Having problems with your Dishwashers ?

Hotpoint wf310 set wash,it starts then after about 20 seconds the on/of light and the lights to the far left flash


Answers :

You will have to check the error code number which you get as per the blinks.
\015\012f01 light 4, motor triac
f02 light 3 motor, jammed/ tacho
f03 lights 3&4 Ntc fault
f04 light 2. pressure sw stuck on empty
f05 lights 2&4, pressure sw stuck on full
f06 lights 2&3, N/A?
f07 lights 2&3&4 heater relay
f08 light 1. heater relay
f09 lights 1&4 eprom/setup error
f10 lights 1&3, pressure switch not sensing
f11 lights 1&3&4, pump/draining error
f12 lights 1&2, communication error
f13 lights 1&2&4, dryer ntc/ fan motor
f14 lights 1&2&3, dryer heater
f15 lights 1&2&3&4, dryer heater relay
f16 N/A
f17 light 4, door lock
f18 light 3 comms error (3 phase motor) power board

\015\012ignore the on off light
\015\012-------
\015\012as per the fault mentioned you will have to check the fault in your unit and then replace that following part in your unit.
\015\012you can get required parts from
\015\012www.repairclinic.com and also from www.partselect.com
\015\012This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya
\015\012
\015\012
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hotpoint wf310 set wash,it starts then after about 20 seconds the on/of light and the lights to the far left flash


You will have to check the error code number which you get as per the blinks.\015\012f01 light 4, motor triac f02 light 3 motor, jammed/ tacho f03 lights 3&4 Ntc fault f04 ... Dishwashers

We have a Whirlpool dishwasher model ADG7550. It runs ok for a few minutes then it switches to the rinse setting (i.e. the furthermost left light of the temperature lights, i.e. lights from the left, 'rinse', '40degs', '50degs', '65degs', '70degs'. We may set it to start at e.g. 65degs, it does so ok for a few minutes then it switches to the 'rinse' light and starts to beep every few seconds. There are 11 beeps.


HI, There are two areas of concern here. This will be an issue with either the element, or control sector. I suggest to start with the element inspection. This will requir you use a multimeter, if possible. You will need to varify proepr element func ... Dishwashers

I have a Whirlpool ADF951, it has power to it and was working fine, the power light is on and the green light to the far right of the cycle lights is flashing, I can only get any response if I hold the start button in for about 10-15 seconds, The machine stops the light flashing and makes the noise like it is starting , that goes for about 20 secs then returns to the flashing light stage, any idea's please


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water tempera ... Dishwashers

Teka dw6 59 f1, far left light on all the time, far right light flashing, what does this mean ?


... Dishwashers

Teka dw6 59 f1, far left light on all the time, far right light flashing, what does this mean ?


... John Dishwashers

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

Matsui dishwasher Matsui MS452S slimline - second wash light flashing and unit doesn't fill. Tilting it backwards allows water to leak out from the left rear corner then it runs correctly for minute or two before numerous beeps sound and unit cuts out with light flashing again. How do I get into the base to see if there are any leaks? Unit less than 2 yrs old.


... Dishwashers

Have a frigidaire dishwasher (model- PLD4375RFC0)about 2 years old. Set to run as we left to go out of town- when we came back all lights flashing including error- found a child's plastic bowl that had fallen to the bottom and had a melted spot as it was next to the heating element. Called support and were told to master restart- shut the power off for 15 minutes. Did and now flashing "27". Cannot find a code for that and neither could support without sending out a repairman. Any advice before


... Frigidaire Dishwashers

I have a technika diswasher,not sure of the model, is approx 3 years old and has a big dial on the left hand side with 7 wash functuions and the power button is smaller and is on the RHS. I cant remember how to reset the wash settings. I thought that by pushing in the large dial this set the wash cycle but a technician told be that you have to hold your finger on the start/pause button until the green light flashes, and turn the dishwasher off then back on. Can you please give me a step by ste


I have the same model. You just turn the dial to the setting you want, push the dial back in, turn the (right) power button on then turn the smaller start button on. I use different cycles all of the time depending on whats in the load and this works ... Dishwashers

Have a whirlpool ADP 951 and no manual for it. Is was working fine and now the red light in the left hand corner is on and machine wont fill. When I start it by holding the button on the right hand side in, it will drain for about 30 seconds and then stop and green start light flashes. Can anyone offer a solution?


Some mod have codes / could be suds lock or slow drain . i would ( if front loader ) clean out pump . hope this helps . **** ... Dishwashers

I HAVE A GORENJE DISH WASHER WHICH HAS 4 LIGHTS ON THE LEFT THAT FLASH AS IT GOES THROUGH THE PROGRAM,, AS IT FINISHES ON THE SECOND STAGE THE 3RD AND 4TH LIGHTS COME ON AND IT BLEEPS BUT GOES NO FURTHER,,,


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Dishwashers

Electrolux ESL63010 integrated dishwasher 10 months old- works for a few seconds, then stops and beeps continously. & the End indicator light flashes once. I turn it off, cancel programme, set it again, shut the door -it starts and goes on to complete the programme and washes the dishes perfectly. It has been doing this 'performance' for a week now -every time I use it- can you shed any light please


... Electrolux Dishwashers

Hi!, my Ariston L64 dishwasger refuses to start. It seems to reset OK when the dial is turned fully to the left. After the beeps I select a cycle and nothing happens for some time, then eventually the first two lights begin flashing together.That is as far as it goes. Can you help me fix this problem please? Donna


... Dishwashers

Hotpoint BCI450 The Normal Operation setting light (No 2) starts flashing a few seconds after the door closes and the machine also starts beeping and fails to operate any ideas ? I have cleaned the filters etc. This problem is not detailed in the troubleshooting section of the manual. regards


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

Candy CDI1012 integrated dishwasher. The programme lights flash and a beeping noise (like when the cycle is finished) goes on for about 5-6 seconds, and the programme can not be re-set


... Dishwashers

Dishwasher problem dishwasher begins to wash, water flows in, then both first and second green indicator lights flash together and the cycle does not complete. I have cleaned the filters, removed water that's left in the bottom of the dishwasher.


My dishwasher Indesit DI67S will not run on the number 1 cycle. It will fill and then when that programme finishes it jumps straight to the drying cycle missing all the rinses out etc. If on the number 2 programme it goes all the way through but then ... Indesit 24 in. DI67 Free-standing Dishwasher

Indesit dishwasher error codes i have to lights flashing on my indesit dishwasher the second and forth left to right any idea's


Why does the spray arm fall off? ... Dishwashers

When I switch on my dishwasher setting it at normal wash cycle it appears to start as normal then after few seconds goes onto to Eco 45 c wash - the light flashes but nothing happens i.e. no water comes into machine - any suggestions.


You may want to check and clear the pump\015\012you have something slowing your drain\015\012 but for giggles make sure your float valve is free to go up and down like it should\015\012 all dishwashers attempt to drain first\ ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

AFTER I TURN MY HOTPOINT BFV62B DISHWASHER ON AFTER ABOUT 1MIN IT STOPS AND THE GREEN LIGHT SECOND IN FROM THE LEFT STARTS TO FLASH.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

Used some washing up liquid instead of dishwasher tablets, after i got rid of all the bubbles and drained it, it no longer starts. If i switch the power off and leave it for a few minutes i can select a prgram it starts and a few seconds later there is a beep and the solid green run light on the program selectoe is flashing over the left hand program button. At this stage pushing any program button does nothing, i have to swith the power off and wait 5 miniutes and the the above patten is repeat


Dear sir vif you have used liquid soap in your dishwasher it will make mountains of bubles to kill all bubles outin a hurry take a sos pad put it in your machine and run the dishwaser this will remove all of the soao instantly try it it really works ... Ariston Technologies Dishwashers

I have an integrated program 2000 dishwasher which has started to beep since I moved it. The cycle starts but after a couple of minutes it stops and starts beeping and the green light above the start button keeps flashing in sets of 4. I have searched everywhere for a manual but haven't had any luck so far.


... Dishwashers

My hotpoint BFV62 dishwasher wont complete a wash, the second light from the left flashes what does this fault code mean?


... Hotpoint 23 in. BFV62 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1271 seconds