- with buttons on the inside top( same as display, and the washing cycle won't start. Water seems to be running into the washer, as I can hear it, but the cycle never starts. Recently, I had clogged garbage disposer issue that has been resolved. The dish washer drains into the disposer, and I had free standing water left behind in the washer for 2days during this time.. Could this be the issue? Can you help me figure out this problem? Thanks!!


... Bosch 23 in. SHU 8805 Built-in Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Gld2445rfs2 frigidaire dish washer when i start wash cycle it goes for 30 min then PF lite comes on and soap dispenser will not open.But if i open the despenser door and start the wash all over it will complete the cycle. the problem is which part is bad??


... Frigidaire Dishwashers

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Kenmore dish washer lights up but will not start wash cycle.


Turn off your dishwasher then try it again ok ... Kenmore Dishwashers

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

MDB 8750 Dish Washer Doesn't start the Wash Cycle.


Seems like the control panel (touchpad) is bad again. ... Maytag Dishwashers

Free standing hobart model KDD 60A Serial # 222601715 Washer does not start when door is closed and locked. Electrical power to wall socked operating. Machine plugged in. Water supply connected. Start attempted in rinse cycle and wash cycle.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or door\015\012lock switch which is not engaging its ... Hobart Dishwashers

Bosch SHX 46L Our dishwasher would complete a cycle everything good. Sometime after, it would spray and wet the dishes leaving water in the bottem of the washer. Now, the pump runs constantly when the washer is powered on and it will not start a wash cycle. Any ideas?


Http://www.computercrowd.com/Itm250480379703_60270_Bosch_Dishwasher_Service_Repair_Manual.aspx\015\012\015\01 ... Dishwashers

I am getting a clicking/ticking noise (1 click/second) from my Maytag (model MDB9100)dishwasher after it goes through its auto clean normal wash cycle. At the end of the cycle the arrow = clean and the clicking sound is there. I opened the washer door for about 1 minute noted the soap containers are empty, dishes clean, machine still hot/steamy. Closed the washer door and the clicking sound resumes. Please advise.


This is the heated dry timer going through the drying cycle until the dishes are dry. The dry cycle runs on a timer and it will click through the cycle until it finishes the amount of time preset on the timer to dry the dishes. ... Maytag MDB9100A Dishwasher

When ever i start my Hotpoint DWF 35 dish washer the numeric display has started showing a very long cycle time, it seems to be adding about 60 mins on what the cycle normally takes. It still seems to wash ok but takes forever to complete.


... Hotpoint 24 in. DWF35 Built-in Dishwasher

I have a frigidair dishwasher FDB1050rem1. The clean light never goes out until I unplug then replug. This started about the same time that the dish washer started to make a loud clicking sound wile washing. The dishes are clean when the cycle is done.


... Frigidaire Dishwashers

Dishes not clean after running. Dishes and glasses have a white residue on them after drying. Water is turned on and seems to ok. When I open the washer after the wash cycle starts there are several inches of water in the washer and the jets seem to be functioning. Thanks for your advise.


Hi If you are noticing that the dishes are not clean, then there are a few things to check for. Check the soap powder if it's kept in a dry environment. Also try replacing the powder with something like a gel or liqu ... Bosch SHU9925UC Built-in Dishwasher

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

ETNA ENF 18500A/5 type: 3.E1.181213221110 36 VLENNL 5 Dishwasher lights are on, and set for running, but the dishwasher does not do anything. Sometimes it makes a slight hum when closing the door, but most of the time, nothing. It stopped running after standard dish washing liquid was put into the machine by mistake. At that time, the machine started and ran through part of the cycle, but did not complete, and did not drain the water. Since then it has not started again. I have remo


... Dishwashers

Dishes seem greasy after cycle. Set on high temperature wash. Does sensor prevent washer cycling if it isn't hot?


... Kenmore 24 in. 17352 / 17354 / 17359 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2074 seconds