Having problems with your Dishwashers ?

My beko DWD8650 dishwasher has stopped working - when I switch on the power, the machine sounds as though it is trying to work, even though the start button has not been pressed. Once the start button is pressed, the timer does not count down and nothing else happens.


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My beko DWD8650 dishwasher has stopped working - when I switch on the power, the machine sounds as though it is trying to work, even though the start button has not been pressed. Once the start button is pressed, the timer does not count down and nothing else happens.


... Dishwashers

With Kitchaid dishwasher KUDS01FL, it wont run. All control buttons seem to work (by lighting up when pressed) except "start". When press "start", it doesn't blink or start. Does this indicate a bad start button switch or something else? Is this something I can replace? Thanks.


Hi Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...-high temp wash - ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

I have a Tecnik TKD795/3 built in dishwasher. It is now making a gurgling noise as though it is draining water when I try to start the cycle, but the cycle does not start and no lights come on at all. I have tried pressing the outside two buttons to reset, but absolutely nothing happens and the gurgling noise continues until I release the power button. Can you help please?


... Tecnik 24 in. TKD795/3 Built-in Dishwasher

I have a whirlpool gold quiet partner III. The cancel drain button works but nothing else. If you press any of the button for a period of time the normal button flashes; nothing happens though. Any thoughts????


Try to reset the dishwasher by using this sequence of keys within 6-8 secs.\015\012\015\012HiTemp/ heat Dry/ Hi Temp/ heat Dry/ Hi Temp / Heat dry.\015\012\015\012If it works all lights should turn on. Press Cancel to exit. ... Whirlpool GU2400XTP Built-in Dishwasher

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

I have a Electrolux dishwasher EID6305. Everytime I close the door it wants to start a cycle even though j haven't pressed anything. Pushing start/cancel button doesn't cancel it. What's the best way to open the door an close it without starting a cycle?


... Dishwashers

I have a kitchenaid dishwasher, SS, model # KUDIO1ILBL6. When you press the ''normal'' button to run it, nothing happens. Tried other cycles and same thing, the green light goes on above the cycle but its just not starting. I tried resetting by opening, pressing high temp scrub then energy saver dry, high temp scrub, energy save dry, then close and hit cancel. Is there any other combo to reset it? or does it sound like something else is wrong? thanks!


... KitchenAid Dishwashers

I opened the door before the drying cycle finished. I pressed the cancel button, then I pressed "normal wash" and the "start" button and it didn;t start. Then did "cancel" again . I pressed the "heat" button for five seconds to lock the door so I wouldn;t make the same mistake again. It still won't start. Now the "cancel" button won't work and the start button flashes. What do I do now?


HI. The unit will need to be reset. This is achieved by unplugging the unit for five minutes. If unplugging is not an option, simply,shut down the appropriate circuit breaker for five minutes. This action will, essentially, reset the logic sector. On ... Dishwashers

Water not entering machine when start button is pressed eevn though pump is working


Check the votage in the inlet valve when the start button is pressed, if voltage is present then the inlet is faulty, can be dirt which can be remvoed and ccleaned orr the valve can be faulty if there is no continutiy test onthe coil.\012If the ... AEG 24 in. Favorit 50740 Free-standing Dishwasher

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

I press the start button and the washing light just blinks nothing else happens


Sounds like a faulty latch...the dishwasher thinks that the door is open, so it just keeps flashing the lights until it's closed. I'd order and replace the latch ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a GE Max,mod # GSD6610G00SB....when I press the start button, the vent closes and before anything else happens the breaker is tripped. I have checked all wiring and looked to see if water has shorted anything on the unit.


... GE Nautilus 24" Built-in Dishwasher

The dishwasher will not begin wash cycle. When I press the "start" button, the "heat dry" light illuminates and the "washing" light blinks, but nothing else begins.


Hi\015\012\015\012When these lights flash on your machine it is actually transmitting a code which can be read by a technician to help determine where the fault lies.\015\012\015\012However there may be a simple fix that you c ... Dishwashers

Dishlex Global 300 does not Function when Program and Start Button pressed even though Power and Water is on


Check the door handle they have a tendency to break away from there plastic hinge,It will feel a bit off line if this is the case as it locates a door switch,Also if that is not the problem you might check the water inlet solonoid.Hope this Helps. ... Dishwashers

I have a beko de3430fw dishwasher that will not fill with water. When the start button is pressed a pump can be heard then after 30 seconds it stops and nothing else happens.


... Dishwashers

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

Hi there. I have a Matsui MF145 slimline dishwasher and having a problem. When I press the on/off button I would usually then press the program indicator button (usually the first indicator - pans) and close the door and the dishwasher would start. Currently i press the on/off button and try to press the program indicator button and the on/off button flashes and there is a continuos beeping sound....and nothing more happens. Do you know what the problem is?


Try to clean the unit, ofetn when the machine is dirty, some sensors are fooled thinking there's some problem. be sure there's no jam on mechanical parts. ... Dishwashers

I have a KitchenAid KUD1021RWHO dishwasher that will not turn on when I hit the start button. The LED lights work when I press cycle selection ie. "normal" but when I press the start button nothing happens. I have waited for a couple of hours and then it will start. However during the last week it has happened more frequently and now it has not worked for the last (2) days. Any ideas as to what the problem may be? Thank you for your help!!!


Hello,\015\012\015\012This is a very common issue on these units. The touch pad has failed. You can try to flip the breaker off for several minutes and see if that clears the code. More than likely the touch pad will need to be replaced.\015\01 ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

We have just had a Hotpoint FDD912 dishwasher delivered but we can not change the language to English from Italian. The manual says turn on then press the P button and start button together but this does not work. When you power on it says Benventui but quickly goes to Autosuperwash and we you press P and start it just starts the programme.


... Dishwashers

I have a F&P dishwasher model DW60CDX1 (around 5 years old) which we cannot start a cycle. The dishwasher turns on (power button and all programme indicators light up) but when you press a programme button nothing happens - the lights don't change. We have switched the power off at the powerpoint and on again a few times but this has not rectified the problem. It was playing up before this in that sometimes the programme would not start when a button was pressed but I just closed the door mor


The micro switch in the door which senses the door closing has probably failled. This is accessible once the inner door cover is removed. Switch should be under $10 from electrical store. Or buy through appliance manufacturer. ... Fisher and Paykel Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1153 seconds