Having problems with your Dishwashers ?
Where can I find the power lines/wires to a Maytag Jetclean Dishwasher, Model MDB4100AWB . I don't see them.
Remove the kick plate down by the floor and you can access them
Repair Help & Product Troubleshooting for Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Where can I find the power lines/wires to a Maytag Jetclean Dishwasher, Model MDB4100AWB . I don't see them.
Remove the kick plate down by the floor and you can access them ... Dishwashers
We have a Bosch dishwasher SHX46A06 UC/21. It continually runs. We couldn't find a diagnostic test for our model, but we did for another model. We held down the power scrub and regular wash cycles then turned it on and pressed them again. The delicate/econo light started blinking. Looking at some of the blogs, most often it seems to be the heater or the control panel - does this diagnostic test help to pinpoint what could be wrong? Also, where can we find a good manual for our model - we're havi
Here is a link to the service manual http://cgi.ebay.com/Bosch-Dishwasher-Service-Repair-Manual-/250480379703. \015\012 ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher
I am trying to find what model number our dishwasher is so I can try and find a part for it. It says on the front Maytag Jetclean dishwasher quiet plus. I know its an older one but we are renting and I don't know when they installed it.
If you open up the door, you should be able to locate and see a factory label along one of the sides of the cabinet, where the door closes. \015\012\015\012It might be on the top edge, too, depending on how old it is, but you should be ab ... Dishwashers
Whirlpool dishwasher model #DU1100XTPSB wont work and the clean button flashes 7 times and pauses, any idea? I shut the power off to it at the breaker to see if it would reset, didnt work
... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher
My dishwasher model number kuds30ixbl2 isn't working at all. Went to load it to find standing water in the bottom and none of the lights work. There is power to the dishwasher though
See below This is a post that I just copied to this space "I have a whirlpool Quiet Partner II, Model GU2400XTB1, that just suddenly will not start, as if the power was cut. Circuit breaker is fine. from the little Internet research I've done it looks as thou it could be a thermal fuse problem. How easy are these to replace, assuming that's what it is?" Mine is quiet partner III ... there is power to the connection box at the dishwasher it self (checked w/ light tester) ... but there is no power
Have you tryed leaving the power cord out of the socket for an hour or so sometimes they don't lose the memory until they have been left disconnected for a while ... Whirlpool GU2400XTP Built-in Dishwasher
I am installing a Kenmore dishwasher model 13743. I have direct wired the washer?s terminal box wires to the wall power via a BX wire and the washer doesn?t respond. None of the panel buttons are active. With a multimeter, I find that there is voltage on the wall wires and on the dishwasher end of the BX cable wires that hard wired to the wall current. Even though, when I connect the dishwasher?s terminal box wires to the BX wires as directed in the Installation Instructions (white to white,
Next step to check the door switch...the door must close and the switches on the door must close to send power to the control...let me know ... Dishwashers
I have a hotpoint dishwasher model# HDA1000G00WH. until recently never noticed rinsed water not drained after washing/rinse cycle completed. water level just above the drain cover. i removed the cover to see if i might find something clogging the drain screen but found nothing. i removed the plastic water "return" line & it was not plugged. thinking about pulling the dishwasher out, disconnect the plastic line connected to the bottom of the dishwasher, then remove the "bowel-like" container wher
Take out the pump. You should find a broken rubber flapper indide blocking the outlet tube. Cheap to repair. ... Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher
Kenmore Ultra Wash Quiet Guard 4 Dishwasher model 665160344000 normal wash light keeps flashing. I have done all of the push this button and that button combinations I can find on the internet. I unplugged and repluged the 14 pin ribbon with power and without power --no joy. Looks like I need a new part - which part?
Hi\015\012\015\012Open the door. Within 3 seconds press the following sequence\015\012--Try pressing normal wash, heated dry, normal wash, heated dry, normal wash,\015\012heated dry three times within 6 seconds and then press cancel to re ... Dishwashers
Hi i just got a second hand smeg stainless steel dishwasher it has 3 buttons on the left eco...1/2....and power it has a dial with the numbers 1-5 i have no idea the model number im wondering if u might know how i can find out which is my model out of the hundreds that smeg have
... Smeg Dishwashers
Kitchen Aid Dishwasher model # KUDK03CTSS3 The control panel lights are blinking rapidly, several of them. Nothing works, even after powering off and on again. I see there are instructions to reset the control panel on these before calling for service. How do I reset the panel on this model?
I have a kitchen-aid dishwasher model kuds01flss0. all of a sudden i can't get it to turn on. did the usual...breaker, power cord, ect. there is power going into the unit. dont know where to go from here
Hello, I sometimes have luck by turning the breaker off for a solid 5 minutes. Not 4 and half but 5 minutes. This sometimes resets the control board like rebooting a computer. If that doesn't do it I'd start by checking for 120 volts at the power con ... Dishwashers
I have a KitchenAid dishwasher, model KUDP02FR. The "normal" cycle light is flashing. When I push "cancel" or "resume/start", they start flashing as well, but the dishwasher won't start. I turned off the power and turned it back on. The "normal" light still flashes, but when I press "resume" it all starts over again. Any ideas? I can't find this in the troubleshooting guide I have. Thanks.
Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid KUDI01TBK Dishwasher
Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.
I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers
I've got a GE model GLD4408R00WW front load dishwasher, which was not filling, even though you could hear the motor running. Tried resetting it by turning off the power at the wall switch, and then from the breaker itself, but now, see the "Normal" wash cycle and Heated dry lights blinking when power is returned...
Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Tr ... GE Dishwashers
Just installed fisher paykel model 88270 dishwasher, bottom drawer has no power,and top drawer does not fully drain. Cant find another power cord, is there a second one? Cant locate the manual.
... Fisher Dishwashers
Leaking dishwasher My GE dishwasher leaks when running a load of dishes. The leak seems to be coming from about the middle of the tub about halfway back. I can't see exactly where it's coming from, but it appears to be dripping right behind the motor. Could it be a poor connection? I would appreciate any suggestions. Thanks, Bob Engle I do not seem to be able to find the model number
Probably a leak at the motor seal where it enters the tub. Best to remove the motor if you can and inspect the seal. ... Dishwashers
Hi, we are trying to install our new Bosch dishwasher model: SMU68M05AU. I am surprised to see packing foam and flimsy edging across the top edge that meets up to the stainless steel door edge when its closed. I can not find detailed installation instructions. Is there not a strip that goes across the top to meet the door as the top looks very ugly? The dishwasher door protrudes from the under bench cupboard space so the top part is in view and exposed.
Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Bosch Dishwashers
I have a Lady Kenmore(model 665-1596581) that needs replacing. Is there a current DW model that will accept the wood panels from the Lady Kenmore? Where can I find the dimensions of the current cabinet door kit for the DU 1055 XTS to see if the old oak panels will fit the new dishwasher.
... Whirlpool DU1055XTS Built-in Dishwasher
The dishwasher door has problems opening nas closing properly. As a result the push button is not making contact . the power is there up to the junction. how can I open the area where the touch buttons are to find if power is coming up to that area. My Model no is MDB5650AWB
... Maytag Dishwashers
I HAVE A DISHWASHER, KITCHENAID SUPERBA, I DON'T HAVE THE MODEL OR SERIAL NO#. THE ONLY NO#. I CAN FIND IS 8270140, THE DISHWASHER IS NOT RESPONDING TO ANY COMMANDS, THE RINSE LIGHT IS BLINKING AND THAT IT!!! I TRIED TO CANCEL BUT THE LIGHT COMES ON LIKE DASHES ON THE SGREEN THEN WHEN I HIT CANEL AGAIN IT GOES OUT, AND THE RINSE LIGHT JUST KEEPS BLINKING. HELP ME I THINK IT JUST NEEDS REST BUT I DONT KNOW HOW ? I CAN WITH THE HOUSE WHEN WE BOUGHT IT, HELP!!!! THANKS MARLA
I HAVE A DISHWASHER, KITCHENAID SUPERBA, I DON'T HAVE THE MODEL OR SERIAL NO#. THE ONLY NO#. I CAN FIND IS 8270140. The unit is not drying the dishes?\015\012 ... KitchenAid Dishwashers
I have a KitchenAid dishwasher model#KUDC25CH.The problem that I am having is the touchpad control panel all of a sudden is lit up like a Christmas tree. Just about every red indicater light is lit. The DW will run but I dont know what kind of wash it is performing or at what stage the cylce is in. I have tried canceling the cycle,I have tried child lock/unlock,I have cut the power to the unit for a few minutes hoping the computer panel would reset itself. I am affraid to run the unit in fear th
... KitchenAid 24 in. KUDS25SH Built-in Dishwasher
Hello , My Kennmore Dishwasher is not draining. I cannot find where the drain area is to see if there is a blockage. The model number is 665 157 72990 ( the numbers are worn off a bit and may not be accurate. Thank you.
GO UNDER YOUR SINK FIND THE DRAIN HOSE COMING FROM THE CABINET IT WILL EITHER BE OFF WHITE OR BLACK FOLLOW IT TO THE DRAIN POINT EITHER AIR GAP DISPOSAL OR SEPERATE DRAIN TAKE OFF CLAMP GET A BUCKET AND RUN D/W SEE IF IT DRAINS INTO THE BUCKET THEN Y ... Dishwashers
Our Maytag Jetclean Dishwasher EQ Plus will not turn on (MDB9150AWS) and we cannot find a repair manual to troubleshoot through the problem. Maytag does not offer repair manuals on this model. Any suggestions?
Try this. From what I have found Maytag discontinued the Repair manual but it appears that all MDB and MDC models fell under this one repair manual.\015\012\015\012\015\012http://www.appliancepartspros.com/partsearch/model.aspx?mod ... Dishwashers
Jenn Air dishwasher model # jdb6510amp is leaking and because its in there so tight, I can't see the leak. How do I take the line loose to pull the washer out to find the leak.
Take the line off the garbage dispsol then pull it out ... Jenn-Air JDB6510 Built-in Dishwasher