Having problems with your Dishwashers ?

Dishwasher sounds like it is running normally, (no grinding sounds or anything)but there doesn't appear to be any water coming into the machine. we checked to see if there was a kink in the line or if perhaps it was a plumbing problem but that does not seem to be the case. I know the circular disk in the front of the machine needs to be down and it is, so can you figure out without seeing for yourself what could be the problem and if so is it worth fixing since I can probably replace it for und


Answers :

Hi there,\012

Well first of all you can check out the following -

Water-inlet valve
The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usually located behind the lower access panel on the left or right side. It's the device with the main water line (usually copper) from the house, a rubber tube to the dishwasher, and two wires attached to it.

Float switch -
The float switch is a small electrical switch that's located right below the dishwasher "floor." Above the switch, on the inside of the dishwasher, is a plastic cylinder that floats up as water fills the dishwasher. If this switch is defective, or if the plastic float gets caught or trapped in the raised position, the water can't enter the dishwasher. If the float switch is defective, you need to replace it.

If the problem lies with any of the above then it is worth a repair.

Good Luck!!

Thanks
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher sounds like it is running normally, (no grinding sounds or anything)but there doesn't appear to be any water coming into the machine. we checked to see if there was a kink in the line or if perhaps it was a plumbing problem but that does not seem to be the case. I know the circular disk in the front of the machine needs to be down and it is, so can you figure out without seeing for yourself what could be the problem and if so is it worth fixing since I can probably replace it for und


Hi there,\012Well first of all you can check out the following -Water-inlet valve - The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usua ... Dishwashers

Bosch E15, I see from your site is a water pressure problem. (thanks) I think we have solved that, it old house water pressure gets low, needed resetting. But now how do I clear the error so I can try it? Sounds like there is air in the system. It is a French Bosch machine, the robinet ferme is blinking, sel & liquid rincage are lit, auto 45-65 is blinking. We opened it while it was running, and this all happened from that.


... Dishwashers

We need to remove the AEG Favorit dishwasher from the housing but the back feet need to be adjusted to lower the machine. Which way do we need to turn the front scews to lower the machine. It is not clear whether the screws lower the feet or the machine.


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

Our 2470scvi has caused all of our glassware to turn white. we use very little soap and we always use rinse aid. It seems to me that it is not rinsing properly. It actually has a sound for about 10 seconds that sounds like a motor is stuck.. This sound occurs twice in each cycle. It seems to wash ok but not great of which I would expect for a supposedly top of the line machine. This problem has always happened and the machine is 3 years old.Is this normal for a miele? If so its not the machine w


Hello macit. I do not blame you one bit for being disgusted about this machine. Let's do this. Empty it out and pour in 2 fulll cups of white cider vinegar. Close the door. Let the hot water run into the kitchen sink until it is as hot as it wil ... Dishwashers

I HAVE A CEAN MACHINE 1210 COLEMAN POWERMATE MODEL # pwo701210 MY PROBLEM IS THE SPRAYER HOSE TO THE PUMP DICONNECTED FROM THE PRESSURE OF THE MACHINE I FOUND 2 PARTS A SPRING AND A LIL BRASS PIECE THAT CAME FROM INSIDE THE ADAPTER NEED TO KNOW IF THERES ANY OTHER PIECES MISSING MAYBE A LITTLE DIAGRAM WOULD HELP SO I WILL KNOW WHAT I NEED PLZ HELP !!!!


Need a repair manual where can I find it ... Pressure Washers

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

My dishwasher begins its cycle with a whirring noise, what sounds like the powder drawer then clicks open, but after that nothing happens. The water does not come in. The dial clicks round a couple more points, the machine 'whirrs' again, but still no water/washing action. The machine then just stops/cuts out. Is this a plumbing problem or an electrical problem?


My guess is that the inlet valve is not operating or there is no water supply to the dishwasher.If it is the inlet valve, replacement is not expensive and it is easy to get to (it is on the end of the cold water hose inside the dishwasher usually at ... Electrolux 23 in. ESI602 Free-standing Dishwasher

Hi, switch underneath our miele g646sc washing machine burnt out. It is situated in a round case, with a polystyrene disc above it. The whole of this plastic case, abour 3" dianeter is clipped under the main body of the machine. Do you know what this one does so that we can try and rectify any problem that has caused the burnout, and any idea of part number or where we can see an exploded part drawing? Thanks! Steve


It is usualy caused by dampness from water in the waterproof tray. the switch is for flood protection.a miele service agent would be your best bet ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Blanco BFDW6 dishwasher drains and sounds like it is going to start but stops after 2-3 seconds. Yesterday it was playing up and made a fairly small puddle on the floor. Electrics seem to have been a problem from early on as after a few months it would let me open it during the beginning of the cycle to add items without needing to restart program. I am not sure if problem is electric (may need a reset?) or due to anti-flood feature.


... Frigidaire 24 in. FDB126RB Built-in Dishwasher

Motor problems? I have a fisher paykel DS6031SS -top drawer dishwasher that the motor makes a loud sound when cycle first starts. Sound seems to be coming from the front of the dishwasher. It is 7 years old. Anyone else have this problem? I llive in a small town in Washington state (Lacey) and have been told the closest place to get parts is Seattle! Thanks.


... Fisher and Paykel DS603SS Stainless Steel Built-in Dishwasher

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

Just need a part number, I have a CA-2003-HDHB pressure washer and I need the part number for the valve kit. also if you could direct me to where I might find a parts breakdown online for my machine, in case I need more part numbers. Thank you. Joe G.


... Mi T M Pressure Washers

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

I have a KUDP02FRSS. Two problems: after completing the entire cycle, I open the door to find each time water staying unremoved at the bottom. My other problem is, I need to really push ******* the door to get the machine start working. What are your solutions for these two problems?


... Dishwashers

I have a Braun combimax 650--it is fairly new. It was working fine last time I used it, but this time, the dial that turns the machine on seems to be stuck. The little button for the pulse does work. I read the instructions, which said that this might happen when the machine overheats and to wait fifteen minutes, but it is definitely not an overheating problem and the last time I used it was weeks ago.I love this machine and now need to use it for quite a number of things--any help you can provi


... Braun K-650 CombiMax Foofs Processor FOR 110 VOLTS

We have a model GU1200XLT1 dishwasher. For over a year, we have a problem with debris being left on the dishes/glasses. We got sandy like debris in the left front section, top rack, after it has cycled. Mostly on the outside of whatever is in that part of the top rack. How do we get rid of this debris problem? Is there some filter that needs to be cleaned? We also have problem with mold/mildew inside dishwasher. I have cycled it with bleach, ammonia, or vinegar, which temporarily sol


... Whirlpool Dishwashers

We have a Bosch Model SKT5102GB/07 and the problem is as follows; we load the dirty washing and start the washing process, the machine then goes through the full cycle of wash. Once finished you open the door and notice that the washing is still dirty and a large pool of water is laying in the bottom of the machine. We have had an independent engineer look at the machine and he has advised that the pump needs changing. Look forward to your reply, thank you. Regards Michael Ballard.


Replacement parts are available here\015\012http://www.repairclinic.com/SmartSearch/SmartSearch.aspx\015\012\015\012on the narrow ... Bosch Dishwashers

My Bosch Classixx (about 10 years old) dishwasher won't fill The problem has only started since I pulled it out and cleaned! The programme sounds are as normal but no water enters the machine. I detected a small leak on the inlet pipe and tightened that. The machine drains when I add water manually though it has made a lot of gurgling noises for some time now when draining. When tipped on its side water comes out of the bottom of the machine (not entirely clear but not dirty either). When upri


... Bosch SHU9915UC Dishwasher

What's your problem?My Karcher K411A is leaking internally, what tools do I need to split the casing to check problem?


... Pressure Washers

Dishwasher i need help either installing for troubleshooting my 18' portable frigidare dishwasher. when the dishwasher is turned opn and it starts to fill the water flows out of the bottom of the machine what is the problem and how dod i fix it is it the hoses ? it also hooks up to the sink it isnot a built in dishwasher so is the hose for the draining need to go in the sink or does it hook up somewhere under the sink?


I would put the dishwasher on its back so you can see underneath to check the fill and drain hose to make sure there not damaged in any way to cause it to leak. if it all looks good under there return it upright and remove the front lower kick panel ... Frigidaire 18 in. FDR252RB Built-in Dishwasher

Intake drain The dishwasher is an excellent machine but the intake drain problem is driving us crazy. I have had pumps changed twice and that has not been the problem. I start the dishwash and within a minute the intake drain light comes on right after the first cycle. I need help!!


... Miele 24 in. Touchtronic Platinum Built-in Dishwasher

Hi I have a maytag quiet series 300 with model # MDBTT60AWW and it will not start. All the lights lite up but it will not start. I recently just had to replace an element due to a recall so when he was hear fixing the element I asked him what he thinks could be the problem and he said it sounds like it possibly needs a new control panel. Does this sound right and if so do you know where I can get a control panel. Thanks for your help


... Dishwashers

I recently replaced the water seals, V-packing & all six check valves in a CW-3504-4MGH pump on a MiTM 3504 pressure washer that had very low pressure. Usually this would fix most pressure problems on most machines, but in this case it had little to no effect. I suspect that the unloaded is the culprit in this case, but since I have had little experience in repairing unloaders (let alone adjusting them). I would appreciate feedback from anyone that has experience in this area. Thanks


Check the wand tip for a tiny piece of debris like a tiny rock or something stuck in the tip. ... Mi T M Pressure Washers

Please help me, I need help urgent. I brought my F-22 Jet Tech in March 2008 for my restaurant. The machine was fine, but got electrical problem, which is very serious, ELECTRIC SHOCK. We cant use it,since we cant touch it. This just happen 3 days ago, I called the prof electrician, but he has no knowledge of the machine, so, he didn't want to even touch it. Please help. URGENT. Thanks Ellen Fiske ph. 347-835-8701 Honeys thai pavilion address : 3036 westchester ave, bronx, ny 10461 email


YOur best bet is still the electrician.\015\012\015\012However, I would get him to go through the electric diagrams contained in this website. Scroll down to the F-22 mode ... Jet Tech Systems 24 in. 737 Free-standing Dishwasher

Drainage Problems My ASKO D3120 doesn't drain properly leaving water in the bottom. I have had this problem before (2 yrs ago) and called the helpline who told me how to reset the machine by pressing the buttons in a particular order which fixed it immediately. Now when I call them they claim this can't be done and they will have to send a technician. Sounds like a money making exercise to me. Does anyone know how to reset through the programming function? Next time I'll write it down and wont h


Turn off the dishwasher by pressing the on/off switch on the top left of the dishwasher. Wait 5 seconds. Press and hold the program button on the right side of the front of the dishwasher. As you are holding the program button, press the on/off sw ... Asko 24 in. D3120 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0923 seconds