Having problems with your Dishwashers ?

I have a maytag quiet series 300 dishwashers with no lights on. I check the power it ok, I open the panel and all there was is a circuit board, What should I do?


Answers :

I would check to make sure you have c=voltage at the bottom behind the toe kick you will find the wire connectors make sure you have correct voltage there,,,,,
\015\012 then i would check to make sure you had voltage at the door switch and beyond when door lock is engaged...
\015\012 short of that with this model your control is shorted for some reason and would need to be replaced
\015\012if you need to ill send you an aqctive link to the part it is a very easy repair
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a maytag quiet series 300 dishwashers with no lights on. I check the power it ok, I open the panel and all there was is a circuit board, What should I do?


I would check to make sure you have c=voltage at the bottom behind the toe kick you will find the wire connectors make sure you have correct voltage there,,,,,\015\012 then i would check to make sure you had voltage at the door switch and bey ... Dishwashers

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

Continuous alarm after a power failure an alarm started going off in the door of the dishwasher. the push button panel is not functioning. I opened the door panel and found an electronic control circuit board. It is this board that is making the noise. I unplugged the black and white pair of wires on the lower right side of the board and the noise stopped. this must supply power to board. Anyone know what this problem is?


I posted this under "Ben's" problem as well, but I had the exact same problem. I know which black and white wires you're talking about. I don't know what causes this, but getting new parts did fix it. The black box that all those wires go into on ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Whirlpool dishwasher Model#GU3200XTPS0 No power to unit, Control panel does not have power check the circuit and outlet, are OK. is there any fuse inside the unit? is circuit board has any fuse?


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

My dishwasher was running (Model # MDB9150AWB) was running and stopped. No lights on the front at all. Checked, and it is getting power from the 110 line at the connection to the wires in the lower (stationary) panel. Any thoughts on whether there is a circuit board that needs to be replaced?


... Maytag MDB7100AWB Dishwasher

I have a GE Quiet Power 3 that has completly died. I cannot get a light to come on or anything to beep when pressing buttons. I checked the circuit breaker and outlet and they are both working fine. I tried pressing and holding the reset button on the front control panel and nothing. It seems to have just died at 2 years old. Anyone have a solution? GE wants $80 just to look at it.


A dead set simply means a cut off of power supply. Open the back cover of your dishwasher . Locate the area where the AC cord is located and look for the plastic fuse holder which is usually installed in one of the AC cord line open it and replace t ... Dishwashers

Unit does not power up. checked power to unit ok checked power to latch switch - ok appears circuit board is bad. Traced 120v to board. Any other checks before getting new dishwasher?


Hi mgray770,\015\012It sound like you have done a good job already, but just a couple thoughts before you go buy a new one. If the board does nothing then it could be locked, check your owners manual or whirlpool.com for the exact unlock inst ... Whirlpool Dishwashers

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

Kitchenaid Whisper Quiet Ultima Superba dishwasher will not come on. No lights on front panel. Checked circuit breakers.


... KitchenAid Dishwashers

Kitchenaid Whisper Quiet Ultima Superba dishwasher will not come on. No lights on front panel. Checked circuit breakers.


... KitchenAid Dishwashers

We have a kitchen aid dishwasher model # kudso1msso -- quit working and the control panel button lights are out so i assume there is no power to control panel. we have power at the plug every else looks ok. . could the internal fuse at the control panel be blown or the circuit board blown.


Sounds to me like a 'breaker' must be thrown; ... KitchenAid Dishwashers

See below This is a post that I just copied to this space "I have a whirlpool Quiet Partner II, Model GU2400XTB1, that just suddenly will not start, as if the power was cut. Circuit breaker is fine. from the little Internet research I've done it looks as thou it could be a thermal fuse problem. How easy are these to replace, assuming that's what it is?" Mine is quiet partner III ... there is power to the connection box at the dishwasher it self (checked w/ light tester) ... but there is no power


Have you tryed leaving the power cord out of the socket for an hour or so sometimes they don't lose the memory until they have been left disconnected for a while ... Whirlpool GU2400XTP Built-in Dishwasher

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

I have a mdd8000aws dishwasher. After a power outage (2 days) the power came back on, and the bottom drawer no longer works. It still make the chiming noise when the drawer is opened, but the control panel is not fully lit up and the washer will not start in any mode. The lights seem to flicker for a short moment and then they all stay very lightly lit up. Is this just a bad control panel or is there some other circuit that needs replaced? BTW, the top drawer works perfectly.


... Maytag MDD8000AWS Builtin Dishwasher

I have a Kitchenaid model KUDL02IRBS1 dishwasher. It died with no lights to the front panel at all. I have power at the main wire connection to the unit. I checked the door switch and it works. I checked power at what looks like a solinoid on the circut board and it has 115V.


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

MDBH945AWW maytag dishwasher panel lights will not light up. checked breaker and was not tripped. Hardwired circuit. will check tomorrow to be sure power gets to dishwasher. Suspect have panel control failure. In which case should I box it up for the local dump.


These control boards do not have fuses on them. I opened mine up when the front panel touch pad stopped working and the LED indicators were anemic. This is a sign of the ribbon cable connections have oxidized. The ribbon cable connects the touch p ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

I have a Magtag dishwasher, model #MDB6650AWQ thats not running. I check the power supply all the way up to the door latch and it shows that there's power there. However the circuit panel not lighting up and nothing happens when you push the normal wash cycle or any of the other buttons. I believe the problems is electrical in the door latch handle. Is there any way to check the solenoids which are attached to the door handle before I order a new door latch.


I have the same problem with mine. It is 3 1/2 years old. The repair man was just here and said it is the control panel. It will cost $171.85 for the part and then $53.85 today for his visit and then a return visit when the part is in.\015\0 ... Maytag Dishwashers

Kenmore 13599K600 stopped working. Panel board doesn't respond - no lights, no response. Power getting to unit... checked at hard wire ends behind kick plate panel and power is reaching the unit.


Had the same issue and had to replace both the board and the fuse. Six months later, same issue again. It might be when the "Sani Rinse" is used as it dies at the end with some water left but the water is very clean. Possible defect? ... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

My Whirlpool Quiet Partner IV has alternating flashing lights across the front panel where I make selections for the type of cycle. When these lights are flashing, the dishwasher will not operate. We have already replaced the circuit panel and the problem persists. We have shut off power at the circuit box several times with no success. Please help!


Here is the tech sheet\015\012http://www.servicematters.com/docs/w...%208530866.pdf\015\012\015\012Here is a manu ... Whirlpool Dishwashers

Bosch DW model SHU53A05UC/17 was working fine until yesterday evening. Went to turn it on and now get nothing. No lights, no power zip. It's on its own 20amp circuit. Checked the fuse and it's not blown. Flip the breaker on/off a few times anyway to make sure. I was installing a floor and used my miter saw on the sump pump circuit (diff from the DW circuit). It blew the fuse a few times. Any chance, on a diff circuit, it spiked and damaged a board in the DW? What part (part #) would


... Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0909 seconds