Having problems with your Dishwashers ?

It runs for a minute then beeps and says that water pressure is plugged


Answers :

Get a 1/4 nut driver or philips head screwdriver and remove the screws from the lower front of the dishwasher.
\015\012Then lay on your side and with a flashlight.
\015\012Turn the dishwasher on as if you were going to wash a load.
\015\012See if the motor is turning when the unit trys to come on.
\015\012If it starts then stops, like its trying to turn then there is something st oping the impeller, If its just not getting water to fill, then shut the water off and unscrew the water line from the dishwasher and test to make sure there is good water flowing in the supply line. Sometimes teflon tape can block water or rust may have built up inside the supply L at the dishwasher.
\015\012
\015\012Good Luck!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It runs for a minute then beeps and says that water pressure is plugged


Get a 1/4 nut driver or philips head screwdriver and remove the screws from the lower front of the dishwasher.\015\012Then lay on your side and with a flashlight.\015\012Turn the dishwasher on as if you were goin ... Dishwashers

Dishwasher LFK-011S: First it occasionally gave four beeps (overflow) but no water in bottom or under. I then noticed that with lower water pressure machine worked ok few months. Now last week in the middle of program, drain pump started to run, machine gave four beeps and pump kept running even main switch off. Now when I plug in power cord, the pump starts to run immediatelly


... Fagor LFA013 SS 23 in Builtin Dishwasher

Problems with Danby DW1899WP. My husband and I ordered it from Wal-Mart online and picked it up yesterday. We've read through the manual several times, filled all the appropriate receptacles, plugged it in, hooked it up to the water, loaded it, set it, started it, and it doesn't work. It runs the pre-wash rinse for about five minutes before giving a series of beeps, draining the unit, and switching straight to the dry cycle without actually washing the dishes. Help!


... Dishwashers

After starting a wash, dishwasher runs a couple minutes and then beeps saying it is finished


... Bosch SHX6AP05UC Dishwasher

Low Pressure It runs, and sprays water, but doesn't have near the pressure it had. Its also losing water out a weep hole on the water pump. Manual says check the screens, but I took it apart and didn't find any. Any suggestions?


Sounds like you may need new pump seals. ... Campbell Hausfeld PW2575 Pressure Washer

I'm trying to get a Durabuilt pressure washer (model DB1303) to work. After hooking up the water hoses I plug it in and turn on the power. It sounds like it's running but there is no increase in pressure and it runs continuously. I only let it run for about 10 seconds and then turned it off. I tried it a couple of times...no luck.


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Dishwashing SMEG SDCY 66 (made in Italy) As soon as machine is starts (from program 4) water supply valve open and water running in about let say 5 minutes no any further functioning and some strange nice from below looks like something is running dry. What can be the case?


... Smeg Dishwashers

Water pressure run fine til you pull trigger 2 minutes later water pressure shuts down?


... Karcher 2500 PSI Pressure Washer

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


The usual cause of this is sticky Orings in the water admitance valve.\015\012\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reasse ... NIB Shop Force Universal Pressure Washer Accessoriesnib

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

When I plugged my pressure washer in the motor switch was on and the unit started to run without water hooked up. Before I could get to the unit to shut it off it stopped running and will not run now.


Didn't the instructions say to make sure water was hooked up before starting? This is the reason for the warning. ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

I have a Briggs & Stratton Pro 3400 pressure washer that I got new last year and used for maybe 5 hours and it worked great. Have had it stored since then with stabilizer in the gas (I didn't run it dry) and now it won't run for more than a minute or two without dying. A dealer said it was probably bad gas and I now know that even with the stabilizer I should have run it dry last year before storing. Everything is like brand-new including plug and air filter so it must be the gas/carberator gunk


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Pressure washer has been sitting up for about 2 years.. worked perfectly before I parked it.. lol.. But, I put a new spark plug on, cleaned the filter, sprayed carb cleaner in it drained the gas tank and added new gas.. But it still does the same thing.. It starts in the choke position, runs awhile, and then shuts off. While its running, I tried to put the switch in the run position and it kills. Just wanted to see what an expert would say about the matter before I Brake it down. thanks


... Briggs and Stratton 020275 Elite Series 3400 PSI Portable Gas Pressure Washer

Whirlpool DU1101 Hello, My Whirlpool DU1100 is only 1 year old. The dishes are dirtu and the soap doesn't disolve completely My husband is convinvced it is low water pressure, primarily from a leak in the sprinkler system in the park behind our house. I think it is just a clog of some kind preventing the water from getting into the dishwasher fill and/or spray arms. The maunual says you need 20 120 PS to run the dishwasher I doubt it is below 20 PS because of a leak in the park. Is there anyway


Well you should have water up to the heating element. if there is more than likly your chopper is the culprate. do you make sure that there isn't big food particles on your dishes because that is a lot of stress on that chopper and that is what help ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Karcher 3.86M Electric pressure washer. Plugged it into outlet. Unit started running. turned it to off position. Attached hose. Turned on water valve. Turned on switch. Squeezed trigger. Nothing happened. Will not run. Ciruit breaker was reset.


... Karcher PSI Electric Pressure Washer

My Teka Dishwasher DW7 80 FI does the first water intake operation, it sounds like rinsing, and the you hear the pump evacuating the water and two beeps as when it finishes the complete cycle. About 6 minutes. Then Stops. The lights that stayed on says error E8 according to the manual. I have done the suggested fix as ending the cycle manually and turning off and on the DW. I tested "many" times in various modes and the same preemptive end.


Hi.E8 is alternate washing system malfunction.The alternate washing system consists of a valve located in the underside of the appliance and connected to the impeller motor. The valve opens and closes switching spray on and of ... Dishwashers

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

I have an shx65905uc bosch dishwasher that runs and works except for that there is not enough water pressure to rotate the top wand or operate the top sprinkler. The bottom wand does have water and turn and does the top but it is not enough to turn it. If i remove the bottom wand and plug it off then the top will work properly. I have cleaned all screens and removed the plate to access the pump and all seems fine. Any Thoughts


... Bosch SHX65P05UC Dishwasher

My pressure washer starts fine, shoots water OK. After running for 5-10 minutes cleaning siding I shut off machine. I go to start it again within a minute or two and the thing feels like it's just about seized. If i wait until the motor is completely cool, it will pull start freely and start right up. I think something is wrong with the pump, not the engine.


Your pressure washer may not have an ez-start valve installed from the factory. Without the ezstart valve, you will need to hold the trigger on the wand open to release the pressure to easily start your engine. This link will show you wh ... Briggs & Stratton Pressure Washers

Have a honda gvc 160 power washer. It works ok for a while then loses all pressure. It seems as though when it is not running and the water is attached there is not as much water coming through. Is there a screen somewhere that might be plugged?


Sounds like the machine is not getting enough water.\015\012Please check your water pressure to the machine and also the water inlet filter in case its a little dirty. ... Campbell Hausfeld PW2102 Gas Pressure Washer

My LG dishwasher starts ok and the water feed is ok , seems to run through some of the cycle after a few minutes will make some very loud beeping noises and after that shows a 3 in the electronic window, but in reverse. Hope you can help. Thanks


Does the dw drain .. the beeping noise is a troubl code and it may be the pump not draining .. ck the drain line and the pump in that order . . wlso there is either undrer the dw or in the control panel a tech shee ... Dishwashers

Dishwasher runs for two minutes then stops and beeps display says UI


You have either left the inlet tap shut or the inlet solenoid in the dishwasher has packed up. Is this happening with both drawers or just one? ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Hi! My Bosch dishwasher (SHE46C02UC/22) will not shut off. The display says "1" - like there is 1 minute left, but it will not stop. Yesterday morning I started the dishwasher at 7:30am and at 11:30am I realized that it was still running. I opened it and it still had soapy water on the dishes and had not cleaned the dishes well. Any ideas?


... Dishwashers

I have a troy built power washer powered by honda. It runs for 10 - 15 minutes and then dies. I have replacced the ignition coil, spark plug, rebuilt the carburetor, checked fuel flow and placed the unloader valve and it still dies. Once it dies and the pressure is released it repeats the problem. Any suggestions?


... Honda Pressure Washer PSI 3000
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1770 seconds